S22: Firebolt

From Embedded Systems Learning Academy
Revision as of 22:44, 26 May 2022 by 243 user1 (talk | contribs)

Jump to: navigation, search
The RC Car

FireBolt RC Car

Abstract

Firebolt is battery powered autonomous RC car. The car uses four microcontrollers for communication between the nodes- driver node, motor node, bridge & sensor node, and geological node over the CAN bus. It is interfaced to the mobile application which sends GPS coordinates for the destination location to the driver node and reaches the destination by avoiding any obstacles that comes in the path. For obstacle detection and avoidance it uses Ultrasonic Sensor and makes the decision of steering and maintaining speed after performing calculations based on the bridge and sensor node's data.

Objectives & Introduction

Objectives

The objective of this project is to get hands on experience of application of embedded systems in autonomous vehicles, have understanding of CAN bus communication, CAN database files, TDD and other related tools such as PCAN dongle and Busmaster.

Software side

  • The car communicates with an Android application
  • Receive coordinates from gps to drive itself to the destination while avoiding obstacles
  • Display useful information on the LCD
  • Take care of elevation and make correct speed decisions
  • DBC file for all the nodes

Hardware side

  • Design PCB for four controllers and other necessary components
  • Choose good options for mounting the ultrasonic sensors on the car
  • Make a good GUI Android application for interfacing with the microcontroller

Introduction

Four Nodes of the RC Car are:

  1. Driver Node
  2. GEO Node
  3. Sensors and Bridge Node
  4. Motor Node
  5. Mobile Application

Team Members & Responsibilities

  • Team FireBolt
  • Team FireBolt

Priyanka Rai

  • Geo Controller
  • GPS and Compass Interfacing
  • Motor Controller
  • Integration Testing
  • Wiki Page Update

Ritu Patil

  • Motor Controller
  • Integration Testing
  • Wiki Page Update

Ritika Beniwal

  • Driver Node
  • LCD interfacing
  • Motor Controller
  • Integration Testing
  • Wiki Page Update

Utsav Savaliya

  • Sensor Controller
  • Integration Testing
  • Wiki Page Update

Dhanush Babu

  • Bluetooth module interfacing
  • Motor Controller
  • Android App
  • Integration Testing

Noel Smith

  • PCB Designing

Schedule

Week# Start Date Target Date Task Completion Date Status
Week 1
  • 03/06
  • 03/08
  • 03/12
  • 03/10
  • 03/10
  • 03/12
  • Study and discuss previous project reports
  • Brainstorm on the requirements for the project
  • Identify and order/purchase the required components
  • 03/10
  • 03/10
  • 03/12
  • Completed
  • Completed
  • Completed
Week 2
  • 03/13
  • 03/13
  • 03/14
  • 03/14
  • 03/18
  • 03/18
  • Distribute initial roles among the team members
  • Study the datasheets and manual of acquired components
  • Create and setup Gitlab Repository
  • 03/14
  • 03/18
  • 03/18
  • Completed
  • Completed
  • Completed
Week 3
  • 03/20
  • 03/22
  • 03/20
  • 03/25
  • 03/26
  • 03/24
  • Write basic driver for ultrasonic sensor
  • Analyze and decide the hardware placement of the RC Car
  • Create SENSOR and DRIVER nodes to transmit and receive data
  • 03/26
  • 03/23
  • 03/25
  • Completed
  • Completed
  • Completed
Week 4
  • 03/27
  • 03/27
  • 03/27
  • 04/04
  • 04/01
  • 03/28
  • Create the GEO node to get coordinates and cardinal directions from GPS and Compass
  • Create the MOTOR node to drive the RC Car
  • Design DBC file and create CAN signals for every node
  • 04/02
  • 04/04
  • 04/01
  • Completed
  • Completed
  • Completed
Week 5
  • 04/02
  • 04/02
  • 04/02
  • 04/02
  • 04/08
  • 04/08
  • 04/08
  • 04/08
  • Finalize the DBC file
  • Design obstacle avoidance and steering logic on the DRIVER node
  • Design motor driving logic on the MOTOR node with the encoder
  • Start and design the Bluetooth app xml for destination.
  • 04/09
  • 04/09
  • 04/09
  • 04/09
  • Completed
  • Completed
  • Completed
  • Completed
Week 6
  • 04/09
  • 04/09
  • 04/09
  • 04/09
  • 04/09
  • 04/15
  • 04/15
  • 04/15
  • 04/15
  • 04/15
  • Integrate GPS module with compass to get the current location.
  • Write UART interface for Bluetooth integration on sensor node.
  • Get raw sensor data from the ultrasonic sensor.
  • Integrate GEO node to DRIVER node for navigation. Check whether the DRIVER node is receiving the coordinates.
  • Backend development for android app. Should be able to scan BT devices and connect.
  • 04/15
  • 04/15
  • 04/15
  • 04/15
  • 04/15
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
Week 7
  • 04/16
  • 04/16
  • 04/16
  • 04/16
  • 04/16
  • 04/16
  • 04/23
  • 04/23
  • 04/23
  • 04/23
  • 04/23
  • 04/23
  • Communicate to the GEO node over Bluetooth via Android app
  • Complete Driver obstacle logic
  • Design driving decision logic based on the navigation data
  • Lay out basic PCB Board design for mounting the ECUs
  • Filtering ultrasonic sensor data and sending processed data to Driver
  • RPM Sensor logic and testing.
  • 04/26
  • 04/26
  • 04/26
  • 04/26
  • 04/26
  • 04/26
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
Week 8
  • 04/25
  • 04/25
  • 04/25
  • 04/25
  • 04/25
  • 04/25
  • 04/30
  • 04/30
  • 04/30
  • 04/30
  • 04/30
  • 04/30
  • Design a dashboard on the LCD to display the values
  • Driver logic for sensor data and geo data on busmaster.
  • Add functionality for pinning location on maps and extracting latitude and longitude
  • Improve obstacle avoidance logic
  • Break and ramp logic for the motor.
  • Collective Test 1: Drive the car to a hardcoded GPS destination
  • 04/29
  • 04/27
  • 04/30
  • 04/30
  • 04/30
  • 05/06
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
Week 9
  • 05/01
  • 05/01
  • 05/01
  • 05/01
  • 05/01
  • 05/07
  • 05/07
  • 05/07
  • 05/07
  • 05/07
  • Design individual architecture diagrams and algorithms for documentation
  • Make any necessary improvements based on previous test results
  • Complete the final version of the Android app
  • Get the PCB printed
  • Collective Test 2: Test the car driving with navigation data from the Android app
  • 05/10
  • 05/07
  • 05/01
  • 05/07
  • 05/11
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
Week 10
  • 05/09
  • 05/09
  • 05/09
  • 05/09
  • 05/14
  • 05/14
  • 05/14
  • 05/14
  • Replace the circuits with their corresponding PCBs and assemble
  • Complete the RC Car structure and assembly with the 3D printed parts - Prototype 1
  • Refactor the code modules with necessary improvements
  • Collective Test 3: Test car on various terrains and slopes
  • 05/20
  • 05/20
  • 05/20
  • 05/20
  • Completed
  • Completed
  • Completed
  • Completed
Week 11
  • 05/16
  • 05/16
  • 05/16
  • 05/16
  • 05/21
  • 05/21
  • 05/21
  • 05/21
  • Revise and improve the wiki report to cover all the aspects of design and implementation
  • Fix all the errors and make improvements
  • Final testing of all the modules and car
  • Collective Test 4: Have the final version of the project tested with all the functionalities
  • 05/22
  • 05/22
  • 05/22
  • 05/22
  • Completed
  • Completed
  • Completed
  • Completed
Week 12
  • 05/25
  • 05/25
  • 05/27
  • 05/27
  • Demo
  • Final Wiki Page Update with addition of all the problems faced during the development
  • 05/25
  • 05/26
  • Completed
  • Completed


Parts List & Cost

Item# Part Desciption Vendor Qty Price($)
1 RC Car Traxxas [1] 1 280
2 CAN Transceivers MCP2551-I/P Comimark [2] 5 8.99
3 Ultrasonic Sensors Max Botix[3] 4 24.95
4 GPS Breakout Board Adafruit[4] 1 29.95
5 GPS Antenna Adafruit[5] 1 19.95
6 RPSMA female to mhf4 Superbat[6] 1 7.99
7 HC05 bluetooth RF Transceiver HiLetgo[7] 1 15.99
8 Triple-axis Accelerometer Adafruit[8] 1 14.95
9 Traxxas RPM Sensor Traxxas[9] 1 13.76
10 Traxxas Battery and Charger Traxxas[10] 1 62.95
11 Voltage Regulator Valefod[11] 6 10.99
12 Headlights Hobbypark[12] 1 7.96


Printed Circuit Board

Initially we started our testing with mounting all our hardware on the breadboard (yes, it was messy and unstable!).

  • Initial_Hardware


PCB Schematic

  • Schematic
  • Final_Board


PCB Board

  • Top_Side
  • Bottom_Side

Challenges

  • Since there are four controllers and a significant number of components (gps, sensors, can transceivers, volt regulator etc.) it was difficult for us to keep our hardware stable because every time we go for field testing some will get disconnected and we were kind of stuck up in the hardware setup.
  • We decided to get the PCB printed but there were some issues and resolving them and getting a new PCB would take time.

Solution

  • Finally we decided to use the prototype board for mounting all the components and stabilizing our hardware.
  • Protoype_Board

CAN Communication

We have used controller area network to broadcast data between the 4 nodes. All nodes are connected to each other through a physically conventional two wire bus. The wires are a twisted pair with 120 Ω resistors at each ends of the bus. 1s and 0s are transmitted as CAN High(0V difference) and Can Low(2v difference). A CAN frame has the following contents:

  • Data Length Code (4bits)
  • Remote Transmission Request.
  • ID extend bit.
  • Message ID (11 bit or 29 bit)
  • Data bytes( depends on DLC)
  • CRC


Arbitration: No two nodes will transmit at the same time because of arbitration. A lower Message-ID has a Higher priority on the CAN bus since 0 is the dominant bit.

Bit Stuffing: CAN bus stuffs extra bits when a long chain of multiple 1's or 0's occur to improve CAN integrity.

DBC File

The DBC file is a simple text file that consists of information for decoding raw CAN bus data to physical values or in human readable form.


Sr. No Message ID Message function Receivers
Driver command
1 300 speed and steering direction for the motor. Motor
2 100 Driver running Motor, Sensor, Geo
Sensor Controller
3 200 Sensor sonars from front, back, left ,right sensor Driver
Motor Controller
4 600 motor speed, motor direction Driver
Geo and Bridge Controller
5 250 Bearing, Heading and Distance Driver
Debug messages
6 Driver Debug SENSOR,MOTOR,GEO_AND_BRIDGE
7 Motor Debug SENSOR,MOTOR,GEO_AND_BRIDGE
8 Sensor Debug SENSOR,MOTOR,GEO_AND_BRIDGE

The ECUs

In this section we will explain the hardware design, logic and challenges faced during development of every node invloved.


Sensor and Bluetooth ECU

Sensor Controller Diagram


Software Design

Technical Challenges

Neighboring Sensor Interference:

Frequent noisy measurements:



Motor ECU

The Motor ECU acts as an encoder for the DC motor (used for propulsion) and Servo motor (used for turning the axle and changing direction of the car). The car is a two wheel drive with DC motor connected to the rear wheels and the servo motor is connected to the front wheels. The DC motor is controlled by Electronic Speed Control. The ECU supplies PWM signal to the ESC and the ESC powers the DC motor. The Servo motor is powered by the car battery as well and gets its PWM signal from the ECU. The RPM sensor sends its output to motor ECU by which the actual speed of the wheels is calculated.

Hardware Design

Hardware Schematic Diagram

ESC & DC Motor

The DC motor is controlled by ESC using PWM signals provided by the motor controller for forward and reverse movements. We used the 9v NiMH battery to power up the ESC. The DC motor is powered by the ESC which has a dc-to-dc converter which converts 9v to 6v. The output from the ESC is used to power the Servo motor. ESC has an ease set button which is used for calibration and setting different modes for the car.

Wires on ESC Description Wire Color
PWM(P2.1) Takes PWM input from SJ2-Board WHITE
VDD(6V) Power Output RED
GND Ground BLACK


The car can be operated in the following 3 modes:
Sport mode(100% Forward, 100% Brakes, 100% Reverse)
Racing mode(100% Forward, 100% Brakes, No Reverse)
Training mode(50% Forward, 100% Brakes, 50% Reverse)

As we needed more than 50% speed for steep ramps, we used Sport mode. The frequency of the PWM signal fed to the servo motor is 100Hz. Based on the duty cycle set by the user, the car will go forward, reverse, or neutral. 10% - 20% duty cycle for reverse. 15% duty cycle for neutral. 15%-20% duty cycle for the forward motion.


Traxxas ESC
Traxxas Brushless DC Motor

Servo Motor

The servo motor we used is Traxxas 2075 which was provided with the car and it is responsible for steering the car. It takes the 6V power directly from ESC. The servo motor is controlled directly from the SJ2 micro-controller board. The PWM signal fed to the servo motor is of frequency 100Hz. Based on the duty cycle of the signal sent to the servo, it rotates in the left / right direction. 10% - 20% duty cycle for left. 15% duty cycle for straight. 15%-20% duty cycle for right.

Wires on ESC Description Wire Color
PWM(P2.0) Takes PWM input from SJ2-Board WHITE
VDD(6V) Power Input RED
GND Ground BLACK
Traxass Servo Motor

RPM Sensor

There are two parts to the RPM sensor - one is the trigger magnet and the other is the sensor. The RPM sensor is used as an input to maintain a constant speed of the vehicle. The sensor mounts on the inside of the gear cover, the trigger magnet mounts on the DC motor shaft. The gear cover and motor shaft need to be removed using the toolkit provided along with the RC car. The procedure is similar to this video, but note that the car used in the video is a 4WD RC car by Traxxas. We made use of the trigger magnet attached to the spur gear to trigger a pulse on the sensor for every rotation of the spur gear. These pulses are then read by the SJ2 board to calculate rotations in a second and later convert it to RPM and MPH. The RPM sensor has 3 wires, the white wire is the output wire that provides the pulses to the SJ2 Board, and the other wires are Supply(6V) and GND. We also used a Pull Down 1K Resistor between Supply and RPM output wires.

Wires on ESC Description Wire Color
GPIO(P0.6) Provides pulses to Motor SJ2-Board WHITE
VDD(6V) Power Input RED
GND Ground BLACK


Traxxas RPM Sensor
Trigger Magnet

Software Design

The motor node acts based on the speed and direction received over CAN bus from the Driver Node. The positive speed values are treated as forward motion and the negative speed values are considered to be the reverse motion of the RC car.

The steering angles are divided into 5-degree segments and the motor node sends the pre-defined pwm duty cycle of the particular segment to the servo motor depending on the angle value received from the driver node.


Speed Control Flowchart

Technical Challenges



Geographical And Bridge Controller

Hardware Design

Software Design

The GEO controller consisted of 4 main parts which are: 1. GPS Module 2. Compass 3.Waypoints Algorithm 4. Geo Logic

The Geo logic takes data from GPS module processes it to get current coordinates, takes data from compass for raw heading. After acquiring data from compass and GPS, it calculates heading , bearing and distance and sends it on CAN bus.

1. GPS Processing

The GPS module uses UART1 to communicate with our SJ2 board. The API call for the GPS driver requires setting up the gps registers to only allow GPGGA data to improve processing. The main API function is called gps__run_once() which digests data from the physical GPS hardware. Inside gps__run_once(), we call two functions that help with parsing the gps coordinates. The first is taking using a line buffer for the UART characters that are digested during operation and checking if they are in fact a full GPGGA string. The second function parses those coordinates from the line buffer and converts them from GPGGA minutes data to polar coordinates. Once the function is called, global static variables located in geo_gps.c are used while a gps__get_coorindate() function is called whenever the API's data wants to be used outside of the gps.c file. In order to check if there is a gps fix, we created a function that checks if certain GPGGA bits are set or not.

2.

Technical Challenges


Driver Node

Driver Node is the master controller. It receives input from sensor and bridge node, processes it to make right decision for controlling the speed and steering direction of the car and then commands the motor node to drive accordingly. This node is also interfaced to the LCD, which acts as dashboard of the car and displays information such as car speed and distance to destination on the screen.

Hardware Design

  • Sjtwo-board
  • LCD Display
  • Driver_Node_Hardware_Connections
  • Software Design

    Technical Challenges



    Mobile Application

    User Interface

    Software Design

    Maps Activity

    Bluetooth/WIFI

    Technical Challenges





    Conclusion

    Project Video

    Project Source Code

    Advise for Future Students

    Acknowledgement

    References

    http://socialledge.com/sjsu/index.php/Industrial_Application_using_CAN_Bus