S15: Touch Navigator

From Embedded Systems Learning Academy
Revision as of 03:24, 24 May 2015 by Proj user4 (talk | contribs) (Hardware Interface)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Project Title

Touch Navigator

Abstract

The purpose of this project is to implement a robot car which will follow the path drawn on the touch screen.

Objectives & Introduction

  • The prime objective of this project is traversing a robotic car autonomously through specific map or grid,depending upon the points drawn on the touchscreen.SJ-ONE board is used giving control signals to motor driver IC and communication between user interface and car. communication between 2 boards is implemented by Embedded baseband wireless protocol using a on-board NORDIC wireless chip .Obstacle sensors are used to detect obstacles and avoid collision.
  • Focus of project was to make an Real-time system/application using touchscreen and SJ-ONE development board which could guide and navigate a vehicle through a specific or predefined area.

Team Members & Responsibilities

  • Athavan Kanagasabapathy
  • James Sushanth Anandraj
  • Ravikumar Vanjara
  • Rishit Borad

Schedule

Week Start Date End Date Task Status Actual Completion Date
1 4/7/2015 4/21/2015 Developing Android Application to communicate to SJOne board over UART Completed Successfully 4/19/2015
2 4/14/2015 4/21/2015 Interfacing the motor with the SJOne and controlling the direction and speed. Completed Successfully 4/21/2015
3 4/21/2015 4/28/2015 Writing application in android to draw paths. Completed Successfully 4/30/2015
4 5/09/2015 5/11/2015 Interfacing with the obstruction sensors. Completed Successfully 5/11/2015
5 4/29/2015 5/4/2015 Mapping traversal area/co-ordinates on the android application. In Progress In Progress
6 5/11/2015 5/--/2015 Integrating the Obstruction detection in main application. In Progress In Progress
7 5/18/2015 5/--/2015 Testing In Progress In Progress

Part List

Sr.No. Parts Cost Useful part links/Datasheets
1 Dual H-Bridge Motor Driver for DC Motor L293D 2.5 $ ST microelectronics Datasheet
2 Car chassis parts - Wheels, shaft, DC motors(2), body 12.0 $ RC Car
3 Batteries/ Power source 5.0 $ Power Bank
4 IR Leds and IR sensor (TSOP38238) 10.0 $ IR sensor Datasheet
5 Antennas for Nordic communication 4.0 $ Router antennas

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Block Diagram

Spring15 244 grp4 blockdiag.png

Hardware Interface

  • SJone Board

The SJ-One Board consists of LPC1758 microcontroller which belongs to the family of ARM Cortex-M3. It operates upto 100MHz clock frequency. ARM Cortex-M3 has a built-in Nested Vectored Interrupt Controller(NVIC) which can support 35 vectored interrupts. It has 512 KB of on-chip flash memory,64Kb on-chip SRAM. The SJ-One board also has a built-in Nordic Wirless device embed on it namely "nRF24L01P", which is used as wireless communication from one board to another board. The board has many accelerated GPIO pins and each of the port pins can be controlled as I/O individually.

  • Nordic wireless

The nRF24L01P is a single chip 2.4GHz transceiver with an embedded baseband protocol engine (Enhanced ShockBurst™), suitable for ultra low power wireless applications. This Nordic wireless device operates at the ISM frequency at the range 2.4 to 2.4835GHz. The design interface between the Nordic wireless device and SJ-One board was established through a Serial Peripheral Interface (SPI) bus. The register map, which is available through the SPI, contains all setup enrolls in the nRF24L01+ and is open in all operation methods of the chip. The wirless communication done by packet-based messgae communication. Internal FIFOs ensure a smooth data flow between the radio front end and the system’s MCU. The radio front end uses GFSK modulation. It has user configurable parameters like frequency channel, output power and air data rate. nRF24L01+ supports an air data rate of 250 kbps, 1 Mbps and 2Mbps. The two power saving modes make the nRF24L01+ very suitable for ultra low power designs.

  • Motor driver
  • Android application

Software Design

Implementation

State Machine

Spring15 244 grp4.png

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

My Issue #1

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.