S14: Virtual Dog

From Embedded Systems Learning Academy
Revision as of 20:31, 24 May 2014 by Proj user16 (talk | contribs) (Hardware Design)

Jump to: navigation, search

Project Title : Virtual Dog - An Object Following Robot

Abstract

In this project, we build a device which would be able to track and follow a particular object. So if suppose that object is you, that device will follow you just like your dog. This tracking and following will be done in two dimensions, i.e. not just forward-backward movement, but left-right also. This can be achieved with the help of two devices, one will be used as reference and other device will continuously keep on monitoring the reference device. If position of reference device changes other device rearranges its position so as to maintain the desired relationship between them.

Objectives & Introduction

The main objective is to build an object following robot, which will follow a particular object in 2-Dimension. To make the robot follow at the same speed as of object we used four DC motor for the four wheels of robot so that it can accelerate the robot to desired speed. To keep track of object movement we used three proximity sensors (20cm-150cm) so that the robot can easily track the object. To power up the robot we used two batteries, one of 5V and other of 12V. 5V battery is used to power up the SJOne Board and 12V battery is required to run the DC motors. We have also implemented an Android App to start/stop robot and read the realtime statistics of sensors and our algorithm. To display the value of sensor as well as decision taken by robot on Android App we used Bluetooth module.

Team Members & Responsibilities

  • Hari
    • Implemented sensor driver and algorithm to normalize sensor values, Android Application.
  • Manish
    • Implemented central control logic and FSM.
  • Viral
    • Implemented motor driver and Motor State Machine, bluetooth driver.

Schedule

Week# Task Estimated
Completion
Date
Status Notes
1 Order Parts 3/16 Partially Completed Not finalized with sensor for distance measurement. Ordered other parts.
2 Sensor Study 3/23 Completed (3/30) Research on sensors took more time than expected due speed constrains of sensors conflicting with our requirement. Finally decided to move with IR proximity sensor. Sensors ordered.
3 Sensor Controller Implementation 3/30 Completed (4/6) Three sensors interfaced with on board ADC pins. Controller implemented to determine direction of movement based on those three sensors
4 Servo and Stepper Motor Controller Implementation 4/6 Completed (4/6) Initially planned to use stepper motor for steering and servo to move robot. But due to power constraints, decided to use DC motors to make a 4WD robot. Controller implemented to move and turn robot based on differential wheel speeds.
5 Central Controller Logic Implementation 4/13 Completed (4/13) Integrated both controllers and developed basic logic to control wheels based on sensor input.
6 Assembly and Building Final Chassis 4/20 Completed (4/20) Mounted all hardware parts on chassis to make a standalone robot. Central controller logic is still tuning.
7 Unit Testing and Bug Fixing 4/27 Completed (5/4) Tested various combinations of object movement and tuned our algorithm accordingly. Tuning of algorithm took more time than expected because of many corner cases.
8 Testing and Finishing Touch 5/4 Completed (5/11) Faced strange problem at final stages. Earlier sensors were giving linear output for distance v/s ADC value. Over the period we realized that our robot is not following the way it used to follow earlier. So we need to calibrate distance v/s ADC value again, and based on that we required to change our algorithm.
9 Android Application using Bluetooth N/A Completed (5/22) Developed an Android Application through which we can start and stop our robot and able to collect realtime data for sensor values as well as decisions taken by robot.

Parts List & Cost

# Part Description Quantity Manufacturer Part No Cost
1 SJOne Board 1 Preet $80.00
2 IR Distance Sensor (20cm - 150cm) 3 Adafruit GP2Y0A02YK $47.85
3 DC Motor (12V) 4 HSC Electronics $6.00
4 Wheels 4 Polulu $8.00
5 Battery 5V/1A 10000mAh 1 Amazon $40
6 Battery 12V/1A 3800mAh 1 Amazon $25
7 LM2938D (Motor Driver IC) 2 HSC Electronic $5.40
8 Chassis 2 Walmart $12.00
9 Accessories (jumper wires, nut-bolts, prototype board, USB socket) $20.00
10 RN42-XV Bluetooth Module 1 Sparkfun WRL-11601 $20.95
Total (Excluding Shipping and Taxes) $265.20

Design & Implementation

Hardware Design

CmpE244 S14 vDog system block diagram.bmp
The Hardware unit consist of three proximity sensor, SJOne board, four DC motor, bluetooth module,chassis and for wheels. All the three proximity sensor will measure their respective analog value and send it to the ADC pin of the SJOne board which will convert it to the digital value,the convert digital value will be utilized to determine the distance between the robot and the object. Based on the calculated distance the PWM value is determine for each DC motor, these PWM value is given as input to the DC motor via L293D IC. The Bluetooth device will read the value of the sensor from the SJOne board through UART and send it to the Android App which will display the real time value of the sensor as well as decision taken by robot.

DC Motor

CmpE244 S14 vDog DC motor.png
We are using four DC motor for our project, the DC motor we are using has following rating 5-12V, 0.16Amp, 2000RPM. We are using DC motor so that we can provide 360 degree rotation to our robot wheel as well as it can help to drive the robot at a very high speed.

Proximity Sensor

CmpE244 S14 vDog IR sensor.png
This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine how close the nearest object is. These sensors are good for detection between 20cm-150cm.

LM293D IC

CmpE244 S14 vDog L293D.png
L293D is a typical Motor driver or Motor Driver IC which allows DC motor to drive on either direction. L293D is a 16-pin IC which can control a set of two DC motors simultaneously in any direction. It means that you can control two DC motors with a single L293D IC.

Bluetooth Module

CmpE244 S14 vDog bluetooth device.png
The RN-42 is compatible with the Bluetooth versions 2 and below. The advantage of using this module is it's low power and at the same time can provide a good data rate. This provides a high performance on chip antenna where data rates upto 3Mbps are transferred. The disadvantage is that, it has a very less distance which is approximately 20 meters. There is a pull up circuit of 1k to the Vcc. This is provided so that if the input power supply has instability or tends to bounce which causes the that device to be damaged. There is separate pin allocated for the Factory Reset such that this comes into the picture when the module is misconfigured. The toggle of the specific GPIO pins indicate the status of the module. When toggled at 1Hz, the module is discoverable and is waiting for a connection. When at 10Hz, it made to change to the command mode. If it is very low, then module is already connected to another device over the bluetooth.

Hardware Interface

Pin connections for IR sensor through ADC:
CmpE244 S14 vDog sensor connections.bmp

Pin connections for Motor Driver using PWM:
CmpE244 S14 vDog motor connections.bmp

Pin connections for Bluetooth Device for Andoird App
CmpE244 S14 vDog bluetooth connections.bmp

Software Design

State Machine Diagram
CmpE244 S14 vDog state machine.bmp
Startup Process Flowchart
CmpE244 S14 vDog flowchart startup.bmp
On Start of the ROBOT, the ADC is initialised for the reading the data. This is used to calculate which zone the object lies. Based on this decision, the robot has to decide whether it should follow, stop or turn in any other direction. This is performed by initialising the PWM. If any other obstacle comes in between the range of the object and the robot, then the buzzer is activated and hence buzz sound is produced. The Bluetooth for the UART is initialised so that this is used for the communication between the Android application and ROBOT. With the help of the Application the Robot is started. This activates the sensor task so that data is read from all the three sensors. Based on the sensor readings and after the normalization of the data read, decision is made on which direction the Robot should move. Using the Motor Driver Task and with the help of the decision made, the motors are made to rotate in the appropriate direction. Finally, the values and the direction which are decided are sent to the Bluetooth task. This task functions in transmitting and receiving the data to the android application. This application also used to start and stop the robot.

Sensor Driver Flowchart
CmpE244 S14 vDog flowchart sensor.bmp
In the Sensor Driver Task, the sensor values from all the three proximity sensors are read. They are normalized by using calculating the mean of the previous 30 sensor values. Based on this, the object position is determined. If the object is located in the Zone 1 of the middle sensor, then the finite state machine is changed to reverse. The robot moves until the original position is achieved. If the object is located in the Zone 3 and Zone 4 of the middle sensor, then finite state machine is moved to the Forward state which causes the robot to move forward. The left sensor detects the object if it is in Zone 1 and Zone 2. Based on the decision, the finite state machine is changed to reverse right. This moves the robot in the reverse right direction causing the direction of the robot to turn left. The right sensor detects the object if it is in Zone 1 and Zone 2, and the finite state machine is moved to the reverse left. This causes to change the direction of the robot to the right. The left sensor detects the object if it is in Zone 3 and Zone 4. Based on the decision, the finite state machine is changed to forward left. This moves the robot in the forward and left direction causing the direction of the robot to turn left. The right sensor detects the object if it is in Zone 3 and Zone 4, and the finite state machine is moved to the forward right. This causes to change the direction of the robot to the right. Thus based on the sensor values, the next stage of the Finite State Machine is decided and moves to that particular state.

Motor Driver Flowchart
CmpE244 S14 vDog flowchart motor.bmp
In the Motor Driver task, the finite state machine is read for each entry of the sensor data. Based on the state machine the Robot decides on the direction to move. If the decision made is forward, then the front two wheels which are connected to the driver are made to move. This causes the device to move forward. If it is forward left, then the front left wheel’s speed is decreased. This causes the device to turn left. If it is forward right, then the front right wheel speed is decreased. This causes the device to turn left. If the decision made is reverse, the wheels are made to rotate in the opposite direction. If it is reverse left, then the back left wheel’s direction is opposite and the speed is decreased. This causes the device to turn reverse left. If it is reverse right, then the back right wheel’s direction rotates in the opposite direction and the speed is decreased. This causes the device to turn reverse right. With the help of all the decisions, the Robot can be made to rotate 360 degree making the Robot to detect the object’s range and moving in appropriate direction. Finally, after Robot has moved such that the object comes into the ZONE_2, all the state machines are reset. This loop occurs until there is an indicator received telling the Robot to stop.

Implementation

Proximity Sensor:
To determine the distance of object from robot with the help of proximity sensor we follow the below steps.
1. The proximity sensor detect the object present in front of it, based on object distance from it, it generate the analog value.
2. The analog value is given as input to ADC which converts this analog value to digital value.
3. Based on the digital value of all the three sensors a normalized algorithm is used which calculate the exact distance of object from sensor.

DC Motor:
To move the robot in a particular direction based on object movement we follow the below steps.
1. Based on the calculated distance from proximity sensor the PWM value is given to different motor.
2. The PWM act as input to the motor via L293D IC, based on this value the motor will accelerate.

Bluetooth Module:
To display the sensor value as well as decision taken by the robot on Android Application we follow the below steps.
1. The sensor value as well as decision taken by robot is send to the Bluetooth UART pin by the UART present on the SJOne board.
2. The UART of the Bluetooth send the data it received wirelessly to the Android device to which it is connected.
3. The Android Application display the data it received wirelessly from the Bluetooth module to which it is connected.

Movement of robot according to the movement of object:
CmpE244 S14 vDog range zones.bmp
When the object which the robot is following is in ZONE_CLOSE range with respect to middle sensor than the robot will move backward, when the object is in ZONE_IN range with respect to middle sensor than the robot will remain in stationary state, when the object is in ZONE_FAR range with respect to middle sensor than the robot will move forward and start following the object, when the object is in ZONE_TOO_FAR range with respect to middle sensor than the robot will move towards the object at very high speed. When the object is in ZONE_OUT_OF_RANGE than the robot will remain stationary and will notify that the object is out of range.
When the object tries to take left/right turn than it will move ZONE_OUT_OF_RANGE with respect to middle sensor but the left or right sensor will detect the object and move the robot accordingly till it come in ZONE_IN range with respect to middle sensor.

LED conventions:

The four LED’s present on the SJOne Board indicate the movement of the robot in the following way:


CmpE244 S14 vDog LED 01.png
When the 1st and 4th LED is blinking simultaneously very fast than the robot is at stationary state and it is waiting for the object to come in its range i.e. object is in ZONE_OUT_OF_RANGE.


CmpE244 S14 vDog LED 02.png CmpE244 S14 vDog LED 03.png
When the 1st and 4th LED and 2nd and 3rd LED are blinking alternately than it indicate the object is in ZONE_IN range.


CmpE244 S14 vDog LED 04.png
When the 1st and 4th LED is blinking simultaneously than it indicates that the robot is moving in REVERSE direction so the object is in ZONE_CLOSE range.


CmpE244 S14 vDog LED 05.png
When the 2nd and 3rd LED is blinking simultaneously than it indicates that the robot is moving in FORWARD direction so the object is in ZONE_TOO_FAR or ZONE_FAR range.


CmpE244 S14 vDog LED 06.png
When the 3rd and 4th LED is blinking simultaneously than it indicates that the robot is taking RIGHT turn so that the robot can come in ZONE_IN range with respect to object.


CmpE244 S14 vDog LED 07.png
When the 2nd and 1st LED is blinking simultaneously than it indicates that the robot is taking LEFT turn so that the robot can come in ZONE_IN range with respect to object.


CmpE244 S14 vDog LED 08.png
When only 4th LED is blinking than it indicates that the robot is taking BACK RIGHT turn so that the robot can come in range with respect to object.


CmpE244 S14 vDog LED 09.png
When only 1st LED is blinking than it indicates that the robot is taking BACK LEFT turn so that the robot can come in range with respect to object.


CmpE244 S14 vDog LED 10.png
When all the four LED is blinking simultaneously than it indicate that the robot has detect some obstacle in its range.


Virtual DOG Android Application:

The Android application helps in communicating with the Bluetooth Module. The Bluetooth module is RN- 42. This module is directly placed over the location over the zigbee module on the LPC board. Communication between the devices is full duplex. The Initiation and the Termination of the Robot is controlled from the Android application.

On opening application, the Bluetooth has to be turned ON. There are two Buttons for turning the Bluetooth ON and OFF. For the Bluetooth to be turned ON, permissions are required from the Root User. If the authentication is performed, then the devices which are available in the range of the Bluetooth module are listed down using the discovery method of the device. The Module’s name is selected in the mobile. The devices are paired together using a key. The key provides the security feature over the transmission and reception.

CmpE244 S14 vDog android flowchart.png

There are two buttons. The ‘START’ and ‘STOP’ button which indicate the Robot to turn ON and OFF. This button is created in the XML. This language is used to build the UI functionalities. On clicking the START button, data is written to the Robot in order to indicate the Start status. The Robot starts sensing and sends the back the values along with the direction in which it moves. This is sent in the form as a metadata, so that the time taken for transmitting is less. This improves the performance. The Metadata which comprises of the sensor values and the direction is received until the stop button is pressed. A separate data is written for stopping the data. The Robot shuts down on receiving the data.

In order to connect to the Robot faster, a separate list has been created which maintains the list of the paired devices. This will show the devices which were connected previously.

There is a new fragment (page) created from the MainActivity which is created and the device is opened with that new fragment. On successful completion of the pairing, there are some threads which are made to run in the background. On creation of the instance of the new fragment page, a thread to read the data on the output stream runs as one of the background process. This buffer which is read should happen continuously until there is ‘\n’ or ‘\r’ character is read. If it read, then the data from the UART of the module is read.


Application Screenshots:

CmpE244 S14 vDog android app 01.pngCmpE244 S14 vDog android app 02.png

Actual Implementation Images:

Robot Top View:
CmpE244 S14 vDog top view.png

Robot Side View:
CmpE244 S14 vDog side view.png

Robot Front View:
CmpE244 S14 vDog front view.png

Testing & Technical Challenges

Motor Selection:
Stepper Motor:
Initially we plan to use the Stepper motor with our DC motor so that we can control the position of our robot very precisely. As the servo motor that we plan to use is very heavy due to which our chassis weight get increased to a extreme level, and there is torque degradation at higher speed in stepper motor which is not desirable for our project so we plan to drop the use of stepper motor.
Servo Motor:
Initially we plan to use the Servo motor instead of DC motor for our project so that we can provide a high torque to our robot wheels, but due to some disadvantage of servo motor like it continue to draw a high current when it is stuck at particular position make it undesirable for our project.
DC Motor:
Finally we select the DC motor instead of using Stepper motor and Servo Motor. There are some advantages of DC motor like they can run at very high RPM value, provide full rotation , continue to rotate until power is removed, can be easily controlled using PWM. This advantage of DC motor matches with the requirement of the motor that we are looking for our project.

Sensor Selection:
Nordic Wi-Fi:
Initially we plan to use Nordic Wi-Fi present on our SJ One board to calculate the distance between robot and the object so that accordingly we can change the position of the robot. When we perform the experiment between to Nordic Wi-Fi and tried calculating the distance between them the outcome result were not favourable, we were negligible change in the value when we change the position of one Wi-Fi module with respect to other. The outcome results were not desirable for our project so we drop the idea of using the Wi-Fi module.
Ultrasonic Sensor:
After getting the undesirable result from Wi-Fi we plan to use ultrasonic sensor to calculate the distance between the object and robot. When we perform the experiment the outcome result were not favourable, though the range of ultrasonic sensor was too good but the beam angle it generates to detect the object which come under its range was too high due to which it was able to detect a large number of object, so we were not able to calculate the exact distance between the original object and the robot. So we plan to drop the idea of using Ultrasonic Sensor.
Proximity Sensor:
We than plan to use the proximity sensor to calculate the distance between the object and robot. The proximity sensor we used to perform the experiment has a range of 20cm to 150cm, the outcome result from the experiment were favourable. We were able to calculate the exact distance between the robot and the object. So we decide to use the proximity sensor for our project to calculate the distance between robot and object.

Motor Calibration Issue:
As we decided to use DC motor for our project by performing a number of experiments, we plan to use 4 DC motor one for each wheel of the robot. After connecting DC motor to the wheels of the robot we check the alignment of all the four wheels, if they were not alignment we make all of them align by performing a number of hit and trial methods. The next issue is to run each motor at different speed at the same input given voltage so that we can control and move our robot in any direction. All the four motor speed is control individually by calculating the separate PWM value for each motor.

Sensor Calibration Issue:
As we decide to use proximity sensor for our project we have to solve a number of calibration issue related with this sensor. The first thing is we have to decide the number of sensor required for our project. We decided to begin our experiment using three sensors, the next thing we have to decide is the position where we can place these sensor on our robot. After performing a lot of experiment we found that if our target object comes in a range less than 20cm from our robot all the sensor start throwing from garbage value. So we decided to place the sensor at the back of robot with their face facing front so that the sensor will not through garbage values if the target object is very close to the robot. Now we have to decide the angle at which our sensor must be placed so that it can detect the target object anywhere between the angles of 0 to 180 degree. So after performing a number of experiments we place our sensor at 45, 90 and 135 degree. After placing the sensor at the proper position the next thing we have to determine is the direction in which our robot will move based on the sensor values. For this we use the normalization method on the sensor value so that we can predict the correct direction in which we have to move our robot.

Android Application Issue:
Operations involving the UI have the high Priority in the Android. Because of this, Updating the text Box with the sensor values and the direction will throw an IOexception. Because of this the application crashes.
Solution: Let the thread involving the receive function be executing as the background process and the UI update shall happen only after the execution of the receiving function.
Establishing the initial pairing between the devices caused some faults such as socket was not open or already read.
Solution: This was due to the sudden termination of the previous socket connection. The Socket has to be closed on Application exit, on all the catch exceptions and any sudden termination.

Conclusion

The Virtual Dog was a very challenging and research oriented project. Detailed analysis were made on various sensors while trying to implement the project.
The project was built on a small scale. This would work as a prototype to build the applications such as shopping cart following a person in crowded areas such as the grocery stores etc.

Project Video

Upload a video of your project and post the link here.

Project Source Code

Send me your zipped source code and I will upload this to SourceForge and link it for you.

References

Acknowledgement

The hardware components were made available from Amazon,Sparkfun, Adafruit. Thanks to Preetpal Kang for providing right guidance for our project.

References Used

LPC_USER_MANUAL
RN-42 Data Sheet
Socialledge Embedded Systems Wiki
L293D Data Sheet
IR Sensor Data Sheet