S15: Protocol Interface: I2C - CAN Bridge
Contents
Serial Protocol Convertor
Abstract
This project is aimed at developing a device, which is able to convert the incoming data from one protocol to another (I2C, UART, SPI, CAN). In a system operating over a CAN architecture, there is a need of an inbuilt CAN peripheral interface in every controller. Because of hardware limitations, many controllers do not support the CAN peripherals; therefore they are restricted to communicate over the limited number of protocols. This device provides a flexibility to the designers so that they can choose any communication protocol at the input, and convert the data to the desired protocol.
Objectives & Introduction
Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.
Team Members & Responsibilities
- Ishan Bhavsar
- <role>
- Tej Kogekar
- <role>
- Rutwik Kulkarni
- <role>
- Mitesh Sanghvi
- <role>
Schedule
Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.
| Sl. No | Start Date | End Date | Task | Status | Actual Completion Date |
|---|---|---|---|---|---|
| 1 | 03/08/2015 | 03/14/2015 | Develop drivers for GPIO and interrupt based UART | Completed | 03/14/2015 |
| 2 | 03/15/2015 | 03/21/2015 | Develop driver for interrupt based SPI | Ongoing | YTD |
| 3 | 03/22/2015 | 03/28/2015 | Develop driver for interrupt based I2C | Completed | 03/28/2015 |
| 4 | 03/29/2015 | 04/04/2015 | Develop driver for CAN (using API) and Study of FreeRTOS Queues | Ongoing | YTD |
| 5 | 04/05/2015 | 04/11/2015 | Develop algorithms for controlling SPI and I2C devices through UART, SPI, CAN and I2C controllers | Ongoing | YTD |
| 6 | 04/12/2015 | 04/18/2015 | Develop algorithms for controlling UART and CAN devices through UART, SPI, CAN and I2C controllers | Scheduled | YTD |
| 7 | 04/19/2015 | 04/25/2015 | Develop algorithms for controlling Bluetooth device through UART, SPI, CAN and I2C controllers | Scheduled | YTD |
| 8 | 04/26/2015 | 05/02/2015 | Develop hardware for configuring input and output from UART, SPI, CAN, I2C and Bluetooth | Scheduled | YTD |
| 9 | 05/03/2015 | 05/09/2015 | Final Testing | Scheduled | YTD |
Parts List & Cost
Give a simple list of the cost of your project broken down by components. Do not write long stories here.
Design & Implementation
The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.
Hardware Design
Discuss your hardware design here. Show detailed schematics, and the interface here.
Hardware Interface
In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.
Software Design
Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.
Implementation
This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.
Testing & Technical Challenges
Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.
Include sub-sections that list out a problem and solution, such as:
My Issue #1
Discuss the issue and resolution.
Conclusion
Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?
Project Video
Upload a video of your project and post the link here.
Project Source Code
References
Acknowledgement
Any acknowledgement that you may wish to provide can be included here.
References Used
List any references used in project.
Appendix
You can list the references you used.
