Difference between revisions of "S16: Ahava"

Revision as of 00:59, 22 May 2016

VisionCar

This project aims at tracking a known object from a vehicle and follow the target at a pre-fixed distance. The RC car is mounted with a camera which is interfaced to a Raspberry Pi Compute module. The Compute module performs the required image processing using OpenCV and provides relevant data to the Car Controller for driving. An Android Application is developed to allow a user to select an object by adjusting the HSV filter thresholds. These values are then used by the imaging application to track the desired object.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

Aditya Devaguptapu

Ajai Krishna Velayutham

Akshay Vijaykumar

Hemanth Konanur Nagendra

Vishwanath Balakuntla Ramesh

Schedule

Week#	Date	Task	Actual	Status
1	3/27/2016	Selection of platform for Mono / Stereo Vision processing. Completion of PWM API Documentation.	To confirm on suitable platform for Mono / Stereo Vision processing. To understand the PWM signals transmitted from the RCU for driving the car motors.	Completed
2	4/03/2016	To decide on suitable algorithm for Object Detection and Depth Perception. Establishing direction and speed control on the car. Order components.	Decided on disparity mapping for depth perception. Pending work is camera setup and calibration for this purpose. Direction and speed control of the car is completed	In Progress
4	4/20/2016	Implementation of Imaging Algorithm and Testing on a PC Environment. Complete setup of Open CV library and verification of video streaming on the development platform. Decision on Bluetooth or kill-switch implementation for car control.	PC setup and testing is in progress. OpenCV is setup and running on the platform. Pending - Stream data from the cameras	In Progress
5	4/27/2016	Mounting controllers and cameras on the car. Complete Imaging and verification on the board.		Incomplete
6	5/04/2016	Integrating Imaging results with the car controls.		Incomplete
7	5/11/2016	Testing car integrated with control signals and perform calibrations.		Incomplete
8	5/18/2016	Final Testing and Enhancements.		Incomplete

Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Design & Implementation

Hardware Design

System Architecture

Power Distribution Unit

Connection Matrix

Car Control

Motor Interface

Bluetooth Interface

Image Processing

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

My Issue #1

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

Sourceforge Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.

@@ Line 101: / Line 101: @@
 ===== Motor Interface =====
 ===== Bluetooth Interface =====
-===== Image Processing =====
+==== Image Processing ====
 === Software Design ===