Difference between revisions of "S16: OpenSJ Bluz"

Revision as of 20:52, 1 May 2016

Grading Criteria

How well is Software & Hardware Design described?
How well can this report be used to reproduce this project?
Code Quality
Overall Report Quality:
- Software Block Diagrams
- Hardware Block Diagrams
  Schematic Quality
- Quality of technical challenges and solutions adopted.

OpenSJ Bluz

Abstract

This section should be a couple lines to describe what your project does.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

Dhruv Kakadiya
Surojit Sengupta

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Team Schedule

SI No.	Start Date	End Date	Task	Team Member	Status	Actual Completion Date
1	03/12/2016	03/22/2016	Understanding the requirements and having initial team discussions on approach to be followed to carry out project Forming sub-teams and assigning individual modules to each sub-team	-	Completed	03/21/2016
2	03/22/2016	03/27/2016	Following up on hardware components procurement through team discussions, PCB design	Dhruv	Completed	03/26/2016
3	03/27/2016	03/29/2016	Finding out a way to program Bluefruit Module using SW(serial wire) interface.	Dhruv	Completed	03/30/2016
4	03/29/2016	04/1/2016	Implement HRS(Heart Rate Sensor) Profile on BlueFruit Module	Dhruv, Surojit	Completed	04/1/2016
5	04/1/2016	04/4/2016	Implement Nordic UART Service to send and receive data from UART ( Wireless UART ) and check communication using Nordic Master Control Panel Application	Dhruv, Surojit	Completed	04/4/2016
6	04/4/2016	04/10/2016	Create individual BLE profile for each sensor (Accelerometer, Temperature, Light etc.)	Dhruv, Surojit	Completed	04/12/2016
7	04/10/2016	04/25/2016	Create simple BLE Android application to receive sensor data in appropriate BLE service	Dhruv, Surojit	Incomplete	-
8	04/25/2016	04/30/2016	Create user defined GATT services and broadcast individual sensor data in individual services and plot real time graphs on Android	Surojit	Incomplete	-
9	04/30/2016	05/10/2016	PCB and Firmware testing and debugging, Pushing all data to the cloud	Dhruv, Surojit	Incomplete	-

Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Item#	Part Desciption	Vendor	Qty	Cost
1	Bluefruit UART BLE Module	Adafruit	1	$23.75
2	SJOne board	CmpE Department	1	$80
3	nRF51DK	Mouser	1	$39
	Total Cost			$150

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Technical Specifications for Bluefruit BLE module

Nordic nRF51822 - ARM Cortex M0 core running at 16MHz
256KB flash memory
32KB SRAM
Peak current draw <20mA (radio actively transmitting/receiving)
Transport: UART typically @ 9600 baud with HW flow control (Configurable)
5V-safe inputs
On-board 3.3V voltage regulation
Bootloader with support for safe OTA firmware updates
Supports Central and Peripheral mode
Supports Bluetooth Smart protocol stacks
On air compatible with nRF24L series

Front side breakouts

Bluefruit module front pin outs

Power pins

VIN - This is the power supply for the module, supply with 3.3-16V power supply input. This will be regulated down to 3.3V to run the chip
GND - The common/GND pin for power and logic

UART pins

TXO - This is the UART Transmit pin out of the breakout (Bluefruit LE --> SJOne), it's at 3.3V logic level.
RXI - This is the UART Receive pin into the breakout (SJOne--> Bluefruit LE). This has a logic level shifter on it, you can use 3-5V logic.
CTS - Clear to Send hardware flow control pin into the the breakou (SJOne--> Bluefruit LE). Use this pin to tell the Bluefruit that it can send data back to the SJOne over the TXO pin. This pin is pulled high by default and must be set to ground in order to enable data transfer out! If you do not need hardware flow control, tie this pin to ground it is a level shifted pin, you can use 3-5V logic
RTS - Read to Send flow control pin out of the module (Bluefruit LE --> SJOne). This pin will be low when its fine to send data to the Bluefruit. In general, at 9600 baud we haven't seen a need for this pin, but you can watch it for full flow control! This pin is 3.3V out

Other pins

MOD - Mode Selection. The Bluefruit has two modes, Command and Data. You can keep this pin disconnected, and use the slide switch to select the mode. Or, you can control the mode by setting this pin voltage, it will override the switch setting! High = Command Mode, Low = UART/DATA mode. This pin is level shifted, you can use 3-5V logic
DFU - Setting this pin low when you power the device up will force the Bluefruit LE module to enter a special firmware update mode to update the firmware over the air. Once the device is powered up, this pin can also be used to perform a factory reset. Wire the pin to GND for >5s until the two LEDs start to blink, then release the pin (set it to 5V or logic high) and a factory reset will be performed.

Reverse side breakouts

Reverse side pin outs for Bluefruit module is as per below.

Bluefruit module back pin outs

Opt VBat - If you fancy, you can solder on a JST 2-PH connector, this will let you easily plug in a Lithium Ion or other battery pack. This connector pad is diode protected so you can use both Vin and VBat and the regulator will automatically switch to the higher voltage

Opt. 32 KHz - If you're doing some funky low power work, we wanted to give you the option of solderin in a 32khz oscillator. Our firmware doesn't support it yet but its there!

SWC - This is the SWD clock pin, 3v logic - for advanced hackers!

SWD - This is the SWD data pin, 3v logic - for advanced hackers!

3Vo - This is the output from the 3V regulator, for testing and also if you really need regulated 3V, up to 250mA available

FCR - This is the factory reset pin. When all else fails and you did something to really weird out your module, tie this pad to ground while powering up the module and it will factory reset.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Needed Software tools to program nRF51822 Bluefruit module

nRFgo Studio
nRF51 Software Development Kit (SDKv8.0.0)
Keil IDE
S110 nRF51822 SoftDevice
S110 SoftDevice programming tools
Nordic Master Control Panel Android/iOS application
Segger J-Link Programmer

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Software UART Configuration

Bluefruit Pin Connection Table
Description	Interface	Bluefruit Port	SJOne Board Port
Supply Voltage	N/A	Vcc	3.3 V
Ground	N/A	GND	GND
Bluefruit Module	UART3	P0.10 -> Rx P0.9 -> Tx	Channel 1 -> TxD3 Channel 2 -> RxD3
MODE	Data/Command mode selection	MOD	P2.0
DFU select	Device Firmware Update	DFU	P2.1

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

UART Communication Challenge

Problem - Tried to communicate between SJOne and Bluefruit module over UART interface with built-in firmware, but not able to receive data correctly as HW flow control was enabled in Nordic firmware.
Solution - Flashed new firmware in Nordic module with turning off HW flow control for UART interface.

nRF51822 Firmware Update Challenge

Problem - Updated inbuilt firmware which comes with Bluefruit module using Device Firmware Update service to turn off hardware flow control in UART interface, it updates successfully but then that firmware was not working as expected because of crystal settings which are being used for Bluetooth Softdevice drivers.
Solution - DFU service was not available to use as we have updated firmware with wrong settings so need to upload now new firmware using Serial Wire Debug Programmer. Then we have updated new firmware with crystal settings "NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION" (On chip Low Frquency Crystal) using nRFGoStudio Software. Then each time we have used SWD programmer to flash any new version of firmware.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

GitHub Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.

Scratch pad

1. Collect sensor data from all the sensors a. IMU b. Temp c. Light

Collect values and transmit over individual BLE service nrf51822 -> no OS. Put OS on top of that and replace NORDIC BLE UART , with own ble service and use specific UUID

Profiles ->

Light Sensor (Notify/Indicate/Raw read)

Reading for BLE overview - http://mbientlab.com/blog/bluetooth-low-energy-introduction/

BLE Part https://www.adafruit.com/product/2479

Try and implement FreeRTOS / RTX on the AdaFruit BLE nordic Part

Surojit - Start with the Android side of things [04/23/2016] ==> Balance a ball based on mobile app based on IMU reading from board. ==> Real time graph for each of the Sensor Readings. ==> Push data on to cloud

Dhruv- 1 sensor and BLE nordic and tune it , Make BLE profile (Temperature) [04/23/2016]
Dhruv- 1 more sensor and BLE nordic , Make BLE profile (Light) [04/23/2016]
Surojit - 1 more sensor and BLE nordic , Make BLE profile (IMU) [04/17/2016]
Dhruv - FreeRTOS [04/23/2016]

Extra Credit Over the Air Update (OTA)

@@ Line 267: / Line 267: @@
 Include sub-sections that list out a problem and solution, such as:
-=== nRF51822 Firmware Update Issue ===
+=== UART Communication Challenge ===
+* '''Problem''' - Tried to communicate between SJOne and Bluefruit module over UART interface with built-in firmware, but not able to receive data correctly as HW flow control was enabled in Nordic firmware.
+* '''Solution''' - Flashed new firmware in Nordic module with turning off HW flow control for UART interface.
+=== nRF51822 Firmware Update Challenge===
 * '''Problem''' - Updated inbuilt firmware which comes with Bluefruit module using Device Firmware Update service to turn off hardware flow control in UART interface, it updates successfully but then that firmware was not working as expected because of crystal settings which are being used for Bluetooth Softdevice drivers.
 * '''Solution''' - DFU service was not available to use as we have updated firmware with wrong settings so need to upload now new firmware using Serial Wire Debug Programmer. Then we have updated new firmware with crystal settings '''"NRF_CLOCK_LFCLKSRC_RC_250_PPM_250MS_CALIBRATION"''' (On chip Low Frquency Crystal) using nRFGoStudio Software. Then each time we have used SWD programmer to flash any new version of firmware.