Difference between revisions of "User:Proj user9"

From Embedded Systems Learning Academy
Jump to: navigation, search
(Replaced content with "This is your user page; please do not write your report at this article.")
 
(4 intermediate revisions by one other user not shown)
Line 1: Line 1:
=== Grading Criteria ===
+
This is your user page; please do not write your report at this article.
<font color="green">
 
*  How well is Software & Hardware Design described?
 
*  How well can this report be used to reproduce this project?
 
*  Code Quality
 
*  Overall Report Quality:
 
**  Software Block Diagrams
 
**  Hardware Block Diagrams
 
**:  Schematic Quality
 
**  Quality of technical challenges and solutions adopted.
 
</font>
 
 
 
== Project Title ==
 
Bulb Ramper
 
 
 
== Abstract ==
 
 
 
Time-lapse photography is the process of taking many exposures over a long period of time to produce impressive short videos and photos, which create a feeling of traveling quickly through time. While the ability to create time-lapse videos or photos is available to anyone with a camera and a fairly inexpensive with a trigger controller, the ability to increase exposure time (bulb ramping) while moving the camera is not. Moving bulb-ramping device currently on the market cost hundreds of dollars.  Our team intends to create a bulb-ramping device that can rotate 360 degrees around and, will trigger the camera shutter in sync with travel and will also have the ability to pan as it travels.
 
 
 
== Objectives & Introduction ==
 
Show list of your objectives.  This section includes the high level details of your project.  You can write about the various sensors or peripherals you used to get your project completed.
 
 
 
=== Team Members & Responsibilities ===
 
*  Team Member 1
 
**  Driver Development
 
*  Team Member 2
 
**  FreeRTOS Software Design
 
 
 
== Schedule ==
 
Show a simple table or figures that show your scheduled as planned before you started working on the project.  Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals.  The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.
 
 
 
{| class="wikitable"
 
|-
 
! scope="col"| Week#
 
! scope="col"| Date
 
! scope="col"| Task
 
|-
 
! scope="row"| 1
 
| 10/8
 
| Task list
 
|}
 
 
 
== Parts List & Cost ==
 
Give a simple list of the cost of your project broken down by components.  Do not write long stories here.
 
 
 
== Design & Implementation ==
 
[[File:Project Flow.jpg]]
 
 
 
The software flow is detailed up top. The general flow has the user setting each variable (# of pictures to take, motor movement, shutter time, etc). After which, the program will automatically take pictures and move on their own until the required pictures have been taken.
 
 
 
As part of the flow process, there is a loop that is repeated in order to repeatedly take pictures and move the camera platform.
 
 
 
=== Hardware Design ===
 
[[File:camera_circuit.jpg]]
 
The circuit interface to the camera is displayed above. To the right is the stereo jack that is connected to the camera N3 port.
 
 
 
It has three distinct parts:
 
1. Ring: When energized from the opto-coupler, this will cause the camera to focus (Will simulated half press of the camera)
 
2. Tip: When energized from the opto-coupler, this will cause the camera to open the shutter
 
3. Sleeve: The ground of the system
 
 
 
The 220 ohm resistor has been selected to provide ~15mA (3.3v GPIO out from SJSU board divide by 220 ohm) going into 4N35 opto-coupler. The purpose of the opto-coupler is to transfer electrical signals between two isolated circuits by using light. This serves as a protecting mechanism to prevent high voltage from going into the camera.
 
 
 
[[File:optocoupler.jpg]]
 
 
 
 
 
Picture of 4N35 in our hardware:
 
 
 
[[File:photodiode.jpg]]
 
 
 
=== Hardware Interface ===
 
In this section, you can describe how your hardware communicates, such as which BUSes used.  You can discuss your driver implementation here, such that the '''Software Design''' section is isolated to talk about high level workings rather than inner working of your project.
 
 
 
=== Software Design ===
 
Show your software design.  For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level.  Do not show the details of the code.  For example, do not show exact code, but you may show psuedocode and fragments of code.  Keep in mind that you are showing DESIGN of your software, not the inner workings of it. 
 
 
 
=== Implementation ===
 
This section includes implementation, but again, not the details, just the high level.  For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash.  You can include sub-sections for each of your component implementation.
 
 
 
== Testing & Technical Challenges ==
 
Describe the challenges of your project.  What advise would you give yourself or someone else if your project can be started from scratch again?
 
Make a smooth transition to testing section and described what it took to test your project.
 
 
 
Include sub-sections that list out a problem and solution, such as:
 
 
 
=== My Issue #1 ===
 
Discuss the issue and resolution.
 
 
 
== Conclusion ==
 
Conclude your project here.  You can recap your testing and problems.  You should address the "so what" part here to indicate what you ultimately learnt from this project.  How has this project increased your knowledge?
 
 
 
=== Project Video ===
 
Upload a video of your project and post the link here.
 
 
 
=== Project Source Code ===
 
Send me your zipped source code and I will upload this to SourceForge and link it for you.
 
 
 
== References ==
 
=== Acknowledgement ===
 
1. Opto-coupler wikipedia entry: [http://en.wikipedia.org/wiki/Opto-isolator]
 
2. Opto-coupler datasheet: [http://www.ti.com/lit/ds/symlink/4n35.pdf]
 
 
 
=== References Used ===
 
List any references used in project.
 
 
 
=== Appendix ===
 
You can list the references you used.
 

Latest revision as of 20:35, 11 November 2013

This is your user page; please do not write your report at this article.