S21: Roadster

From Embedded Systems Learning Academy
Revision as of 20:11, 28 May 2021 by Proj user9 (talk | contribs) (Mobile Application)

Jump to: navigation, search

Roadster

System Design

Abstract

Roadster is a battery powered autonomous car, that drives itself to a specified destination and avoids any obstacles that comes its way. The car infrastructure has four Nodes (Geo, Sensor, Driver and Motor) that communicate over the CAN bus and an android application interface to set the destination location. In order to make an informed decision the car processes Geo and Sensor Node’s data which is used to steer the car in the right direction.

Introduction

The project was divided into 5 modules:

  • Sensor Node- Detecting obstacles in the vicinity of the car to avoid hitting the obstacle and maneuver around the same.
  • Geo Node- Provide heading for car to reach destination. Communicate over blue tooth with mobile application. Battery state.
  • Driver Node- Manipulate turn angles and forward/reverse speed based on the inputs from Sensor and Geo nodes
  • Motor Node- PID control logic to attain the said speed/direction desired by driver node.
  • Android Application- Dashboard for real time data from car. Send instruction such as destination, way points and start/stop.

Team Members & Responsibilities

<Team Picture>

Tejas Pidwalkar

  • Sensor Node
  • Driver Node

Nimit Patel

  • Geo Node

Tirth Pandya

  • Motor Node
  • PCB design

Srikar Reddy

  • Android Application

Sourab Gupta

  • Driver Node


Gitlab Repository

<Provide ECU names and members responsible> <One member may participate in more than one ECU>

  • Sensor Node
    • Link to Gitlab user1
  • Geo Node
    • Link to Gitlab user1
  • Motor Node
    • Link to Gitlab user1
  • Android Application
    • Link to Gitlab user1


Schedule

Week# Start Date End Date Task Actual Completion Status
1

03/01 to 03/07 Start of Phase 1

  • 03/01
  • 03/04
  • 03/05
  • 03/04
  • 03/07
  • 03/07
  • Study and discuss previous project reports
  • Brainstorm on the requirements for the project
  • Identify and order/purchase the required components
  • 03/04
  • 03/07
  • 03/09
  • Completed
  • Completed
  • Completed
2

03/08 to 03/14

  • 03/08
  • 03/08
  • 03/11
  • 03/12
  • 03/08
  • 03/08
  • 03/14
  • 03/14
  • Create and setup Gitlab Repository
  • Create and setup Confluence for document collaboration
  • Study the datasheets and manual of acquired components
  • Distribute initial roles among the team members
  • 03/04
  • 03/07
  • 03/17
  • 03/15
  • Completed
  • Completed
  • Completed
  • Completed
3

03/15 to 03/21

  • 03/15
  • 03/15
  • 03/19
  • 03/18
  • 03/15
  • 03/18
  • 03/18
  • 03/21
  • 03/21
  • 03/27
  • Interface ultrasonic sensors and test the functionality
  • Interface GPS and Compass and test the functionality
  • Analyze and decide the hardware placement of the RC Car
  • Create SENSOR and DRIVER nodes to transmit and receive data
  • Identify the Android app requirements and start studying the Android framework
  • 03/18
  • 03/22
  • 03/20
  • 03/21
  • 03/25
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
4

03/22 to 03/28

  • 03/22
  • 03/22
  • 03/25
  • 03/27
  • 03/22
  • 03/25
  • 03/24
  • 03/28
  • 03/31
  • 03/28
  • Create the GEO node to get coordinates and cardinal directions from GPS and Compass
  • Interface the Bluetooth module to communicate with SJ-two board
  • Create the MOTOR node to drive the RC Car
  • Start designing the DBC file
  • Develop an initial version of the Android app
  • 03/24
  • 03/28
  • 03/30
  • 03/28
  • Completed
  • In Progress
  • Completed
  • Completed
  • Completed
5

03/29 to 04/04 End of Phase 1

  • 04/02
  • 03/29
  • 03/29
  • 03/29
  • 03/31
  • 04/03
  • 04/03
  • 04/01
  • 04/01
  • 04/01
  • 04/03
  • 04/04
  • Finalize the DBC file
  • Design obstacle avoidance and steering logic on the DRIVER node
  • Design motor driving logic on the MOTOR node with the encoder
  • Interface the LCD module with the DRIVER node to display messages
  • Integrate sensor data on the SENSOR node
  • Collective Test 1: Integrate all the completed modules and test on BusMaster
  • 04/05
  • 04/01
  • 04/04
  • 04/04
  • Completed
  • Completed
  • In Progress
  • In Progress
  • Completed
  • Completed
6

04/05 to 04/11 Start of Phase 2

  • 04/05
  • 04/05
  • 04/08
  • 04/10
  • 04/08
  • 04/08
  • 04/10
  • 04/11
  • Tune the SENSOR and DRIVER nodes to drive the RC car
  • Communicate to the DRIVER node over Bluetooth via Android app
  • Debug and revise the integrated modules with necessary improvements
  • Collective Test 2: Drive the car to a hardcoded GPS destination
  • N/A
  • N/A
  • N/A
  • N/A
7

04/12 to 04/18

  • 04/12
  • 04/15
  • 04/12
  • 04/17
  • 04/15
  • 04/18
  • 04/16
  • 04/18
  • Integrate GEO node to DRIVER node for navigation
  • Design driving decision logic based on the navigation data
  • Design a dashboard on the LCD to display the values
  • Collective Test 3: Test the car driving with navigation data from the Android app
  • N/A
  • N/A
  • N/A
  • N/A
8

04/19 to 04/25 End of Phase 2

  • 04/19
  • 04/19
  • 04/19
  • 04/19
  • 04/25
  • 04/25
  • 04/25
  • 04/25
  • Add functionalities to display various sensor data on the Android app
  • Design and 3D print the required components
  • Design and order PCB
  • Test and improve the RC car performance based on the changes
  • N/A
  • N/A
  • N/A
  • N/A
9

04/26 to 05/02 Start of Phase 3

  • 04/26
  • 04/26
  • 04/26
  • 05/01
  • 04/30
  • 04/30
  • 04/30
  • 05/02
  • Design individual architecture diagrams and algorithms for documentation
  • Make any necessary improvements based on previous test results
  • Complete the final version of the Android app
  • Collective Test 4: Test car on various terrains and slopes
  • N/A
  • N/A
  • N/A
  • N/A
10

05/03 to 05/09

  • 05/03
  • 05/03
  • 05/03
  • 05/08
  • 05/07
  • 05/07
  • 05/07
  • 05/09
  • Replace the circuits with their corresponding PCBs and assemble
  • Complete the RC Car structure and assembly with the 3D printed parts - Prototype 1
  • Refactor the code modules with necessary improvements
  • Collective Test 5: Test the Prototype 1 with the aim of sending the car to return Preet's PCAN Dongle
  • N/A
  • N/A
  • N/A
  • N/A
11

05/10 to 05/16 End of Phase 3

  • 05/10
  • 05/10
  • 05/10
  • 05/15
  • 05/16
  • 05/16
  • 05/16
  • 05/16
  • Revise and improve the wiki report to cover all the aspects of design and implementation
  • Fix all the errors and make improvements
  • Final testing of all the modules and car
  • Collective Test 6: Have the final version of the project tested with all the functionalities
  • N/A
  • N/A
  • N/A
  • N/A


Parts List & Cost

Item# Part Desciption Vendor Qty Cost
1 RC Car Traxxas [1] 1 $250.00
2 CAN Transceivers MCP2551-I/P Comimark [2] 5 $7.00
3 Ultrasonic Sensors Max Botix[3] 5 $150.00
4 GPS and Antenna Adafruit[4] 1 $60.00
5 HC05 bluetooth RF Transreceiver HiLetgo[5] 1 $12.59
6 Triple-axis Accelerometer Adafruit[6] 1 $21.40
7 Traxxas RPM Sensor Traxxas[7] 1 $12
8 Discrete Electronic Components Generic[8] 1 $28.75
9 Buck-Boost Voltage Regulator Generic[9] 1 $11.99
10 Traxxas Telemetry Trigger magnet & holder Traxxas[10] 1 $6.35
11 Amazon[] 1 $
12 Amazon[] 1 $
13 Amazon[] 1 $
14 Amazon[] 1 $


Printed Circuit Board

Roadster Schematic

<

Roadster PCB

CAN Communication

<Talk about your message IDs or communication strategy, such as periodic transmission, MIA management etc.>

Hardware Design

<Show your CAN bus hardware design>

DBC File

<Gitlab link to your DBC file> <You can optionally use an inline image>




Sensor ECU

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

Neighboring Sensor Interference:

  • As explained above, we have mounted three ultrasonic sensors in the front, and those were configured to range in continuous mode, in which sensors were continuously measuring distance by transmitting beam. Out of 3, the middle sensor is of type with wider beam to detect blind spots ahead.
  • Most of the time, we observed that the obstacle in the middle sensor range used also gets detected by the left/right sensor, which disturbs driving logic. This used to happen due to sensor beam interference among three sensors.
  • To solve this problem, we decided to trigger sensor beams in such time intervals that they won’t interfere with neighboring ones. We used the Rx pin of the sensor to trigger ranging and scheduled to trigger left and right sensor at one time and middle sensor next time. This sequence helped us avoid interference altogether.

Frequent noisy measurements:

  • While reading the obstacle distance, it used to change suddenly to some random value, and that used to disturb driving logic. To get noise-free readings from sensors, we implemented a median filter. All the read values from sensors have been collected in the respective buffer of 10 elements. While sending obstacle distance on CAN bus, the median filter sort the buffer and takes an average of 5 median values. This way, it helped us to remove almost all noisy values.

< List of problems and their detailed resolutions>



Motor ECU

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Geographical Controller

Repository link for Geo Controller

Hardware Design

GPS Module
3 Axis Magnetometer (eCompass)
Battery Monitoring
Bluetooth Trans-receiver



The SJ2 board communicates with:

  • Bluettoth transreceiver over UART
  • LSM303DLHC over I2C
  • GPS model over UART
  • Battery monitoring

Considering the orientation of the car changes as it travel along the land, tilt compensation logic for heading calculation using the magnetometer is a must for accurate measurement. Without the tilt compensation algorithm which uses the onboard accelorometer, the heading computation can have error up to 60 degrees, which has the potential to send the car off course.

For battery monitoring, the values for the voltage divider should be chosen such that the full range of the onboard ADC can be efficiently used. Depending one the cell type of the battery, the discharge curve can be use to map the charge state corresponding to voltage level. This method has its flaws and sophisticated techniques involving Coulomb count yields far better results, however, the technique discussed above suffices the needs of our project. Charge state of battery transmitted over Mobile app, greatly facilitates the charging schedule while testing and final demo day.



Software Design

The GEO controller is divided into 5 parts.

  • The current location of the car is determined using the GPS.
  • The current magnetic heading of car is determined using the on board compass.
  • The way point calculation determines the nearest way point continuously by computing the distance using Haversine formula and current location using GPS.
  • The heading is also computed using the Haversine formula and the difference between the actual and required is sent over the CAN bus for heading correction.
  • Alternatively, once the car is within the threshold distance, next way point is selected and the car heads to the next way point.


Heading computation from geographical (Geo) controller

Technical Challenges

  • The GPS module sends data at 9600 baud rate, updating the data every one second. The data update rate needs to be updated to 10Hz for fast maneuvering and course correction of the car. If the update frequency is updated, the data sent over the UART is higher than it can handle in 10Hz periodic function. Hence, only GPGGA messages should be enabled to extract the required data and reduce the time spent in parsing the incoming string. NEMA (PMTK) messages should be correctly configured on the module for desired functioning.
  • Heading calculation without the tilt compensation logic using the onboard accelorometer of LSM303 is in accurate. Reading accelorometer values requires and offset of 0x80 to the byte addressing of the accelorometer read. Magnetometer need no such offset. This is weird, considering both the I2C devices reside on the same physical chip.
  • Using data type as float as opposed to double, utilizes the onboard FPU, which is faster. Double utilizes software implementation, which takes more clock cycle. Considering extensive use of math library in distance/heading measurement and tilt compensation algorithm, completing the task with the periodic is of at most importance.
  • GPS fix is best when when there are no obstruction above the module. Module requires clear wide view of sky for a fast fix and error free location detection.
  • LSM303DLHC is sensitive to even weak magnetic field interference. Place the chip devoid of such active/passive magnetic fields.
  • Calibrating LSM303 is a must to get accurate heading values. 2-point calibration worked just fine for our team. More sophisticated methods are available too.

Communication Bridge Controller & LCD

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Driver Node

https://gitlab.com/nimit.patel/roadster/-/tree/Main/Driver_Node

Hardware Design

The Driver Node has one peripheral connected to it and that is the LCD screen.

Software Design

The driver node controls the logic of steering the car in the right direction based on the data received from the Sensor and Geo Nodes. The following flowchart describes that process.

  • Driver Node Flow Chart

FlowChartDriverNode.png

In case there are obstacles in the path where the car wants to move to, the following obstacle avoid logic would kick in.

  • Driver Node Obstacle Avoidance Logic

ObstacleAvoidanceDriverNode.png The work in the Driver Node is done using two different periodic tasks. Here is a description of those periodic tasks and what they do.

  • 1 Hz Loop:
    • Transmit debug messages over the CAN bus
    • Transmit messages on the LCD
    • Transmit destination reached flag over the CAN Bus
  • 20 Hz Loop:
    • Receive Sensor Data
    • Receive Geo Data
    • Process and Transmit Data(Motor Direction and Speed) to Motor Node
  • LCD Interface

The LCD interface on the Driver is used to print some important information about the car. This is what it prints.

    • Car Speed
    • Distance from the Destination
    • Car State (Car Stopped from the App, Car Moving, Destination Reached)

Technical Challenges

The Driver Node did not have much hardware interfaced on it apart from LCD. So from the hardware side there were no technical challenges. On the software front as well there were not many challenges as unit tests helped debug most of the issues then and there.



Mobile Application

We created a lightweight mobile app to navigate our car, It can communicate with the car via Bluetooth and is capable of sending Destination co-ordinates along with checkpoints. Receive and Update live location on Google Maps, send Start, Stop and Clear commands, Receive and Display Debug Data.

  • Data from roadster
  • Checkpoints

User Interface

The app has minimal buttons on the same screen as Google Maps View to confirm the cars current state and location before sending the commands.

       connect_Btn.setOnClickListener(new View.OnClickListener() {
           @Override
           public void onClick(View v) {
               listPairedDevices(v);
           }
       });
       clear.setOnClickListener(new View.OnClickListener() {
           @Override
           public void onClick(View v) {
               try {
                   if(!state) {
                       mConnectedThread.write("--,\n");
                       mMap.clear();
                       checkpoints.clear();
                       sending_status.setText("Waiting");
                   }
                   else{
                       Toast.makeText(getApplicationContext(),"Stop the car First",Toast.LENGTH_SHORT).show();
                   }
               }
               catch (Exception e)
               {
                   Toast.makeText(getApplicationContext(),"Connect to Roadster First",Toast.LENGTH_SHORT).show();
               }
           }
       });
       stop.setOnClickListener(new View.OnClickListener() {
           @Override
           public void onClick(View v) {
               try {
                   mConnectedThread.write("!!,\n");
                   state=false;
                   move_camera=false;
                   car_status.setText("   stopped");
               }
               catch (Exception e)
               {
                   Toast.makeText(getApplicationContext(),"Connect to Roadster First",Toast.LENGTH_SHORT).show();
               }
           }
       });
       start.setOnClickListener(new View.OnClickListener() {
           @Override
           public void onClick(View v) {
               try {
                   mConnectedThread.write("##,\n");
                   state=true;
                   move_camera=true;
                   car_status.setText("   started");
               }
               catch (Exception e)
               {
                   Toast.makeText(getApplicationContext(),"Connect to Roadster First",Toast.LENGTH_SHORT).show();
               }
           }
       });
       send_cpts.setOnClickListener(new View.OnClickListener() {
           @Override
           public void onClick(View v) {
               try {
                   sending_status.setText("....");
               for(int i=0;i<checkpoints.size();i++) {
                   String cpt="GPS,"+checkpoints.get(i).latitude+","+checkpoints.get(i).longitude+"\n";
                   mConnectedThread.write(cpt);
               }
               sending_status.setText("Sent");
               }
               catch (Exception e)
               {
                   Toast.makeText(getApplicationContext(),"Connect to Roadster First",Toast.LENGTH_SHORT).show();
               }
           }
       });

Software Design

This app has mainly two activities, The main activity and maps activity.

Maps Activity

This is the only functional activity for the app and is responsible for the Google Maps and Bluetooth related Tasks. User can also dynamically select multiple checkpoints and send them to the bridge node. This is achieved using java vector and OnMapclickListener setup to read each marker placed by the user.

mMap.setOnMapClickListener(new GoogleMap.OnMapClickListener() {

           @Override
           public void onMapClick(LatLng latLng) {
               int precision = (int) Math.pow(10,6);
               double new_latitude = (double)((int)(precision*latLng.latitude))/precision;
               double new_longitude = (double)((int)(precision*latLng.longitude))/precision;
               LatLng myloc = new LatLng(latLng.latitude, latLng.longitude);
               mMap.addMarker(new MarkerOptions().position(myloc).title("Destination"));
               mMap.moveCamera(CameraUpdateFactory.newLatLngZoom(myloc,20));
               checkpoints.add(new LatLng(new_latitude,new_longitude));
               destination_coordinates = "GPS," + new_latitude + "," + new_longitude +"\n";
           }
       });

Bluetooth

The Bluetooth connection is initially set up by reading the id and MAC addresses of the selected device, The available devices are displayed on a listView under the connect button. Once the socket is established, Bluetooth module provides read() and write() API used to communicate.


           if(!mBTAdapter.isEnabled()) {
               Toast.makeText(getBaseContext(), "Bluetooth not on", Toast.LENGTH_SHORT).show();
               return;
           }
           mBluetoothStatus.setText("Connecting...");
           // Get the device MAC address, which is the last 17 chars in the View
           String info = ((TextView) v).getText().toString();
           final String address = info.substring(info.length() - 17);
           final String name = info.substring(0,info.length() - 17);
           new Thread()
           {
               public void run() {
                   boolean fail = false;
                   BluetoothDevice device = mBTAdapter.getRemoteDevice(address);
                   try {
                       mBTSocket = createBluetoothSocket(device);
                   } catch (IOException e) {
                       fail = true;
                       Toast.makeText(getBaseContext(), "Socket creation failed", Toast.LENGTH_SHORT).show();
                   }
                   // Establish the Bluetooth socket connection.
                   try {
                       mBTSocket.connect();
                   } catch (IOException e) {
                       try {
                           fail = true;
                           mBTSocket.close();
                           mHandler.obtainMessage(CONNECTING_STATUS, -1, -1)
                                   .sendToTarget();
                       } catch (IOException e2) {
                           Toast.makeText(getBaseContext(), "Socket creation failed", Toast.LENGTH_SHORT).show();
                       }
                   }
                   if(fail == false) {
                       mConnectedThread = new ConnectedThread(mBTSocket);
                       mConnectedThread.start();
                       mHandler.obtainMessage(CONNECTING_STATUS, 1, -1, name)
                               .sendToTarget();
                   }


The Bridge node sends data in string format with end of line chars, The Bluetooth handler concatenates the received data and waits for the "end of line" before trying to parse it. Below is the code snippet that parses the incoming stream with location and debug data sent by the bridge node.

                   if(readMessage.indexOf("\n")>0) {
                       message = new StringTokenizer(readMessage, "\n");
                       StringTokenizer st;
                       while (message.hasMoreTokens()) {
                           st = null;
                           received_line = message.nextToken();
                           st = new StringTokenizer(received_line, ",");
                           try {
                               read = st.nextToken();
                           } catch (Exception e) {
                               continue;
                           }
                           if (read.compareTo("GPS") == 0) {
                               try {
                                   LatLng current_location = new LatLng(Double.parseDouble(st.nextToken()), Double.parseDouble(st.nextToken()));
                                   waypoint.setText(st.nextToken("\n").replace(",", ""));
                                   prev.remove();
                                   prev = mMap.addMarker(new 
                                          MarkerOptions().position(current_location).anchor(0.5f,0.5f).rotation(compass_value).title("Roadster")
                                          .icon(BitmapFromVector(getApplicationContext(), R.drawable.ic_baseline_directions_car_filled_24)));
                            if (state || init) {
                                       mMap.moveCamera(CameraUpdateFactory.newLatLng(current_location));
                                       if (current_location.latitude != 0) init = false;
                                   }
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("speed") == 0) {
                               try {
                                   speed.setText(st.nextToken("\n").replace(",", "") + "m/s");
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("sens") == 0) {
                               try {
                                   left.setText(st.nextToken() + "cm");
                                   right.setText(st.nextToken() + "cm");
                                   center.setText(st.nextToken() + "cm");
                                   back.setText(st.nextToken("\n").replace(",", "") + "cm");
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("comp") == 0) {
                               try {
                                   compass.setText(st.nextToken());
                                   String compass_s=st.nextToken("\n").replace(",", "");
                                   compass_raw.setText(compass_s);
                                   compass_value =Integer.parseInt(compass_s);
                                   prev.setAnchor(0.5f,0.5f);
                                   prev.setRotation(compass_value);
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("dist") == 0) {
                               try {
                                   String dis=st.nextToken("\n").replace(",", "");
                                   distance.setText(dis+"m");
                                   //int prog=(int)Float.parseFloat(dis)%200;
                                   //progress.setProgress(prog);
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("mot") == 0) {
                               try {
                                   rps.setText(st.nextToken());
                                   pwm.setText(st.nextToken("\n").replace(",", ""));
                               } catch (Exception e) {
                               }
                           }
                           else if(read.compareTo("bat")==0){
                               try{
                                   battery.setText(st.nextToken("\n").replace(",", "")+"%");
                               }catch (Exception e){
                               }
                           }
                      }
                       readMessage="";

Technical Challenges

Given no experience in Android Development, we had to start from the basics about the activities, message passing etc. The initial challenge was to understand the google maps API and generate the API key to access google cloud to implement the map view and markers. Implementing Bluetooth communication required scanning the list of paired devices and acquire the MAC address required to open a socket using the provided API. Fortunately, there are many example implementations to go through. We decided to use a similar line buffer that is used in the Geo node to read the debug data sent from the app, this helped solve the challenge of parsing the group of variables sent by the bridge node by reading from the CAN bus.






Conclusion

<Organized summary of the project>

<What did you learn?>

  • Embedded project are generally single board projects. The mandatory use of CAN bus required a great deal of collaboration, where all board are interdependent and the system design should be robust to make it work every single time, the car is used for its intended purpose.
  • Unit testing helps in early phase of the project, where the hardware setup is not ready yet, but one needs to start coding to get ahead of the curve and start building logic. This helps in troubleshooting the hardware as well.

Project Video

Project Source Code

Repository link for Autonomous RC Car

Advise for Future Students

  • Get the hardware modules and test the same with SJ2 (Before the Mid Semester exams). Once this is done, create a PCB and mount devices and then start the extensive software testing. Considering the car is moving object, temporary connections over bread board and zero PCB might work, but reliability will remain a doubt at the back of the head. Eliminate the same by creating the PCB early. You might even want to iterate to a second PCB, once you are a few weeks into testing and want to change amend previous mistakes/improve existing layout and placements. The time and effort this will save is worth it.
  • Once the hardware is nearing its completion, the Mobile app should be ready in its rudimentary form. Having a hand held debug device is more useful, compared to using PCAN dongle which is great for static testing.
  • The software will take multiple iteration by testing your car in various field scenarios. This is not a project which can be completed a night before demo. Keep a healthy amount of time for testing.
  • The sole working power socket available in university outside of the university buildings is available on the top floor of the tenth street car garage. This is especially useful when testing in field.

Acknowledgement

  • Building a hardware project without the availability of a electronics lab of the university which had been shut, due to COVID-19 pandemic tested our resourcefulness to our extremes.Considering the remote nature of course work, resource availability in any shape or form from university was sadly non existent. All the team members should be appreciated for their unwavering enthusiasm to make this a success story.
  • Preet's advice for buying quality hardware parts should be followed to the line.

=== References ===