S21: Roadster

From Embedded Systems Learning Academy
Revision as of 20:07, 27 May 2021 by Proj user3 (talk | contribs) (Technical Challenges)

Jump to: navigation, search

Roadster

System Design

Abstract

Roadster is a battery powered autonomous car, that drives itself to a specified destination and avoids any obstacles that comes its way. The car infrastructure has four Nodes (Geo, Sensor, Driver and Motor) that communicate over the CAN bus and an android application interface to set the destination location. In order to make an informed decision the car processes Geo and Sensor Node’s data which is used to steer the car in the right direction.

Introduction

The project was divided into N modules:

  • Sensor Node
  • Geo Node
  • Driver Node
  • Geo Node
  • Android Application

Team Members & Responsibilities

<Team Picture>

Tejas Pidwalkar

  • Sensor Node
  • Driver Node

Nimit Patel

  • Geo Node

Tirth Pandya

  • Motor Node
  • PCB design

Srikar Reddy

  • Android Application

Sourab Gupta

  • Driver Node


Gitlab Repository

<Provide ECU names and members responsible> <One member may participate in more than one ECU>

  • Sensor Node
    • Link to Gitlab user1
    • Link to Gitlab user2
  • Geo Node
    • Link to Gitlab user1
    • Link to Gitlab user2
  • Motor Node
    • Link to Gitlab user1
    • Link to Gitlab user2
  • Android Application
    • Link to Gitlab user1
    • Link to Gitlab user2
  • Testing Team
    • Link to Gitlab user1
    • Link to Gitlab user2


Schedule

Week# Start Date End Date Task Actual Completion Status
1

03/01 to 03/07 Start of Phase 1

  • 03/01
  • 03/04
  • 03/05
  • 03/04
  • 03/07
  • 03/07
  • Study and discuss previous project reports
  • Brainstorm on the requirements for the project
  • Identify and order/purchase the required components
  • 03/04
  • 03/07
  • 03/09
  • Completed
  • Completed
  • Completed
2

03/08 to 03/14

  • 03/08
  • 03/08
  • 03/11
  • 03/12
  • 03/08
  • 03/08
  • 03/14
  • 03/14
  • Create and setup Gitlab Repository
  • Create and setup Confluence for document collaboration
  • Study the datasheets and manual of acquired components
  • Distribute initial roles among the team members
  • 03/04
  • 03/07
  • 03/17
  • 03/15
  • Completed
  • Completed
  • Completed
  • Completed
3

03/15 to 03/21

  • 03/15
  • 03/15
  • 03/19
  • 03/18
  • 03/15
  • 03/18
  • 03/18
  • 03/21
  • 03/21
  • 03/27
  • Interface ultrasonic sensors and test the functionality
  • Interface GPS and Compass and test the functionality
  • Analyze and decide the hardware placement of the RC Car
  • Create SENSOR and DRIVER nodes to transmit and receive data
  • Identify the Android app requirements and start studying the Android framework
  • 03/18
  • 03/22
  • 03/20
  • 03/21
  • 03/25
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
4

03/22 to 03/28

  • 03/22
  • 03/22
  • 03/25
  • 03/27
  • 03/22
  • 03/25
  • 03/24
  • 03/28
  • 03/31
  • 03/28
  • Create the GEO node to get coordinates and cardinal directions from GPS and Compass
  • Interface the Bluetooth module to communicate with SJ-two board
  • Create the MOTOR node to drive the RC Car
  • Start designing the DBC file
  • Develop an initial version of the Android app
  • 03/24
  • 03/28
  • 03/30
  • 03/28
  • Completed
  • In Progress
  • Completed
  • Completed
  • Completed
5

03/29 to 04/04 End of Phase 1

  • 04/02
  • 03/29
  • 03/29
  • 03/29
  • 03/31
  • 04/03
  • 04/03
  • 04/01
  • 04/01
  • 04/01
  • 04/03
  • 04/04
  • Finalize the DBC file
  • Design obstacle avoidance and steering logic on the DRIVER node
  • Design motor driving logic on the MOTOR node with the encoder
  • Interface the LCD module with the DRIVER node to display messages
  • Integrate sensor data on the SENSOR node
  • Collective Test 1: Integrate all the completed modules and test on BusMaster
  • 04/05
  • 04/01
  • 04/04
  • 04/04
  • Completed
  • Completed
  • In Progress
  • In Progress
  • Completed
  • Completed
6

04/05 to 04/11 Start of Phase 2

  • 04/05
  • 04/05
  • 04/08
  • 04/10
  • 04/08
  • 04/08
  • 04/10
  • 04/11
  • Tune the SENSOR and DRIVER nodes to drive the RC car
  • Communicate to the DRIVER node over Bluetooth via Android app
  • Debug and revise the integrated modules with necessary improvements
  • Collective Test 2: Drive the car to a hardcoded GPS destination
  • N/A
  • N/A
  • N/A
  • N/A
7

04/12 to 04/18

  • 04/12
  • 04/15
  • 04/12
  • 04/17
  • 04/15
  • 04/18
  • 04/16
  • 04/18
  • Integrate GEO node to DRIVER node for navigation
  • Design driving decision logic based on the navigation data
  • Design a dashboard on the LCD to display the values
  • Collective Test 3: Test the car driving with navigation data from the Android app
  • N/A
  • N/A
  • N/A
  • N/A
8

04/19 to 04/25 End of Phase 2

  • 04/19
  • 04/19
  • 04/19
  • 04/19
  • 04/25
  • 04/25
  • 04/25
  • 04/25
  • Add functionalities to display various sensor data on the Android app
  • Design and 3D print the required components
  • Design and order PCB
  • Test and improve the RC car performance based on the changes
  • N/A
  • N/A
  • N/A
  • N/A
9

04/26 to 05/02 Start of Phase 3

  • 04/26
  • 04/26
  • 04/26
  • 05/01
  • 04/30
  • 04/30
  • 04/30
  • 05/02
  • Design individual architecture diagrams and algorithms for documentation
  • Make any necessary improvements based on previous test results
  • Complete the final version of the Android app
  • Collective Test 4: Test car on various terrains and slopes
  • N/A
  • N/A
  • N/A
  • N/A
10

05/03 to 05/09

  • 05/03
  • 05/03
  • 05/03
  • 05/08
  • 05/07
  • 05/07
  • 05/07
  • 05/09
  • Replace the circuits with their corresponding PCBs and assemble
  • Complete the RC Car structure and assembly with the 3D printed parts - Prototype 1
  • Refactor the code modules with necessary improvements
  • Collective Test 5: Test the Prototype 1 with the aim of sending the car to return Preet's PCAN Dongle
  • N/A
  • N/A
  • N/A
  • N/A
11

05/10 to 05/16 End of Phase 3

  • 05/10
  • 05/10
  • 05/10
  • 05/15
  • 05/16
  • 05/16
  • 05/16
  • 05/16
  • Revise and improve the wiki report to cover all the aspects of design and implementation
  • Fix all the errors and make improvements
  • Final testing of all the modules and car
  • Collective Test 6: Have the final version of the project tested with all the functionalities
  • N/A
  • N/A
  • N/A
  • N/A


Parts List & Cost

Item# Part Desciption Vendor Qty Cost
1 RC Car Traxxas [1] 1 $250.00
2 CAN Transceivers MCP2551-I/P Comimark [2] 5 $7.00
3 Ultrasonic Sensors Max Botix[3] 5 $150.00
4 GPS and Antenna Adafruit[4] 1 $60.00
5 HC05 bluetooth RF Transreceiver HiLetgo[5] 1 $12.59
6 Triple-axis Accelerometer Adafruit[6] 1 $21.40
7 Traxxas RPM Sensor Traxxas[7] 1 $12
8 Discrete Electronic Components Generic[8] 1 $28.75
9 Buck-Boost Voltage Regulator Generic[9] 1 $11.99
10 Traxxas Telemetry Trigger magnet & holder Traxxas[10] 1 $6.35
11 Amazon[] 1 $
12 Amazon[] 1 $
13 Amazon[] 1 $
14 Amazon[] 1 $


Printed Circuit Board

<Picture and information, including links to your PCB>



CAN Communication

<Talk about your message IDs or communication strategy, such as periodic transmission, MIA management etc.>

Hardware Design

<Show your CAN bus hardware design>

DBC File

<Gitlab link to your DBC file> <You can optionally use an inline image>




Sensor ECU

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

Neighboring Sensor Interference:

As explained above, we have mounted three ultrasonic sensors in the front, and those were configured to range in continuous mode, in which sensors were continuously measuring distance by transmitting beam. Out of 3, the middle sensor is of type with wider beam to detect blind spots ahead.

Most of the time, we observed that the obstacle in the middle sensor range used also gets detected by the left/right sensor, which disturbs driving logic. This used to happen due to sensor beam interference among three sensors.

To solve this problem, we decided to trigger sensor beams in such time intervals that they won’t interfere with neighboring ones. We used the Rx pin of the sensor to trigger ranging and scheduled to trigger left and right sensor at one time and middle sensor next time. This sequence helped us avoid interference altogether.

< List of problems and their detailed resolutions>



Motor ECU

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Geographical Controller

Repository link for Geo Controller

Hardware Design

GPS Module
3 Axis Magnetometer (eCompass)
Battery Monitoring
Bluetooth Trans-receiver



The SJ2 board communicates with:

  • Bluettoth transreceiver over UART
  • LSM303DLHC over I2C
  • GPS model over UART
  • Battery monitoring

Considering the orientation of the car changes as it travel along the land, tilt compensation logic for heading calculation using the magnetometer is a must for accurate measurement. Without the tilt compensation algorithm which uses the onboard accelorometer, the heading computation can have error up to 60 degrees, which has the potential to send the car off course.

For battery monitoring, the values for the voltage divider should be chosen such that the full range of the onboard ADC can be efficiently used. Depending one the cell type of the battery, the discharge curve can be use to map the charge state corresponding to voltage level. This method has its flaws and sophisticated techniques involving Coulomb count yields far better results, however, the technique discussed above suffices the needs of our project. Charge state of battery transmitted over Mobile app, greatly facilitates the charging schedule while testing and final demo day.



Software Design

Heading computation from geographical (Geo) controller

The GEO controller is divided into 5 parts.

  • The current location of the car is determined using the GPS.
  • The current magnetic heading of car is determined using the on board compass.
  • The way point calculation determines the nearest way point continuously by computing the distance using Haversine formula and current location using GPS.
  • The heading is also computed using the Haversine formula and the difference between the actual and required is sent over the CAN bus for heading correction.
  • Alternatively, once the car is within the threshold distance, next way point is selected and the car heads to the next way point.

Technical Challenges

  • The GPS module sends data at 9600 baud rate, updating the data every one second. The data update rate needs to be updated to 10Hz for fast maneuvering and course correction of the car. If the update frequency is updated, the data sent over the UART is higher than it can handle in 10Hz periodic function. Hence, only GPGGA messages should be enabled to extract the required data and reduce the time spent in parsing the incoming string. NEMA (PMTK) messages should be correctly configured on the module for desired functioning.
  • Heading calculation without the tilt compensation logic using the onboard accelorometer of LSM303 is in accurate. Reading accelorometer values requires and offset of 0x80 to the byte addressing of the accelorometer read. Magnetometer need no such offset. This is weird, considering both the I2C devices reside on the same physical chip.
  • Using data type as float as opposed to double, utilizes the onboard FPU, which is faster. Double utilizes software implementation, which takes more clock cycle. Considering extensive use of math library in distance/heading measurement and tilt compensation algorithm, completing the task with the periodic is of at most importance.
  • GPS fix is best when when there are no obstruction above the module. Module requires clear wide view of sky for a fast fix and error free location detection.

Communication Bridge Controller & LCD

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Driver Node

<Picture and link to Gitlab>


Hardware Design

Software Design

  • Flow Chart
Driver Node Flow Chart


  • Obstacle Avoidance Logic

Obstacle avoidance fsm2.png

  • 1 Hz Loop:
    • Transmit debug messages over the CAN bus
  • 20 Hz Loop:
    • Receive Sensor Data
    • Receive Geo Data
    • Process and Transmit Data(Motor Direction and Speed) to Motor Node

Technical Challenges

< List of problems and their detailed resolutions>



Mobile Application

<Picture and link to Gitlab> We created a lightweight mobile app to control our car, It can communicate with the car via Bluetooth and is capable of sending Destination co-ordinates along with checkpoints. Receive and Update live location on Google Maps, send Start, Stop and Clear commands, Receive and Display Debug Data.

Software Design

This app has mainly two activities, The main activity and maps activity.

Maps Activity

This is the only functional activity for the app and is responsible for the Google Maps and Bluetooth related Tasks. User can also dynamically select multiple checkpoints and send them to the bridge node. This is achieved using java vector and OnMapclickListener setup to read each marker placed by the user.

The Bluetooth connection is initially set up by reading the id and MAC addresses of the selected device, The available devices are displayed on a listView under the connect button. Bluetooth socket module provides read() and write() API used to communicate. Below is the code snippet that parses the incoming stream with location and debug data sent by the bridge node.

                   if(readMessage.indexOf("\n")>0) {
                       message = new StringTokenizer(readMessage, "\n");
                       StringTokenizer st;
                       while (message.hasMoreTokens()) {
                           st = null;
                           received_line = message.nextToken();
                           st = new StringTokenizer(received_line, ",");
                           try {
                               read = st.nextToken();
                           } catch (Exception e) {
                               continue;
                           }
                           if (read.compareTo("GPS") == 0) {
                               try {
                                   LatLng current_location = new LatLng(Double.parseDouble(st.nextToken()), Double.parseDouble(st.nextToken()));
                                   waypoint.setText(st.nextToken("\n").replace(",", ""));
                                   prev.remove();
                                   prev = mMap.addMarker(new 
                                          MarkerOptions().position(current_location).anchor(0.5f,0.5f).rotation(compass_value).title("Roadster")
                                          .icon(BitmapFromVector(getApplicationContext(), R.drawable.ic_baseline_directions_car_filled_24)));
                            if (state || init) {
                                       mMap.moveCamera(CameraUpdateFactory.newLatLng(current_location));
                                       if (current_location.latitude != 0) init = false;
                                   }
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("speed") == 0) {
                               try {
                                   speed.setText(st.nextToken("\n").replace(",", "") + "m/s");
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("sens") == 0) {
                               try {
                                   left.setText(st.nextToken() + "cm");
                                   right.setText(st.nextToken() + "cm");
                                   center.setText(st.nextToken() + "cm");
                                   back.setText(st.nextToken("\n").replace(",", "") + "cm");
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("comp") == 0) {
                               try {
                                   compass.setText(st.nextToken());
                                   String compass_s=st.nextToken("\n").replace(",", "");
                                   compass_raw.setText(compass_s);
                                   compass_value =Integer.parseInt(compass_s);
                                   prev.setAnchor(0.5f,0.5f);
                                   prev.setRotation(compass_value);
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("dist") == 0) {
                               try {
                                   String dis=st.nextToken("\n").replace(",", "");
                                   distance.setText(dis+"m");
                                   //int prog=(int)Float.parseFloat(dis)%200;
                                   //progress.setProgress(prog);
                               } catch (Exception e) {
                               }
                           } else if (read.compareTo("mot") == 0) {
                               try {
                                   rps.setText(st.nextToken());
                                   pwm.setText(st.nextToken("\n").replace(",", ""));
                               } catch (Exception e) {
                               }
                           }
                           else if(read.compareTo("bat")==0){
                               try{
                                   battery.setText(st.nextToken("\n").replace(",", "")+"%");
                               }catch (Exception e){
                               }
                           }
                      }
                       readMessage="";

Hardware Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>






Conclusion

<Organized summary of the project>

<What did you learn?>

Project Video

Project Source Code

Repository link for Autonomous RC Car

Advise for Future Students

  • Get the hardware modules and test the same with SJ2 (Before the Mid Semester exams). Once this is done, create a PCB and mount devices and then start the extensive software testing. Considering the car is moving object, temporary connections over bread board and zero PCB might work, but reliability will remain a doubt at the back of the head. Eliminate the same by creating the PCB early. You might even want to iterate to a second PCB, once you are a few weeks into testing and want to change amend previous mistakes/improve existing layout and placements. The time and effort this will save is worth it.
  • Once the hardware is nearing its completion, the Mobile app should be ready in its rudimentary form. Having a hand held debug device is more useful, compared to using PCAN dongle which is great for static testing.
  • The software will take multiple iteration by testing your car in various field scenarios. This is not a project which can be completed a night before demo. Keep a healthy amount of time for testing.

Acknowledgement

=== References ===