Difference between revisions of "S20: Bucephalus"

From Embedded Systems Learning Academy
Jump to: navigation, search
(Technical Challenges)
(Hardware Design)
Line 626: Line 626:
  
 
  <Motor_Module_Schematic.png>
 
  <Motor_Module_Schematic.png>
 +
 +
[[File:Final.jpg|thumb|1000px|caption|right|Bucephalus Logo]]
  
  

Revision as of 05:23, 16 May 2020

Bucephalus Logo

ABSTRACT

Bucephalus is a Self Driving RC car using CAN communication based on FreeRTOS(Hard RTOS). The RC car takes real time inputs and covert it into the data that can be processed to monitor and control to meet the desired requirements. In this project, we aim to design and develop a self-driving car that autonomously navigates from the current location to the destination (using Waypoint Algorithm )which is selected through an Android application and at the same time avoiding all the obstacles in the path using Obstacle avoidance algorithm . It also Increases or Decreases speed on Uphill and downhill (using PID Algorithm)as well as applies breaks at required places. The car comprises of 4 control units communicating with each other over the CAN Bus using CAN communication protocol, each having a specific functionality that helps the car to navigate to its destination successfully.

INTRODUCTION

Objectives of the RC Car:-

1) Driver Controller:- Detection and avoidance of the obstacles coming in the path of the RC car by following Obstacle detection avoidance.
2) Geographical Controller:- Getting the GPS coordinates from the Android Application and traveling to that point using Waypoint Algorithm
3) System hardware communication using PCB Design.
4) Bridge and Sensor Controller:- Communication between the Driver Board and Android Mobile Application using wireless bluetooth commmunication.
5) Motor Controller:- Control the Servo Motor for Direction and DC motor for speed. Implementation of PID Algorithm on normal road uphill and down hill to maintain speed

The project is divided into six main modules:

CORE MODULES OF RC CAR

  • Android Mobile Application
  • Bridge and Sensor Controller
  • Geographical Controller
  • Driver and LCD Controller
  • Motor Controller
  • Hardware Integration and PCB Designing

Team Members & Responsibilities

<Team Picture>

Bucephalous GitLab - [1]

  • Mohit Ingale GitLab LinkedIn
    • Driver and LCD Controller
    • Hardware Integration and PCB Designing
    • Testing Team / Code Reviewers
  • Shreya Patankar GitLab LinkedIn
    • Geographical Controller
    • Hardware Integration and PCB Designing
    • Testing Team / Code Reviewers
    • Wiki Page
  • Nicholas Kaiser GitLab LinkedIn
    • Bridge and Sensor Controller
    • Wiki Page
    • Hardware Integration and PCB Designing
  • Hari Haran Kura GitLab LinkedIn
    • Motor Controller
    • Testing Team / Code Reviewers
    • Hardware Integration and PCB Designing
  • Basangouda Patil GitLab LinkedIn
    • Android Mobile Application
    • Testing Team / Code Reviewers
  • Abhinandan Burli GitLab LinkedIn
    • Driver and LCD Controller
    • Testing Team / Code Reviewers
    • Hardware Integration and PCB Designing


Schedule

Week# Start Date End Date Task Status
1 02/16/2020 02/22/2020
  • Setup a team Google Docs folder
  • Brainstorm RC car design options
  • Research past semester RC car projects for ideas and parts needed
  • Put together a rough draft parts list
  • Setup a team GitLab repository
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
2 02/23/2020 02/29/2020
  • Decide on and order chassis
  • Discuss possible GPS modules
  • Discuss schedule for meeting dates and work days (Tuesdays are for code review and syncing, Saturdays are work days)
  • Discuss bluetooth communication approach (1 phone on car, 1 phone in controller's hands)
  • Discuss vehicle's driving checkpoints (checkpoints calculated after point B is specified)
  • Discuss wiring on RC car (1 battery to power motors and 1 power bank for everything else)
  • Discuss GitLab workflow (mirror our repo with Preet's, 3 approvals to merge to "working master" branch, resolve conflicts on "working master" branch, then can merge to master branch)
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
3 03/01/2020 03/07/2020
  • Decide on sensors (4 ultrasonic sensors: 3 in front, 1 in back)
  • Decide on a GPS module (Adafruit ADA746)
  • Research GPS antennas
  • Decide on CAN transceivers (SN65HVD230 IC's)
  • Request 15 CAN transceiver samples from ti.com
  • Discuss tasks of all 4 board nodes (geographical, driver, motors, bridge controller/sensors)
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
4 03/08/2020 03/14/2020
  • Assemble car chassis and plan general layout
  • Delegate tasks for each 2 person teams
  • Create branches for all nodes and add motor and sensor messages to DBC file
  • Discuss and research possible GPS antennas
  • Design block diagrams for motor node, bridge controller/sensor node, and full car
  • Solve GitLab branches vs folders issue (1 branch per node, or 1 folder per node)
  • Order 4 + 1 extra ultrasonic sensors (MaxBotix MB1003-000 HRLV-MaxSonar-EZ0)
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
5 03/15/2020 03/21/2020
  • Decide what to include on PCB board
  • Read previous student's reports to decide on a compass module (CMPS14)
  • Order GPS antenna
  • Add GPS node messages (longitude, latitude, heading) and bridge sensor node messages (destination latitude and longitude) to DBC file
  • Start learning Android app development
  • Begin researching filtering algorithms for ultrasonic sensors
  • Ultrasonic sensor values are converted to centimeters and transmit to driver node
  • Research ultrasonic sensor mounts
  • Transmit CAN messages from sensor to driver node, and from driver to motor node
  • Driver node is able to respond correctly based on sensor obstacle detection scenarios (correct LED's light up)
  • Decide movement and steering directions based on all possible sensor obstacle detection scenarios
  • Begin research on PID implementation to control speed of RC car
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
6 03/22/2020 03/28/2020
  • Draw block diagrams with pin information for each board and begin PCB design based on these diagrams
  • Order a new compass module (CMPS14)
  • Finalize parts list and place orders for remaining unordered items
  • Decide on tap plastic acrylic sheet dimensions and PCB dimensions
  • Start implementing a basic Android app without Google maps API and create a separate GitLab repo for app
  • Bridge sensor node is able to transmit a destination latitude and longitude coordinates message to geological node
  • Decide on ultrasonic sensor mounts and order extra if needed
  • Geological node is able to transmit a heading message to the driver node
  • Integrate driver board diagnostic testing with LEDs and ultrasonic sensors (car goes left, left LEDs light up, etc.)
  • Continue research on PID controller design and begin basic implementation
  • Finish designing team logo and upload to Wiki page
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
7 03/29/2020 04/04/2020
  • Complete rough draft of DBC file messages and signals
  • Purchase tap plastic acrylic sheet
  • Learn how to integrate Google maps API into Android app
  • Finish a basic implementation of filtering ultrasonic sensor's ADC data
  • Design a block diagram for optimal ultrasonic sensor placement
  • Bluetooth Module driver is finished, can connect to Android phone, and can receive "Hello World" data from phone
  • Geological node is able to parse the GPS NMEA string to extract latitude and longitude coordinates
  • Geological node is able to receive a current heading (0-360 degrees) from the compass module
  • Geological node is able to receive an NMEA string from the GPS
  • Geological node is able to compute the destination heading (0-360 degrees) and send to driver node
  • Add PWM functionality to motor board code and test on DC and servo motors
  • Complete a basic implementation of encoder code on motor board
  • Complete rough draft of schedule and upload to Wiki page
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
8 04/05/2020 04/11/2020
  • Google maps API is fully integrated into Android App
  • Finish ultrasonic filtering algorithm for ultrasonic sensor's ADC data
  • Design ultrasonic sensor shields to minimize sensor interference with each other
  • Bluetooth Module is able to receive data from Android app
  • Test obstacle avoidance algorithm (indoor)
  • Complete motor board code controlling RC car's DC motor and servo motor
  • Complete "push button" motor test (servo turns wheels left and right, and DC motor spins wheel forwards and backwards)
  • Begin car chassis wiring on a breadboard
  • Finalize and review PCB schematic
  • Complete a rough draft car chassis block diagram for the placement of all boards and modules
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
9 04/12/2020 04/18/2020
  • Discuss checkpoint algorithm
  • Display sensor and motor data on Android app
  • Bluetooth module is able to receive "dummy" destination latitude and longitude coordinates from Android app
  • Finish GPS module integration with geographical controller
  • Test obstacle avoidance algorithm (outdoor)
  • Test existing motor board code on RC car's motors
  • Begin wheel encoder implementation and unit testing
  • Complete car chassis wiring on a breadboard
  • Establish and test CAN communication between all boards
  • Design and solder a prototype PCB board in case PCB isn't delivered in time
  • Mount sensors, motors, LCD, and all four sjtwo boards onto car chassis
  • Finish routing PCB and review to verify the circuitry
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
10 04/19/2020 04/25/2020
  • Android app is able to send start and stop commands to the car
  • Android app is able to display car data (speed, sensor values, destination coordinates, source coordinates)
  • Bluetooth module is able to receive actual destination latitude and longitude coordinates from Android app
  • Test drive outdoors to check obstacle avoidance algorithm
  • Complete motor control code with optimal speed and PWM values without PID control
  • Begin unit testing the PID control algorithm
  • Finish wheel encoder implementation and unit testing
  • Make final changes to PCB and place order
  • Test drive the soldered PCB board to ensure everything is working properly
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
11 04/26/2020 05/02/2020
  • Test drive from start to destination (outdoor)
  • GEO controller can compute the heading from Android app's actual destination coordinates, and send to driver board
  • Finalize obstacle avoidance algorithm
  • LCD display is able to display car's speed, PWM values, destination coordinates, and sensor values
  • Complete a basic PID algorithm and begin uphill and downhill testing
  • Fully integrate wheel encoder onto car chassis
  • Finish basic implementation of PID control and test on car
  • Solder and integrate PCB onto car and test drive to make sure everything is working properly
  • Mount GPS and compass modules onto car chassis
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
12 05/03/2020 05/09/2020
  • Test drive from start to destination with obstacles and making U-turns (outdoor)
  • Finalize DBC file
  • Complete Android app's basic features (start, stop, connect, google maps, displaying car data)
  • Begin implementing additional Android app features (extra screen to display car data, checkpoint selection capability) and improving the look of the UI
  • Finalize sensor shields and mounting heights/positions
  • Design and 3D print front sensor stand
  • Complete basic implementation and unit testing of checkpoint algorithm
  • Test checkpoint algorithm on car (outdoor)
  • Finalize PID control implementation and test on car (outdoor)
  • Integrate GPS antenna onto car chassis
  • Drill acrylic sheet and mount circuity with screws instead of glue
  • Completed
  • Completed
  • Completed
13 05/10/2020 05/16/2020
  • Test drive from start to destination on 10th Street garage and determine checkpoints
  • Finalize Android app's checkpoint selection capability, display car data screen, and UI improvements
  • Finalize checkpoint algorithm based on feedback from test drives
  • Tweak obstacle avoidance algorithm based on feedback from test drives
  • Tweak PID control implementation based on feedback from test drives
  • Upload rough draft of report to Wiki page
14 05/17/2020 05/23/2020
  • Test drive from start to destination on 10th Street garage
  • Demo
  • Push final code to GitLab
  • Submit individual contributions feedback for all team members
  • Make final updates to Wiki report


Parts List & Cost

Item# Part Desciption Vendor Qty Cost
1 RC Car Chassis Traxxas 1 $250.00
2 Lithium-Ion Battery 1
3 Battery Charger 1
4 Tap Plastics Acrylic Sheet 1
5 Ultrasonic Sensors Amazon [2] 4
6 GPS Module 1
7 GPS Antenna 1
8 Compass Module 1
9 UART LCD Display 1
10 Bluetooth Module 1
11 CAN Transceivers SN65HVD230DR 15 Free Samples
12 Sjtwo Board Preet 4 $50.00
13 12" Pipe 1
14 Android Mobile Phone 1
15 Sensor Mounts 4


Hardware Integration:- Printed Circuit Board


We Initially started with a very basic design of mounting all the hardware on a cardboard sheet for our first round of Integrated hardware testing.

First Prototype Board


Challenges:- The wires were an entire mess and the car could not navigate properly due to the wiring issues as all the wires were entangling and few had connectivity issues. Hence we decided to go for a basic dot matrix Design before finalizing our final PCB Design as a Prototype board for testing if anything goes haywire.

The Prototype Board just before the actual PCB board was created on a dot matrix PCB along with all the hardware components for the Intermediate Integrated testing phase is as follows:

Prototype board 1
Prototype board 2
Prototype board 3


1) To avoid all the above challenges We designed the custom PCB using EasyEDA in which we implemented connections for all the controller modules(SJTwo Board LPC4078) all communicating/sending data via CAN bus. The data is sent by individual sensors to the respective controllers. GPS and Compass are connected to Geographical Controller. RPM sensor, DC and Servo Motors are connected to Motor Controller.
2) Ultrasonic are connected to Bridge and Sensor Controller. LCD is connected to Driver Controller. Bluetooth is connected to Bridge and Sensor Controller. CAN Bus is implemented using CAN Transceivers SN65HVD230 terminated by 120 Ohms; with PCAN for monitoring CAN Debug Messages and Data. Some Components need 5V while some sensors worked on 3.3V power supply. Also it was difficult to use separate USB's to power up all boards.Hence we used CorpCo breadboard power supply 3.3V/5V.
3) PCB was sent to fabrication to JLCPCB China which provided PCB with MOQ of 5 with the lead time of 1 week. We implemented 2 layers of PCB with most of the parts in top layer GPS sensor and Compass sensor. We implemented rectangular header connector for SJTwo boards, RPM sensor, DC & Servo Motor on the bottom layer. There were 2 iterations of this board.
4) Challenges :-We also need to change the header for LCD since it was having different pitch.


DESIGNING:-

Top Layer development
Bottom Layer development

AFTER DELIVERY:-

Top Layer development
Bottom Layer development






CAN Communication

<Talk about your message IDs or communication strategy, such as periodic transmission, MIA management etc.>

Hardware Design

<Show your CAN bus hardware design>

DBC File

DBC File




Bridge and Sensor Controller

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Motor Controller

The Motor Controller SJ2-Board is mainly responsible for RC-Car’s steering and speed to move the car towards the destination. The RC-Car we are using is 2 Wheel Drive which means the front wheels are used for steering which is controlled by servo motor and the rear wheels are used for car’s forward and reverse movements which are controlled by DC Motor through ESC.

Hardware Design

<Motor_Module_Schematic.png>
Bucephalus Logo


ESC & DC Motor

<esc.jpg> <motor.jpg>


The ESC(Electronic Speed Control, Traxxas ESC XL-05) and DC Motor we used were provided with the RC car. The DC motor is controlled by ESC using PWM signals provided by the motor controller for forward and reverse movements. We used the 7.4v LiPo battery to power up the ESC. The DC motor is powered by the ESC which has a dc-to-dc converter which converts 7.4v to 6v. ESC can provide high current to the power-hungry DC motor running at faster speeds. ESC has an LED and a button which is used for calibration and setting different modes for the car.

The car can be operated in the following 3 modes: Sport mode(100% Forward, 100% Brakes, 100% Reverse) Racing mode(100% Forward, 100% Brakes, No Reverse) Training mode(50% Forward, 100% Brakes, 50% Reverse)

As we needed more than 50% speed for steep ramps, we used Sport mode. The frequency of the PWM signal fed to the servo motor is 100Hz. Based on the duty cycle set by the user, the car will go forward, reverse, or neutral. 10% - 20% duty cycle for reverse. 15% duty cycle for neutral. 15%-20% duty cycle for the forward motion.

SERVO

<servo.jpg>

The servo motor we used is Traxxas 2075 which was provided with the car and it is responsible for steering the car. It takes the 6V power directly from ESC. The servo motor is controlled directly from the SJ2 micro-controller board. The PWM signal fed to the servo motor is of frequency 100Hz. Based on the duty cycle of the signal sent to the servo, it rotates in the left / right direction. 10% - 20% duty cycle for left. 15% duty cycle for straight. 15%-20% duty cycle for right.

RPM SENSOR

<rpm_sensor.jpg> <trigger_magnet.jpg>

There are two parts to the RPM sensor - one is the trigger magnet and the other is the sensor. The RPM sensor is used as an input to maintain a constant speed of the vehicle. The sensor mounts on the inside of the gear cover, the trigger magnet mounts on the DC motor shaft. The gear cover and motor shaft need to be removed using the toolkit provided along with the RC car. The procedure is similar to this video, but note that the car used in the video is a 4WD RC car by Traxxas. We made use of the trigger magnet attached to the spur gear to trigger a pulse on the sensor for every rotation of the spur gear. These pulses are then read by the SJ2 board to calculate rotations in a second and later convert it to RPM and MPH. The RPM sensor has 3 wires, the white wire is the output wire that provides the pulses to the SJ2 Board, and the other wires are Supply(6V) and GND. We also used a Pull Down 1K Resistor between Supply and RPM output wires.

Software Design

Periodic Callbacks:

Periodic Init: CAN, PWM(Servo and Motor), and Interrupts(RPM Sensor and Test button) were initialized in this function.

10Hz function: CAN messages were transmitted in this function. Also, Cleared wheel rotations every 500ms.

100Hz function: Used this function to run at 20Hz. When the test button is pressed, Motor tests are performed else the car will follow driver commands.

<Periodic_Callbacks_Flowchart.PNG>

Servo Motor:

The PWM signal fed to the servo motor is of frequency 100Hz. The motor controller receives steer controls from the driver controller and it sends corresponding PWM value to the servo motor.

<Steering_Flowchart.PNG>

DC Motor:

The PWM signal fed to the DC motor is of frequency 100Hz. The motor controller receives speed controls from the driver controller and it sends corresponding PWM value to the ESC which controls the DC motor.

<DC_Motor_Flowchart.PNG>

RPM Sensor:

RPM Sensor gives one pulse for each wheel rotation and the software calculates speed in mph using the no. of rotations. We are re-calculating the speed, every 500ms to maintain the speed of the motor while the car is going uphill or downhill.

<RPM_Sensor_Flowchart.PNG>

Technical Challenges

Car Reverse Movement

Problem: The RC car sometimes wouldn’t go reverse and this used to happen randomly.

Solution: We checked the code and were giving the correct PWM values for the car to go reverse but the car wouldn’t do it sometimes. Then, we read the ESC manual and figured out that the wheels need to stop before giving the reverse command. For us, using these Commands (FULL REVERSE and STOP) before giving reverse PWM values for the reverse movement worked well. Also, we had to use current speed in combination with these FULL REVERSE commands to make sure that these reverse commands are given only when the car is moving forward.

Car downhill movement

Problem: The car would move too fast while downhill even though the feedback loop for the speed control is reducing the PWM.

Solution: The feedback loop to maintain the speed of the car was working fine while the car was going uphill, but while downhill the car would go too fast. To resolve this, we applied brakes(FULL REVERSE commands) to the car whenever the speed crosses a certain limit.

Mounting the RPM Sensor

Problem: We had a hard time figuring out where to mount the rpm sensor, as the documentation provided by Traxxas was for 4WD and ours was a 2WD RC car.

Solution: We figured out the place to mount the sensor by chance, using common sense. It was mounted on the inside of the gear cover, where a tiny hidden place was provided.




Geographical Controller

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Driver Module

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Mobile Application

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>






Conclusion

This project taught us how to work with so many people with same goal but different working patterns to come together and execute their ideas together in tandem to accomplish the team goal. We developed an autonomously navigating RC car. Each team member brought unique skills, passions and personalities to the project. Some team people were skilled with designing and placing components on the PCB Board, while others were skilled in firmware development, project management, catching bugs, organizing meetings etc. Some people had the ability to lighten the mood on disappointing demo days, while others had the management skill to keep the team focused and making the car its best version than the day before, while avoiding burning the team out at each other. When these different minds and their skills came together, it resulted in the final product that we all are extremely proud of, as well as one that performed well on the final demo day. The shelter in place brought more challenges in coordination as we couldn't meet much for in person meetings and everyone needed the hardware for testing their code. It was difficult for a single person who had all the hardware to always test with few members or alone and to explain others where exactly their code was failing.

It wasn't always fun and lively though. We experienced soaring highs, during few of our progress demos, where we hit almost all of our specs. We also experienced devastating lows, when we were not able to demo properly as there were coordination issues offline at the start. While we look back fondly on our project, the reality is that it was the result of 7 graduate students spending almost every day of the semester developing and fine tuning the final product. We failed and succeeded together as a team. The goal was too important. Blame fell on the team as a whole and so did success and praise. We succeeded because we failed together. We succeeded because we didn't let failure break us and instead worked harder to fine tune and improve our test cases so that no case in the testing is left unexplored and the car worked exceptionally well.

There was so much to learn. Always something new, it felt like. We developed a clean and best working PCB, to integrate all of our subsystems together with least number of wires needed and visible on the car, even though none of us had experience developing a board that complex before. We also approached new challenges such as developing an Android Mobile Application, even though none of us knew JAVA or knew Android Studio beforehand. We never stopped learning. We learned the value of investing in quality components. We honed our unit testing skills, trying to write firmware that was as high quality as our hardware. We learned about CANbus on an intimate level and applied all of the knowledge. Testing at residential area gave us a tough time especially with the GPS module and the ultrasonic sensors as the google maps did not give us the exact co-ordinates of internal society roads. while the ultrasonic sensors faced difficulty in detecting low height sidewalks.

Working on this project was a difficult yet ultimately rewarding experience. It taught us how to make use of unit tests so that we don't need hardware at all and this helped alot in online coordination with team members. We can't stress enough how important is to start the project as early as possible in the semester and to keep pushing until the final demo. Each of contributed roughly 20 hours a week to work on the project. As a result, we were exhausted by the end of it, but we also never had to pull nights sometimes to meet the deadlines. We had excellent leadership from our team lead, Mohit Ingale, as well as our mentors, Preet and ISA members Aakash, Vignesh. We also had excellent peers in CMPE 243 and are proud of what they achieved as well. Overall, we were happy to be part of this class and we hope that our project will inspire future students to develop electric vehicles.


Project Video

Project Source Code

Advise for Future Students

  • FORM YOUR TEAM AS EARLY AS POSSIBLE AND START WORKING ON THE PROJECT AS EARLY AS POSSIBLE Dont't go by the team size. There is lot of work which keeps on stalking up and then can haunt us in the end of semester.
  • If you are having trouble with your GPS or compass, ultrasonic(due to more obstacles at residential areas) try testing on top of one of the SJSU parking garages on a weekend. There is much less signal interference.
  • Order spare parts and all parts before hand so that you don't keep running around at last moment. You will encounter defective parts and shipping wastes time and increases stress (especially nearing demo day)
  • Make sure to get a power supply doesn't bun you board's fuse and supplies current less than 1A. When all the car's subsystems are running, the current draw may be higher than expected
  • Don't go for cheap modules and car model from Ebay, those will probably waste more of your time and probably cost you more at the end as you might end up buying hardware again. Get quality modules and they will pay for themselves down the road.
  • Make use of all the holidays specially Spring break as there are assignments from other classes too and this would be the best time when probably everyone can be free. This will save you on the final DEMO day.
  • Getting access to a 3D printer can be very useful for this project, with which you can customize sensor mounts, car hood.
  • Take advantage of the code reviews that Preet offers! They will fix a lot of bugs in your code and will make it a lot easier to manage each module.