Difference between revisions of "S16: Expendables"

From Embedded Systems Learning Academy
Jump to: navigation, search
(Software Design)
(Project Source Code)
 
(88 intermediate revisions by the same user not shown)
Line 1: Line 1:
=== Grading Criteria ===
+
== Wireless LED Text Display ==
<font color="green">
+
[[File:CMPE244_S16_Expendables_Animation.gif|600px|thumb|centre]]
*  How well is Software & Hardware Design described?
 
*  How well can this report be used to reproduce this project?
 
*  Code Quality
 
*  Overall Report Quality:
 
**  Software Block Diagrams
 
**  Hardware Block Diagrams
 
**:  Schematic Quality
 
**  Quality of technical challenges and solutions adopted.
 
</font>
 
 
 
== Project Title ==
 
  
 
== Abstract ==
 
== Abstract ==
This section should be a couple lines to describe what your project does.
+
Wireless LED text display allows users to display text from anywhere using internet. Wireless text display scrolls the multicolored text message on the serially connected LED panels. To enable the wireless transmission, the webapp is accessing the IP address to which the raspberry pi is connected. Project explores the idea of displaying a text message conveniently from any place over internet.
  
 
== Objectives & Introduction ==
 
== Objectives & Introduction ==
Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.
+
The focus of the project is to develop an embedded design to display message wirelessly on the LED panels. Internet is selected as the medium to send the message wirelessly. Webapp is developed to provide the text input. On the Hardware side, Raspberry pi is connected to internet either by Wi-Fi or Ethernet. The Text sent from the webapp is received by Raspberry pi. Raspberry pi transmits the data serially through UART to SJ-ONE board. SJ-ONE board consists of code to drive the LED panels and connects to LED panels through PCB interface. PCB board consists of Lever shifter buffer IC required to protect SJ-ONE board GPIO pins and level shift the signals.
  
=== Team Members & Responsibilities ===
+
The Objectives of the Project are as follows:<br>
*[https://www.linkedin.com/in/asmita-deshpande-ba93b1100 Asmita Deshpande]<br>
+
1. Driving a single LED panel without any built-in controller through GPIO.<br>
+
2. Driving multiple LED panels, which are connected serially.<br>
*[https://www.linkedin.com/in/sameenameer Sameena Meer]<br>
+
3. SJONE board connection with LED panels.<br>
 +
4. PCB board creation to drive the voltage levels of 3.3v SJONE board and 5.0V LED panel.<br>
 +
5. Raspberry pi connection with the SJONE board.<br>
 +
6. Webapp creation to send the text message to raspberry pi.<br>
  
*[http://www.linkedin.com/in/samiullah2 Sami Ullah]<br>
+
[[File:CMPE244_S16_Expendables_Block Diagram of the system.png|600px|thumb|centre|Block diagram of the system]]
  
*[https://www.linkedin.com/in/sant-prakash-soy-93898022 Sant Soy]<br>
+
=== Team Members & Responsibilities ===
 +
*[https://www.linkedin.com/in/asmita-deshpande-ba93b1100 Asmita Deshpande] and [https://www.linkedin.com/in/sameenameer Sameena Meer]<br>
 +
**Raspberry Pi Setup
 +
**UART Setup
 +
**Python Magic
 +
**PCB Debugging
 +
**Soldering
 +
*[https://www.linkedin.com/in/samiullah2 Sami Ullah] and [https://www.linkedin.com/in/sant-prakash-soy-93898022 Sant Prakash Soy]<br>
 +
**AWS Server
 +
**MQTT
 +
**PCB Design
 +
**LED Driver
  
 
== Schedule ==
 
== Schedule ==
Line 52: Line 55:
 
|3/20/2016
 
|3/20/2016
 
|LED panels study  
 
|LED panels study  
|Ongoing
+
|Completed
|
+
|3/20/2016
 
|-
 
|-
 
|-
 
|-
Line 60: Line 63:
 
|4/03/2016
 
|4/03/2016
 
|Raspberry Pi 3 study
 
|Raspberry Pi 3 study
|
+
|Completed
|
+
|4/03/2016
 
|-
 
|-
 
|-
 
|-
Line 68: Line 71:
 
|4/10/2016
 
|4/10/2016
 
|Pixel Driver Design
 
|Pixel Driver Design
|
+
|Completed
|
+
|4/20/2016
 
|-
 
|-
 
|-
 
|-
Line 84: Line 87:
 
|4/24/2016
 
|4/24/2016
 
|Testing Text Display
 
|Testing Text Display
|
+
|Completed
|
+
|4/20/2016
 
|-
 
|-
 
|-
 
|-
 
|7
 
|7
|5/25/2016
+
|4/25/2016
 
|5/01/2016
 
|5/01/2016
 
|UI Webserver
 
|UI Webserver
|
+
|Completed
|
+
|4/25/2016
 
|-
 
|-
 
|-
 
|-
Line 100: Line 103:
 
|5/08/2016
 
|5/08/2016
 
|Final Testing and Debugging  
 
|Final Testing and Debugging  
|
+
|Completed
|
+
|5/21/2016
 
|-
 
|-
 
|-
 
|-
Line 107: Line 110:
  
 
== Parts List & Cost ==
 
== Parts List & Cost ==
Give a simple list of the cost of your project broken down by componentsDo not write long stories here.
+
 
 +
{| class="wikitable"
 +
|-
 +
! scope="col"| Sl. No
 +
! scope="col"| Part Name
 +
! scope="col"| Source of purchase
 +
! scope="col"| Quantity
 +
! scope="col"| Cost($)
 +
|-
 +
|-
 +
|1
 +
|Raspberry Pi 3
 +
|[https://www.adafruit.com/products/3055 Adafruit]
 +
|1
 +
|44.49
 +
|-
 +
|-
 +
|2
 +
|LED panels
 +
|Preet
 +
|4  
 +
|0
 +
|-
 +
|-
 +
|3
 +
|74HC245
 +
|[https://www.digikey.com/product-detail/en/fairchild-semiconductor/MM74HC245AN/MM74HC245AN-ND/243 Digikey]
 +
|2
 +
|2
 +
|-
 +
|-
 +
|4
 +
|ATX PSU
 +
|[https://www.amazon.com/Logisys-480W-4-pin-Power-Supply/dp/B000F0DUT8 Amazon]
 +
|1
 +
|20.94
 +
|-
 +
|-
 +
|5
 +
|Molex Connectors
 +
|[https://www.amazon.com/Molex-4-Pin-Connector-0-093-quot/dp/B0009WBHLK/ref=sr_1_fkmr1_2?s=pc&ie=UTF8&qid=1463720920&sr=8-2-fkmr1&keywords=empty+Molex+connectors Amazon]
 +
|4
 +
|15
 +
|-
 +
|-
 +
|6
 +
|PCB
 +
|[https://oshpark.com/ OSH Park]
 +
|3
 +
|30
 +
|-
 +
|-
 +
|7
 +
|Aluminum Extrusion
 +
|[https://www.adafruit.com/product/1221 Adafruit]
 +
|1
 +
|7.50
 +
|-
 +
|-
 +
|8
 +
|Oval T-Nut
 +
|[https://www.adafruit.com/products/1158 Adafruit]
 +
|50
 +
|9.95
 +
|-
 +
|-
 +
|9
 +
|Power Adapter for Raspberry PI
 +
|[https://www.amazon.com/CanaKit-Raspberry-Supply-Adapter-Charger/dp/B00MARDJZ4?ie=UTF8&keywords=Raspberry%20PI%203%20adapter&qid=1463866723&ref_=sr_1_1&sr=8-1 Amazon]
 +
|1
 +
|9.99
 +
|-
 +
|-
 +
|}
  
 
== Design & Implementation ==
 
== Design & Implementation ==
  
 
=== Hardware Design ===
 
=== Hardware Design ===
====LED Panels====
+
====LED Panels Working====
 
[[File:CMPE244_S16_Expendables_LED_Panel_Front.png|640px|thumb|centre|LED Panel Front]]
 
[[File:CMPE244_S16_Expendables_LED_Panel_Front.png|640px|thumb|centre|LED Panel Front]]
 
The display panels use multiplexing to draw picture information, which means that the rows and columns are updated fast than the human eye can process. If the updating speed is fast enough, eyes will see a complete picture without flickering. The updating process is as follows
 
The display panels use multiplexing to draw picture information, which means that the rows and columns are updated fast than the human eye can process. If the updating speed is fast enough, eyes will see a complete picture without flickering. The updating process is as follows
Line 149: Line 225:
 
For drawing 16 rows using the 8 outputs of the decoder, we must have unique data for each row pair. When Row 1 and Row 9 are selected, we must provide each row with unique data. This forces us to use two different shift registers for each row pair, an upper register and a lower register. Because of this, the display is divided into an upper half and a lower half. The data is shifted into the top half via the R1, G1 and B1 signals on the connector. The bottom half’s data is supplied by the R2, G2 and B2 signals on the connector. Then, since our display is 32 pixels wide, we must use 2 shift registers to hold all 32 bits of pixel data for a single row. This creates the left and right halves of the display.
 
For drawing 16 rows using the 8 outputs of the decoder, we must have unique data for each row pair. When Row 1 and Row 9 are selected, we must provide each row with unique data. This forces us to use two different shift registers for each row pair, an upper register and a lower register. Because of this, the display is divided into an upper half and a lower half. The data is shifted into the top half via the R1, G1 and B1 signals on the connector. The bottom half’s data is supplied by the R2, G2 and B2 signals on the connector. Then, since our display is 32 pixels wide, we must use 2 shift registers to hold all 32 bits of pixel data for a single row. This creates the left and right halves of the display.
 
Each quadrant of the display is controlled by 3 shift registers, one for each color. First, Row 1 and Row 9 are selected. 32 bits of data are shifted into each color’s shift register (R1, G1, B1), and then latched. At the same time, 32 bits of data are also shifted into each color’s shift register for the bottom half (R2, G2, B2), and then latched. The process repeats 7 more times, each time incrementing which rows are selected, until every line has been updated.
 
Each quadrant of the display is controlled by 3 shift registers, one for each color. First, Row 1 and Row 9 are selected. 32 bits of data are shifted into each color’s shift register (R1, G1, B1), and then latched. At the same time, 32 bits of data are also shifted into each color’s shift register for the bottom half (R2, G2, B2), and then latched. The process repeats 7 more times, each time incrementing which rows are selected, until every line has been updated.
 +
 +
[[File:CMPE244_S16_Expendables_LED_Panel_Schematic.png|600px|thumb|centre|Conceptual Schematic]]
 +
 +
In summary in order to display something on the LED panels the following steps needs to be performed by the driver
 +
 +
*Shift the pixel data for row 0 into the top column drivers and the pixel data for row 16 into the bottom column drivers using the R1, G1, B1, R2, G2, and B2 data inputs and the SCLK shift clock signal.
 +
*Assert the blanking signal to blank the display.
 +
*Set the address input to 0.
 +
*Latch the contents of the column drivers‘ shift registers into the column drivers‘ output registers using the LATCH signal.
 +
*De-assert the blanking signal to display rows 0 and 16.
 +
*Wait some fixed amount of time.
 +
*Repeat the process for each of the pairs of rows in the display.
 +
*Repeat the entire process at least 100 to 200 times per second to prevent flicker.
  
 
=== Hardware Interface ===
 
=== Hardware Interface ===
 
The connector on the RGB panels is called a Hub75 interface. Each panel typically has two ports, one is the input and the other is the output to chain additional panels.
 
The connector on the RGB panels is called a Hub75 interface. Each panel typically has two ports, one is the input and the other is the output to chain additional panels.
  
[[File:CMPE244_S16_Expendables_LED_Panel_Interface.jpg|600px|thumb|centre|LED Panel Interface]]
+
[[File:CMPE244_S16_Expendables_LED_Panel_Interface.jpg|500pxx250px|thumb|centre|LED Panel Interface]]
  
 
====PCB Design====
 
====PCB Design====
Line 161: Line 250:
  
 
  [[File:CMPE244_S16_Expendables_Board.PNG|400px|thumb|centre|PCB of Board]]
 
  [[File:CMPE244_S16_Expendables_Board.PNG|400px|thumb|centre|PCB of Board]]
 +
 +
[[File:CMPE244_S16_Expendables_PCB_1.png|400px|thumb|centre|PCB of Board]]
 +
 +
 +
[[File:CMPE244_S16_Expendables_PCB_2.png|400px|thumb|centre|PCB of Board]]
  
 
=== Software Design ===
 
=== Software Design ===
 +
 +
====Classes====
 +
 +
The software for driving the LED panels is divided into two classes, '''GFX''' and '''RGB'''. The GFX class implements all the methods for drawing various characters on the LED panels, setting their heights, and colors. It does not concerns with how the LED panel works, and just assumes the LED panels to be a '''canvas''' to draw on. The GFX class has '''virtual functions''', which deals with how to actually display something on he panels. These virtual functions are implemented in the RGB class, which inherits from GFX class.
 +
 +
[[File:CMPE244_S16_Expendables_Software_Classes.png‎|322px|thumb|centre|Classes]]
 +
 +
====Tasks====
 +
 +
Further there are three tasks to get the LED panel running, and displaying the required task. The first task is '''setuppanel''', which has a low priority. This task only runs once, and sets all the parameters like text size, wrap, etc. The second task called '''panel''' runs continuously, and has high priority because it is responsible for displaying the text and refreshing the LED panels. The third task is simply called '''gpioTask''', it is a medium priority task, and is reponsible for receiving the text to display over UART from raspberry PI.
 +
 +
[[File:CMPE244_S16_Expendables_Software_Tasks.png‎|543px|thumb|centre|Tasks]]
 +
 +
====Web Application====
 +
 +
A webapp was designed hosted on Amazon AWS. The raspberry pi connects to the service provided by the webapp, any text entered on the webapp is transmitted to raspberry pi, which sends the received text over UART to the SJONE board to be displayed on the LED panels.
 +
 +
[[File:CMPE244_S16_Expendables_Webpage_1.png|600px|thumb|centre|Login Page]]
 +
 +
[[File:CMPE244_S16_Expendables_Webpage_2.png|600px|thumb|centre|Text Entry Page]]
 +
 +
[[File:CMPE244_S16_Expendables_Flowchart of Webpage.JPG|200px|thumb|centre|Input Text Flow from Webpage to LED panels]]
 +
 +
[http://52.37.101.139:5000/login Visit the Website]
 +
 +
=== Implementation ===
 +
 +
====Fonts====
 +
The fonts displayed on the LED panels are implemented as an array of hexadecimal values, and in alphabetical order.
 +
 +
 +
This section includes implementation, but again, not the details, just the high level.  For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash.  You can include sub-sections for each of your component implementation.
 +
 +
====PWM====
 
The code tries to use a technique called Binary Code Modulation to control the colors of the display. Driving with Pulse Width Modulation (PWM) would turn the LED on for an amount of time proportional to the desired brightness, then turn it off for the rest of the period. BCM divides the period into binary-length segments (1x, 2x, 4x, etc), and turns the LED on or off for each of these segments according to the bits of the LED’s desired brightness.
 
The code tries to use a technique called Binary Code Modulation to control the colors of the display. Driving with Pulse Width Modulation (PWM) would turn the LED on for an amount of time proportional to the desired brightness, then turn it off for the rest of the period. BCM divides the period into binary-length segments (1x, 2x, 4x, etc), and turns the LED on or off for each of these segments according to the bits of the LED’s desired brightness.
 
The pixel data must be divided up into bitplanes. These bitplanes are nothing but an array in which each element is a single bit from a color value in the displayed image. Each pixel would require three separate bitplanes, one for each color element. However to drive the display, all three colors are written out for two different pixels at the same time. The code stores six bits, one from each bitplane, together in a byte. This way the bytes are immediately ready to be written to the GPIO port during the interrupt. The code refers to the arrays of ready-to-write bytes as “planes,”.
 
The pixel data must be divided up into bitplanes. These bitplanes are nothing but an array in which each element is a single bit from a color value in the displayed image. Each pixel would require three separate bitplanes, one for each color element. However to drive the display, all three colors are written out for two different pixels at the same time. The code stores six bits, one from each bitplane, together in a byte. This way the bytes are immediately ready to be written to the GPIO port during the interrupt. The code refers to the arrays of ready-to-write bytes as “planes,”.
 
In each interrupt (RGB::updateDisplay) a byte from the appropriate plane is written out to the GPIO port and the delay until the next interrupt is set.
 
In each interrupt (RGB::updateDisplay) a byte from the appropriate plane is written out to the GPIO port and the delay until the next interrupt is set.
  
void refreshISR(void)
+
[[File:CMPE244_S16_Expendables_Bitplanes.png|400px|thumb|centre|Bitplanes]]
{
+
 
  activePanel->updateDisplay();
+
  void refreshISR(void)
}
+
  {
 +
    activePanel->updateDisplay();
 +
  }
 +
 
 +
[[File:CMPE244_S16_Expendables_Flow.png|600px|thumb|centre|Flow]]
 +
 
 +
====Messaging Protocol====
 +
MQTT (Message Queue Telemetry Transport) is the messaging protocol used for sending text from our webapp to the LED panels.
 +
MQTT is a light weight messaging protocol that uses publisher and subscriber architecture.
 +
Publishers are the devices that send data and subscribers are the ones that receive data.
 +
Devices that need to receive data must have MQTT client program such as Eclipse Paho running on them.
 +
Furthermore, the client program running on these devices need to subscribe to topics from which they want to receive data.
 +
The devices that need to send data also must have Paho MQTT client running on them.
 +
To send data, devices have to publish data to certain topics.
 +
There is another program that sits in between the sending and the receiving devices which is called an MQTT broker.
 +
The job of an MQTT broker is to receive data from senders and then send the data to receivers with appropriate topics.
 +
 
 +
The figure below shows our MQTT messaging protocol architecture.
 +
The architecture shows an eclipse Paho client program, running on AWS (Amazon Web Service), is publishing text on a topic called "my_text_topic".
 +
It also shows the Paho client program running on raspberry pi subscribing to the topic "my_text_topic".
 +
The MQTT broker known as Mosquitto running on AWS receives text from the publisher publishing on topic "my_text_topic" and sends the data to the receiver that has already subscribed to topic "my_text_topic".
  
=== Implementation ===
+
  [[File:CMPE244_S16_Expendables_MQTT Messaging Protocol Architecture.PNG|600px|thumb|centre|MQTT Messaging Protocol Architecture]]
This section includes implementation, but again, not the details, just the high level.  For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.
 
  
 
== Testing & Technical Challenges ==
 
== Testing & Technical Challenges ==
Line 181: Line 328:
 
Include sub-sections that list out a problem and solution, such as:
 
Include sub-sections that list out a problem and solution, such as:
  
=== My Issue #1 ===
+
=== Issue #1: No Datasheets  ===
Discuss the issue and resolution.
+
The RGB LED panels we used did not have any datasheets available for them, this was worsened by the fact that they also did not have a standard interface to drive them like SPI or I2C. We decided to resolve this by studying the datasheets of the integrated circuits which were on the panels, but soon we bumped into another problem. The IC's were made by an obscure manufacturer called "CHIPONE".
 +
 
 +
[[File:CMPE244_S16_Expendables_IC.png|400px|thumb|centre|Integrated Circuits on the Panel]]
 +
 
 +
=== Issue #2: Raspberry PI 3  ===
 +
Initially we planned to use a PI 3 because of its built-in wifi capability, but while testing it we found out that it was very unstable, and was unable to have a consistent connection. Therefore we decided to use PI 2, and share the internet connection over Ethernet through a laptop.
 +
 
 +
=== Issue #3: Shapes and Graphics  ===
 +
 
 +
Though we were successfully able to display text on the display panels. We were unable to display images. The images would require extra effort on the transmission side, as the panels are very low resolution, so whatever image has to be displayed will need to be converted to a lower resolution first.
  
 
== Conclusion ==
 
== Conclusion ==
Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?
+
In this project we were given a set of RGB LED matrix to design something useful out of it. In the early parts of this project, our vague goals led to a broad scope of ideas, and a lack of structure. Choosing areas of focus helped us to narrow our design and choose an approach that is
 +
feasible.
 +
Many aspects of this project involved learning how particular processes work, including the PCB layout in eagle, performing DRC on it, sending it to a PCB house (OSHPARK), and making sure it fulfills all the restrictions imposed by them to have a working PCB. It also helped us learn about virtual classes, and polymorphism both of which our software utilizes.
 +
The design goals that we set for ourselves were completed, though there is much that can be improved upon. We have laid the foundation on which future projects can be done like displaying shapes, and images on the panel. In proving our concept, and designing a system that solves the problems we were presented with, however, we feel we have achieved success.
  
 
=== Project Video ===
 
=== Project Video ===
Upload a video of your project and post the link here.
+
[https://youtu.be/yWz8xx2hrJA YouTube]
  
 
=== Project Source Code ===
 
=== Project Source Code ===
[https://sourceforge.net/projects/sjsu/files/CmpE_S2016/ Sourceforge Source Code Link]
+
[[File:CMPE244_S16_Expendables_Wireless_ LED_Text_Display.zip|Wireless_ LED_Text_Display Project Code]]
  
 
== References ==
 
== References ==
 
=== Acknowledgement ===
 
=== Acknowledgement ===
Any acknowledgement that you may wish to provide can be included here.
+
We would like to thank Preet for the guidance and providing us LED Panels used in this project.
  
 
=== References Used ===
 
=== References Used ===
List any references used in project.
+
http://bikerglen.com/projects/lighting/led-panel-1up/<br>
 
+
http://www.batsocks.co.uk/readme/art_bcm_1.htm<br>
=== Appendix ===
+
http://flask.pocoo.org/<br>
You can list the references you used.
+
http://www.w3schools.com/

Latest revision as of 04:20, 23 May 2016

Wireless LED Text Display

CMPE244 S16 Expendables Animation.gif

Abstract

Wireless LED text display allows users to display text from anywhere using internet. Wireless text display scrolls the multicolored text message on the serially connected LED panels. To enable the wireless transmission, the webapp is accessing the IP address to which the raspberry pi is connected. Project explores the idea of displaying a text message conveniently from any place over internet.

Objectives & Introduction

The focus of the project is to develop an embedded design to display message wirelessly on the LED panels. Internet is selected as the medium to send the message wirelessly. Webapp is developed to provide the text input. On the Hardware side, Raspberry pi is connected to internet either by Wi-Fi or Ethernet. The Text sent from the webapp is received by Raspberry pi. Raspberry pi transmits the data serially through UART to SJ-ONE board. SJ-ONE board consists of code to drive the LED panels and connects to LED panels through PCB interface. PCB board consists of Lever shifter buffer IC required to protect SJ-ONE board GPIO pins and level shift the signals.

The Objectives of the Project are as follows:
1. Driving a single LED panel without any built-in controller through GPIO.
2. Driving multiple LED panels, which are connected serially.
3. SJONE board connection with LED panels.
4. PCB board creation to drive the voltage levels of 3.3v SJONE board and 5.0V LED panel.
5. Raspberry pi connection with the SJONE board.
6. Webapp creation to send the text message to raspberry pi.

Block diagram of the system

Team Members & Responsibilities

Schedule

Sl. No Start Date End Date Task Status Actual Completion Date
1 3/07/2016 3/13/2016 Components buying Completed 3/18/2016
2 3/14/2016 3/20/2016 LED panels study Completed 3/20/2016
3 3/28/2016 4/03/2016 Raspberry Pi 3 study Completed 4/03/2016
4 4/04/2016 4/10/2016 Pixel Driver Design Completed 4/20/2016
5 4/11/2016 4/17/2016 PCB Design Completed 3/30/2016
6 4/18/2016 4/24/2016 Testing Text Display Completed 4/20/2016
7 4/25/2016 5/01/2016 UI Webserver Completed 4/25/2016
8 5/02/2016 5/08/2016 Final Testing and Debugging Completed 5/21/2016

Parts List & Cost

Sl. No Part Name Source of purchase Quantity Cost($)
1 Raspberry Pi 3 Adafruit 1 44.49
2 LED panels Preet 4 0
3 74HC245 Digikey 2 2
4 ATX PSU Amazon 1 20.94
5 Molex Connectors Amazon 4 15
6 PCB OSH Park 3 30
7 Aluminum Extrusion Adafruit 1 7.50
8 Oval T-Nut Adafruit 50 9.95
9 Power Adapter for Raspberry PI Amazon 1 9.99

Design & Implementation

Hardware Design

LED Panels Working

LED Panel Front

The display panels use multiplexing to draw picture information, which means that the rows and columns are updated fast than the human eye can process. If the updating speed is fast enough, eyes will see a complete picture without flickering. The updating process is as follows

  • Select the row to be updated.
  • Output the desired column data on selected row.
Row Selection

Row selection is done by using a 3-to-8 address decoder (74HC138D). There are three address inputs to the display marked A, B and C. Based on the truth table, only one input is active (low) at a time.

Truth Table
Row Configuration

Since the panels has 16 rows, the 3-to-8 address decoder select rows in parallel. For example, when the 1st row (Row1) is selected, it also selects the 9th row (Row9). Using this technique implies that we must supply data for the columns for two unique rows at a time.

Rows with same name are selected together

The outputs of the decoder is connected to a P-Channel MOSFET, because the decoder itself can only handle low currents and cannot drive a row of LEDs directly. The P-Channel MOSFET provides the high current needed to drive a row of LEDs.

Output Mosfets

The decoder outputs are shared between every 8 outputs (1 and 9, 2 and 10, repeating that pattern until row 8 and 16).

Column Selection

The column data is stored in a 16-bit serial-in, parallel-out shift register. Since the display is 32 pixels wide, two shift registers must be chained together. The shift register is designed to work with LEDs and implements a constant-current system that ensures the LED brightness remains uniform. The panels that we are using utilize SCT2026 shift registers. These are 16-bit Serial-In/Parallel-Out registers.


Shift register block diagram

There are 12 of these shift registers on the display. 3 each are used to hold the Red, Green, and Blue data for 1 of 4 quadrants of the display. (3 colors * 4 quadrants = 12 chips)


The 4 quadrants


For drawing 16 rows using the 8 outputs of the decoder, we must have unique data for each row pair. When Row 1 and Row 9 are selected, we must provide each row with unique data. This forces us to use two different shift registers for each row pair, an upper register and a lower register. Because of this, the display is divided into an upper half and a lower half. The data is shifted into the top half via the R1, G1 and B1 signals on the connector. The bottom half’s data is supplied by the R2, G2 and B2 signals on the connector. Then, since our display is 32 pixels wide, we must use 2 shift registers to hold all 32 bits of pixel data for a single row. This creates the left and right halves of the display. Each quadrant of the display is controlled by 3 shift registers, one for each color. First, Row 1 and Row 9 are selected. 32 bits of data are shifted into each color’s shift register (R1, G1, B1), and then latched. At the same time, 32 bits of data are also shifted into each color’s shift register for the bottom half (R2, G2, B2), and then latched. The process repeats 7 more times, each time incrementing which rows are selected, until every line has been updated.

Conceptual Schematic

In summary in order to display something on the LED panels the following steps needs to be performed by the driver

  • Shift the pixel data for row 0 into the top column drivers and the pixel data for row 16 into the bottom column drivers using the R1, G1, B1, R2, G2, and B2 data inputs and the SCLK shift clock signal.
  • Assert the blanking signal to blank the display.
  • Set the address input to 0.
  • Latch the contents of the column drivers‘ shift registers into the column drivers‘ output registers using the LATCH signal.
  • De-assert the blanking signal to display rows 0 and 16.
  • Wait some fixed amount of time.
  • Repeat the process for each of the pairs of rows in the display.
  • Repeat the entire process at least 100 to 200 times per second to prevent flicker.

Hardware Interface

The connector on the RGB panels is called a Hub75 interface. Each panel typically has two ports, one is the input and the other is the output to chain additional panels.

LED Panel Interface

PCB Design

The LED panels use 74HC245 line drivers, these transceivers require 5v logic levels whereas the SJONE board only supports 3.3v logic. In order to drive the LED panels from 3.3v GPIO pins of the SJONE board, level-shifting IC is used to level shift signals from 3.3V to 5V and shield the SJONE board GPIOs from overloading. For this purpose, and to make it easier to connect the panels to the SJONE board a PCB was designed in EAGLE. The PCB attaches to GPIO pins of SJONE board and provides easily accessible, level-shifted output for the LED panels. The PCB also breaks-out free pins so that they can be used for other purposes.

Schematic Design
PCB of Board
PCB of Board


PCB of Board

Software Design

Classes

The software for driving the LED panels is divided into two classes, GFX and RGB. The GFX class implements all the methods for drawing various characters on the LED panels, setting their heights, and colors. It does not concerns with how the LED panel works, and just assumes the LED panels to be a canvas to draw on. The GFX class has virtual functions, which deals with how to actually display something on he panels. These virtual functions are implemented in the RGB class, which inherits from GFX class.

Classes

Tasks

Further there are three tasks to get the LED panel running, and displaying the required task. The first task is setuppanel, which has a low priority. This task only runs once, and sets all the parameters like text size, wrap, etc. The second task called panel runs continuously, and has high priority because it is responsible for displaying the text and refreshing the LED panels. The third task is simply called gpioTask, it is a medium priority task, and is reponsible for receiving the text to display over UART from raspberry PI.

Tasks

Web Application

A webapp was designed hosted on Amazon AWS. The raspberry pi connects to the service provided by the webapp, any text entered on the webapp is transmitted to raspberry pi, which sends the received text over UART to the SJONE board to be displayed on the LED panels.

Login Page
Text Entry Page
Input Text Flow from Webpage to LED panels

Visit the Website

Implementation

Fonts

The fonts displayed on the LED panels are implemented as an array of hexadecimal values, and in alphabetical order.


This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

PWM

The code tries to use a technique called Binary Code Modulation to control the colors of the display. Driving with Pulse Width Modulation (PWM) would turn the LED on for an amount of time proportional to the desired brightness, then turn it off for the rest of the period. BCM divides the period into binary-length segments (1x, 2x, 4x, etc), and turns the LED on or off for each of these segments according to the bits of the LED’s desired brightness. The pixel data must be divided up into bitplanes. These bitplanes are nothing but an array in which each element is a single bit from a color value in the displayed image. Each pixel would require three separate bitplanes, one for each color element. However to drive the display, all three colors are written out for two different pixels at the same time. The code stores six bits, one from each bitplane, together in a byte. This way the bytes are immediately ready to be written to the GPIO port during the interrupt. The code refers to the arrays of ready-to-write bytes as “planes,”. In each interrupt (RGB::updateDisplay) a byte from the appropriate plane is written out to the GPIO port and the delay until the next interrupt is set.

Bitplanes
 void refreshISR(void)
 {
   activePanel->updateDisplay();
 }
Flow

Messaging Protocol

MQTT (Message Queue Telemetry Transport) is the messaging protocol used for sending text from our webapp to the LED panels. MQTT is a light weight messaging protocol that uses publisher and subscriber architecture. Publishers are the devices that send data and subscribers are the ones that receive data. Devices that need to receive data must have MQTT client program such as Eclipse Paho running on them. Furthermore, the client program running on these devices need to subscribe to topics from which they want to receive data. The devices that need to send data also must have Paho MQTT client running on them. To send data, devices have to publish data to certain topics. There is another program that sits in between the sending and the receiving devices which is called an MQTT broker. The job of an MQTT broker is to receive data from senders and then send the data to receivers with appropriate topics.

The figure below shows our MQTT messaging protocol architecture. The architecture shows an eclipse Paho client program, running on AWS (Amazon Web Service), is publishing text on a topic called "my_text_topic". It also shows the Paho client program running on raspberry pi subscribing to the topic "my_text_topic". The MQTT broker known as Mosquitto running on AWS receives text from the publisher publishing on topic "my_text_topic" and sends the data to the receiver that has already subscribed to topic "my_text_topic".

MQTT Messaging Protocol Architecture

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

Issue #1: No Datasheets

The RGB LED panels we used did not have any datasheets available for them, this was worsened by the fact that they also did not have a standard interface to drive them like SPI or I2C. We decided to resolve this by studying the datasheets of the integrated circuits which were on the panels, but soon we bumped into another problem. The IC's were made by an obscure manufacturer called "CHIPONE".

Integrated Circuits on the Panel

Issue #2: Raspberry PI 3

Initially we planned to use a PI 3 because of its built-in wifi capability, but while testing it we found out that it was very unstable, and was unable to have a consistent connection. Therefore we decided to use PI 2, and share the internet connection over Ethernet through a laptop.

Issue #3: Shapes and Graphics

Though we were successfully able to display text on the display panels. We were unable to display images. The images would require extra effort on the transmission side, as the panels are very low resolution, so whatever image has to be displayed will need to be converted to a lower resolution first.

Conclusion

In this project we were given a set of RGB LED matrix to design something useful out of it. In the early parts of this project, our vague goals led to a broad scope of ideas, and a lack of structure. Choosing areas of focus helped us to narrow our design and choose an approach that is feasible. Many aspects of this project involved learning how particular processes work, including the PCB layout in eagle, performing DRC on it, sending it to a PCB house (OSHPARK), and making sure it fulfills all the restrictions imposed by them to have a working PCB. It also helped us learn about virtual classes, and polymorphism both of which our software utilizes. The design goals that we set for ourselves were completed, though there is much that can be improved upon. We have laid the foundation on which future projects can be done like displaying shapes, and images on the panel. In proving our concept, and designing a system that solves the problems we were presented with, however, we feel we have achieved success.

Project Video

YouTube

Project Source Code

File:CMPE244 S16 Expendables Wireless LED Text Display.zip

References

Acknowledgement

We would like to thank Preet for the guidance and providing us LED Panels used in this project.

References Used

http://bikerglen.com/projects/lighting/led-panel-1up/
http://www.batsocks.co.uk/readme/art_bcm_1.htm
http://flask.pocoo.org/
http://www.w3schools.com/