Difference between revisions of "S16: Expendables"

From Embedded Systems Learning Academy
Jump to: navigation, search
(Objectives & Introduction)
(Objectives & Introduction)
Line 20: Line 20:
 
The focus of the project is to develop an embedded design to display message wirelessly on the LED panels. Internet is selected as the medium to send the message wirelessly. Webpage is developed to provide the text input. On the Hardware side, Raspberry pi is connected to internet either by Wi-Fi or Ethernet. The Text sent from the webpage is received by Raspberry pi. Raspberry pi transmits the data serially through UART to SJ-ONE board. SJ-ONE board consists of code to drive the LED panels and connects to LED panels through PCB interface. PCB board consists of Lever shifter buffer IC required to protect SJ-ONE board GPIO pins and level shift the signals.
 
The focus of the project is to develop an embedded design to display message wirelessly on the LED panels. Internet is selected as the medium to send the message wirelessly. Webpage is developed to provide the text input. On the Hardware side, Raspberry pi is connected to internet either by Wi-Fi or Ethernet. The Text sent from the webpage is received by Raspberry pi. Raspberry pi transmits the data serially through UART to SJ-ONE board. SJ-ONE board consists of code to drive the LED panels and connects to LED panels through PCB interface. PCB board consists of Lever shifter buffer IC required to protect SJ-ONE board GPIO pins and level shift the signals.
  
The Objectives of the Project are as follows:
+
The Objectives of the Project are as follows:<br>
1. Driving a single LED panel without any built-in controller through GPIO.
+
1. Driving a single LED panel without any built-in controller through GPIO.<br>
2. Driving multiple LED panels, which are connected serially.
+
2. Driving multiple LED panels, which are connected serially.<br>
3. SJONE board connection with LED panels.
+
3. SJONE board connection with LED panels.<br>
4. PCB board creation to drive the voltage levels of 3.3v SJONE board and 5.0V LED panel.
+
4. PCB board creation to drive the voltage levels of 3.3v SJONE board and 5.0V LED panel.<br>
5. Raspberry pi connection with the SJONE board.
+
5. Raspberry pi connection with the SJONE board.<br>
6. Webpage creation to send the text message to raspberry pi.
+
6. Webpage creation to send the text message to raspberry pi.<br>
  
 
=== Team Members & Responsibilities ===
 
=== Team Members & Responsibilities ===

Revision as of 22:30, 21 May 2016

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Project Title

Abstract

Wireless text display scrolls the text message on the serially connected LED panels. Text display is multicolored. The text message is sent to the raspberry pi wirelessly from a webpage. Raspberry pi is connected to the SJONE board over a UART driver. To enable the wireless transmission, the webpage is accessing the IP address to which the raspberry pi is connected. Project explores the idea of displaying a text message conveniently from any place over internet.

Objectives & Introduction

The focus of the project is to develop an embedded design to display message wirelessly on the LED panels. Internet is selected as the medium to send the message wirelessly. Webpage is developed to provide the text input. On the Hardware side, Raspberry pi is connected to internet either by Wi-Fi or Ethernet. The Text sent from the webpage is received by Raspberry pi. Raspberry pi transmits the data serially through UART to SJ-ONE board. SJ-ONE board consists of code to drive the LED panels and connects to LED panels through PCB interface. PCB board consists of Lever shifter buffer IC required to protect SJ-ONE board GPIO pins and level shift the signals.

The Objectives of the Project are as follows:
1. Driving a single LED panel without any built-in controller through GPIO.
2. Driving multiple LED panels, which are connected serially.
3. SJONE board connection with LED panels.
4. PCB board creation to drive the voltage levels of 3.3v SJONE board and 5.0V LED panel.
5. Raspberry pi connection with the SJONE board.
6. Webpage creation to send the text message to raspberry pi.

Team Members & Responsibilities

Schedule

Sl. No Start Date End Date Task Status Actual Completion Date
1 3/07/2016 3/13/2016 Components buying Completed 3/18/2016
2 3/14/2016 3/20/2016 LED panels study Completed 3/20/2016
3 3/28/2016 4/03/2016 Raspberry Pi 3 study Completed 4/03/2016
4 4/04/2016 4/10/2016 Pixel Driver Design Completed 4/20/2016
5 4/11/2016 4/17/2016 PCB Design Completed 3/30/2016
6 4/18/2016 4/24/2016 Testing Text Display Completed 4/20/2016
7 4/25/2016 5/01/2016 UI Webserver Completed 4/25/2016
8 5/02/2016 5/08/2016 Final Testing and Debugging Completed 5/21/2016

Parts List & Cost

Sl. No Part Name Source of purchase Quantity Cost($)
1 Raspberry Pi 3 Adafruit 1 44.49
2 LED panels Preet 4 0
3 74HC245 Digikey 2 2
4 ATX PSU Amazon 1 20.94
5 Molex Connectors Amazon 4 15
6 PCB OSH Park 3 30
7 Aluminum Extrusion Adafruit 1 7.50
8 Oval T-Nut Adafruit 50 9.95
9 Power Adapter for Raspberry PI Amazon 1 9.99

Design & Implementation

Hardware Design

LED Panels Working

LED Panel Front

The display panels use multiplexing to draw picture information, which means that the rows and columns are updated fast than the human eye can process. If the updating speed is fast enough, eyes will see a complete picture without flickering. The updating process is as follows

  • Select the row to be updated.
  • Output the desired column data on selected row.
Row Selection

Row selection is done by using a 3-to-8 address decoder (74HC138D). There are three address inputs to the display marked A, B and C. Based on the truth table, only one input is active (low) at a time.

Truth Table
Row Configuration

Since the panels has 16 rows, the 3-to-8 address decoder select rows in parallel. For example, when the 1st row (Row1) is selected, it also selects the 9th row (Row9). Using this technique implies that we must supply data for the columns for two unique rows at a time.

Rows with same name are selected together

The outputs of the decoder is connected to a P-Channel MOSFET, because the decoder itself can only handle low currents and cannot drive a row of LEDs directly. The P-Channel MOSFET provides the high current needed to drive a row of LEDs.

Output Mosfets

The decoder outputs are shared between every 8 outputs (1 and 9, 2 and 10, repeating that pattern until row 8 and 16).

Column Selection

The column data is stored in a 16-bit serial-in, parallel-out shift register. Since the display is 32 pixels wide, two shift registers must be chained together. The shift register is designed to work with LEDs and implements a constant-current system that ensures the LED brightness remains uniform. The panels that we are using utilize SCT2026 shift registers. These are 16-bit Serial-In/Parallel-Out registers.


Shift register block diagram

There are 12 of these shift registers on the display. 3 each are used to hold the Red, Green, and Blue data for 1 of 4 quadrants of the display. (3 colors * 4 quadrants = 12 chips)


The 4 quadrants


For drawing 16 rows using the 8 outputs of the decoder, we must have unique data for each row pair. When Row 1 and Row 9 are selected, we must provide each row with unique data. This forces us to use two different shift registers for each row pair, an upper register and a lower register. Because of this, the display is divided into an upper half and a lower half. The data is shifted into the top half via the R1, G1 and B1 signals on the connector. The bottom half’s data is supplied by the R2, G2 and B2 signals on the connector. Then, since our display is 32 pixels wide, we must use 2 shift registers to hold all 32 bits of pixel data for a single row. This creates the left and right halves of the display. Each quadrant of the display is controlled by 3 shift registers, one for each color. First, Row 1 and Row 9 are selected. 32 bits of data are shifted into each color’s shift register (R1, G1, B1), and then latched. At the same time, 32 bits of data are also shifted into each color’s shift register for the bottom half (R2, G2, B2), and then latched. The process repeats 7 more times, each time incrementing which rows are selected, until every line has been updated.

Conceptual Schematic

In summary in order to display something on the LED panels the following steps needs to be performed by the driver

  • Shift the pixel data for row 0 into the top column drivers and the pixel data for row 16 into the bottom column drivers using the R1, G1, B1, R2, G2, and B2 data inputs and the SCLK shift clock signal.
  • Assert the blanking signal to blank the display.
  • Set the address input to 0.
  • Latch the contents of the column drivers‘ shift registers into the column drivers‘ output registers using the LATCH signal.
  • De-assert the blanking signal to display rows 0 and 16.
  • Wait some fixed amount of time.
  • Repeat the process for each of the pairs of rows in the display.
  • Repeat the entire process at least 100 to 200 times per second to prevent flicker.

Hardware Interface

The connector on the RGB panels is called a Hub75 interface. Each panel typically has two ports, one is the input and the other is the output to chain additional panels.

LED Panel Interface

PCB Design

The LED panels use 74HC245 line drivers, these transceivers require 5v logic levels whereas the SJONE board only supports 3.3v logic. In order to drive the LED panels from 3.3v GPIO pins of the SJONE board, level-shifting IC is used to level shift signals from 3.3V to 5V and shield the SJONE board GPIOs from overloading. For this purpose, and to make it easier to connect the panels to the SJONE board a PCB was designed in EAGLE. The PCB attaches to GPIO pins of SJONE board and provides easily accessible, level-shifted output for the LED panels. The PCB also breaks-out free pins so that they can be used for other purposes.

Schematic Design
PCB of Board
PCB of Board


PCB of Board

Software Design

Classes

The software for driving the LED panels is divided into two classes, GFX and RGB. The GFX class implements all the methods for drawing various characters on the LED panels, setting their heights, and colors. It does not concerns with how the LED panel works, and just assumes the LED panels to be a canvas to draw on. The GFX class has virtual functions, which deals with how to actually display something on he panels. These virtual functions are implemented in the RGB class, which inherits from GFX class.

Classes

Tasks

Further there are three tasks to get the LED panel running, and displaying the required task. The first task is setuppanel, which has a low priority. This task only runs once, and sets all the parameters like text size, wrap, etc. The second task called panel runs continuously, and has high priority because it is responsible for displaying the text and refreshing the LED panels. The third task is simply called gpioTask, it is a medium priority task, and is reponsible for receiving the text to display over UART from raspberry PI.

Tasks

Webpage

A webpage was designed hosted on Amazon AWS. The raspberry pi connects to the service provided by the webpage, any text entered on the website is transmitted to raspberry pi, which sends the received text over UART to the SJONE board to be displayed on the LED panels.

Login Page
Text Entry Page

Implementation

Fonts

The fonts displayed on the LED panels are implemented as an array of hexadecimal values, and in alphabetical order.


This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

PWM

The code tries to use a technique called Binary Code Modulation to control the colors of the display. Driving with Pulse Width Modulation (PWM) would turn the LED on for an amount of time proportional to the desired brightness, then turn it off for the rest of the period. BCM divides the period into binary-length segments (1x, 2x, 4x, etc), and turns the LED on or off for each of these segments according to the bits of the LED’s desired brightness. The pixel data must be divided up into bitplanes. These bitplanes are nothing but an array in which each element is a single bit from a color value in the displayed image. Each pixel would require three separate bitplanes, one for each color element. However to drive the display, all three colors are written out for two different pixels at the same time. The code stores six bits, one from each bitplane, together in a byte. This way the bytes are immediately ready to be written to the GPIO port during the interrupt. The code refers to the arrays of ready-to-write bytes as “planes,”. In each interrupt (RGB::updateDisplay) a byte from the appropriate plane is written out to the GPIO port and the delay until the next interrupt is set.

Bitplanes
 void refreshISR(void)
 {
   activePanel->updateDisplay();
 }
Flow

Messaging Protocol

MQTT (Message Queue Telemetry Transport) is the messaging protocol used for sending text from our webapp to the LED panels. MQTT is a light weight messaging protocol that uses publisher and subscriber architecture. Publishers are the devices that send data and subscribers are the ones that receive data. Devices that need to receive data must have MQTT client program such as Eclipse Paho running on them. Furthermore, the client program running on these devices need to subscribe to topics from which they want to receive data. The devices that need to send data also must have Paho MQTT client running on them. To send data, devices have to publish data to certain topics. There is another program that sits in between the sending and the receiving devices which is called an MQTT broker. The job of an MQTT broker is to receive data from senders and then send the data to receivers with appropriate topics.

The figure below shows our MQTT messaging protocol architecture. The architecture shows an eclipse Paho client program, running on AWS (Amazon Web Service), is publishing text on a topic called "my_text_topic". It also shows the Paho client program running on raspberry pi subscribing to the topic "my_text_topic". The MQTT broker known as Mosquitto running on AWS receives text from the publisher publishing on topic "my_text_topic" and sends the data to the receiver that has already subscribed to topic "my_text_topic".

MQTT Messaging Protocol Architecture

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

Issue #1: No Datasheets

The RGB LED panels we used did not have any datasheets available for them, this was worsened by the fact that they also did not have a standard interface to drive them like SPI or I2C. We decided to resolve this by studying the datasheets of the integrated circuits which were on the panels, but soon we bumped into another problem. The IC's were made by an obscure manufacturer called "CHIPONE".

Integrated Circuits on the Panel

Issue #1: Shapes and Graphics

We ended up getting datasheets from another manufacturer who made IC with similar functionality. In the end not all features were similar between the two manufacturers, but it did allow us to get the basic functionality working.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

http://bikerglen.com/projects/lighting/led-panel-1up/
http://www.batsocks.co.uk/readme/art_bcm_1.htm

Appendix

You can list the references you used.