Difference between revisions of "F18: Catch me if you can"

From Embedded Systems Learning Academy
Jump to: navigation, search
(Schedule)
(References)
 
(289 intermediate revisions by 2 users not shown)
Line 13: Line 13:
 
== Project Title ==
 
== Project Title ==
  
'''Catch Me If You Can'''
+
===Catch Me If You Can===
 +
[[File:Egg.jpg|600px|thumb|center|'''Catch me if you can''']]
  
 
== Abstract ==
 
== Abstract ==
 
"Catch me if you can" is a fun game where the user must be attentive and agile enough to  
 
"Catch me if you can" is a fun game where the user must be attentive and agile enough to  
catch the randomly dropping eggs from above into a basket. This is all displayed in the LED matrix acting as the screen. The user shall gain and accumulate points equivalent to the eggs collected successfully and there shall be a limited score for each level.
+
catch the randomly dropping eggs from above into a basket with increasing difficulty levels for an intriguing experience. This is all displayed in the LED matrix acting as the screen.
The system will consist of two SJ boards, the one board will be used as a game console with which user will try to catch the eggs by moving the board in the required orientation. The other board will control the display module that displays the graphics of eggs falling and also the basket movement. The display module shall communicate with  the game console via RF Nordic transceiver. There will be various sounds produced by the display module board for various events during the game like an egg catch\miss or an intermediate milestone reached.
+
The system will consist of two SJ1 boards, one used as a game console with which user will try to catch the eggs by moving it in the required orientation. The other board will control the display module that displays the graphics of eggs falling and also the basket movement. The display module shall communicate with  the game console via RF Nordic transceiver. There will be game sounds produced by the display module board for various events during the game like entering a new level.
  
 
== Objectives & Introduction ==
 
== Objectives & Introduction ==
Display Module:LED display
+
=== Objective ===
Control Module:/* yet to fill*/
+
To develop an Embedded system in the form of a 2D game involving a Matrix LED display acting as the Human Machine Interface
Wireless Module:/* yet to fill */
+
to guide the player along the way while playing the game. This project aims at integrating micro-controller peripheral drivers and the
 +
application software in a meaningful way, where the accelerometer data is sent out from a node via wireless Nordic transceiver
 +
to control slider movement on the other node to control the game according to player's performance.
 +
 
 +
=== Introduction ===
 +
 
 +
The Project consists of three main modules:
 +
 
 +
'''Console Module:''' It consists of accelerometer on SJ one board. Calibrated board orientation and switch pressed status is sent to the Display Module via Wireless Module.
 +
 
 +
'''Display Module:''' It is responsible for controlling  32*32 LED Matrix and Piezo buzzer interfaced to SJ One Board.
 +
 +
'''Wireless Module:''' This  establishes communication between Display and Console module.
 +
 
 +
==== About the game ====
 +
* Player should collect the eggs into the basket which are shot from the canon.
 +
* Press switch on the console (SJOne board) to start the game.
 +
* Tilt the console left or right to move the basket.
 +
* Collect the eggs falling of randomly.
 +
* Avoid red objects, if caught Game Over, else continue to collect eggs till the end of level.
 +
* 6 eggs need to be caught to progress to next level.
 +
* Yellow egg is a freebee where the basket expands to help the player.
 +
* Level 2 and 3 has rising water level on each egg miss which increases the difficulty of the game.
 +
* Player can play and pause the game anytime and resume from where he paused.
  
 
=== Team Members & Responsibilities ===
 
=== Team Members & Responsibilities ===
*  Aquib Abduljabbar Mulani
+
'''[https://www.linkedin.com/in/aquib-abduljabbar-mulani-198228115/ Aquib Abduljabbar Mulani]'''
** Wireless chip driver/application and calibrating accelerometer.   
+
** Wireless chip TX driver/application and calibrating accelerometer.   
*  Kailash Kumar Chakravarty
+
'''[https://www.linkedin.com/in/kailash-chakravarty-7b66b111/ Kailash Chakravarty]'''
** RGB LED 32x32 matrix driver and game display application code.
+
** RGB LED 32x32 matrix driver and game application code.
*  Nandini Mandya Shankaraiah
+
'''[https://www.linkedin.com/in/nandini-shankar-0462a247/ Nandini Mandya Shankaraiah]'''
** Audio output driver and game display application code.   
+
** Audio output and  Wireless chip RX driver/application.   
*  Rishabh Sheth
+
'''[https://www.linkedin.com/in/rishabh-sheth/ Rishabh Sheth]'''
** Managing WiKi, PCB design, and console application code.
+
** PCB design.
*  Swanand Sapre
+
'''[https://www.linkedin.com/in/swanandcse/ Swanand Sapre]'''
** Menu handling via switches and console application code.
+
** Console and Game design and application code.
  
 
== Schedule ==
 
== Schedule ==
Line 48: Line 72:
 
|-
 
|-
 
! scope="row"| 1
 
! scope="row"| 1
| 10/08/2018
+
| 10/16/2018
 
|  
 
|  
 
* Product Requirement Analysis & Order Required Parts.  
 
* Product Requirement Analysis & Order Required Parts.  
Line 55: Line 79:
 
| 10/25/2018
 
| 10/25/2018
 
|-
 
|-
! scope="row"| 3
+
! scope="row"| 2
 
| 10/30/2018
 
| 10/30/2018
 
|  
 
|  
Line 63: Line 87:
 
| 11/05/2018
 
| 11/05/2018
 
|-
 
|-
! scope="row"| 4
+
! scope="row"| 3
 
| 11/06/2018
 
| 11/06/2018
 
|
 
|
Line 72: Line 96:
 
| 11/13/2018
 
| 11/13/2018
 
|-
 
|-
! scope="row"| 5
+
! scope="row"| 4
 
| 11/13/2018
 
| 11/13/2018
 
|
 
|
* Develop algorithm for basket movement using accelerometer values
+
* Develop algorithm for basket movement and dropping eggs using accelerometer values
 
* Basic LED testing by activating individual and group of pixels
 
* Basic LED testing by activating individual and group of pixels
 
* Develop game specific APIs to draw objects like basket on top of led driver  
 
* Develop game specific APIs to draw objects like basket on top of led driver  
Line 82: Line 106:
 
| 11/16/2018
 
| 11/16/2018
 
|-
 
|-
! scope="row"| 6
+
! scope="row"| 5
 
| 11/20/2018
 
| 11/20/2018
 
|  
 
|  
Line 89: Line 113:
 
* Check Nordic Wireless Transmit part by sending accelerometer value
 
* Check Nordic Wireless Transmit part by sending accelerometer value
 
* Project report update on the wiki.
 
* Project report update on the wiki.
| In Progress
+
| Completed
|  
+
| 11/22/2018
 
|-
 
|-
! scope="row"| 7
+
! scope="row"| 6
 
| 11/27/2018
 
| 11/27/2018
 
|
 
|
Line 99: Line 123:
 
* Generating different tones using PWM on Piezo buzzer  
 
* Generating different tones using PWM on Piezo buzzer  
 
* Check Nordic wireless receive part  
 
* Check Nordic wireless receive part  
|
+
|Completed
|
+
|12/1/2018
 
|-
 
|-
! scope="row"| 8
+
! scope="row"| 7
 
| 11/30/2018
 
| 11/30/2018
 
|  
 
|  
 
* Integrating calibrated accelerometer, switch functionalities and wireless transfer on console board
 
* Integrating calibrated accelerometer, switch functionalities and wireless transfer on console board
 
* Once Integrated check the LED display response to the varying inputs from the game console
 
* Once Integrated check the LED display response to the varying inputs from the game console
|  
+
|Completed
|
+
| 12/06/2018
 
|-
 
|-
! scope="row"| 9
+
! scope="row"| 8
 
| 12/04/2018
 
| 12/04/2018
|
 
* Final testing and Bug fixes
 
|
 
 
|
 
|
 +
* Display the score of the user upon request
 +
* Final testing product with varying inputs of gaming console|
 +
|Completed
 +
| 12/11/2018
 
|-
 
|-
! scope="row"| 10
+
! scope="row"| 9
 
| 12/11/2018
 
| 12/11/2018
 
|  
 
|  
 
* Complete Wiki Report and Final Demo  
 
* Complete Wiki Report and Final Demo  
|
+
|Completed
|
+
| 12/18/2018
 
|}
 
|}
  
Line 180: Line 205:
 
! scope="row"| 8
 
! scope="row"| 8
 
| BOM / PCB components   
 
| BOM / PCB components   
| [https://www.sparkfun.com Sparkfun]
+
| [https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=320630c400 Moser]
 
| -
 
| -
 
| $20
 
| $20
Line 187: Line 212:
 
== Design & Implementation ==
 
== Design & Implementation ==
  
=== Hardware Design ===
+
=== Hardware and PCB Design ===
Discuss your hardware design hereShow detailed schematics, and the interface here.
+
 
 +
=== PCB Design ===
 +
PCB is an important part of the embedded system, it is certainly true for this project as it reduced wire complexity and gave independent power to our circuit. There are many softwares available for PCB design, among them Eagle and KiCAD are more popular and both software are free for  students. We chose KiCAD (v5.10.0) for PCB design over Eagle because, it is opensource so we din't have to worry about the license. The second reason was that, all of our team members was new to PCB design so the learning curve was same for both software but we found a good tutorial series for KiCAD on youtube ( [https://www.youtube.com/playlist?list=PLEBQazB0HUyR24ckSZ5u05TZHV9khgA1O KiCAD tutorials] ). KiCAD has its own issues which are discussed in the issue section of this wiki.
 +
The steps involved in the PCB design process are described in the next section.
 +
<BR/>
 +
 
 +
==== Schematic Design: ====
 +
 
 +
Our project can be divided into two main circuits, first is game display circuit and second is a console circuit. We decided to design separate PCB for both circuits as doing so can make wiring easy and improve the user experience.   
 +
 
 +
===== Display PCB schematic: =====
 +
[[File:PCB Schematic 1 Game Display.png|700px|thumb|center|'''Game Display PCB Schematic''']]
 +
<BR/>
 +
 
 +
Display PCB has two independent circuits. One circuit is to connect SJOne board to LED panel connector and with two piezo buzzers. While another circuit is to connect one unused power cable of LED panel to SJOne board so that we don't have to power SJOne board from PC while we are playing the game. Our preliminary idea was to make this PCB, a Arduino kind of shield but for SJOne board. 
 +
 
 +
===== Console PCB schematic: =====
 +
[[File:PCB Schematic 2 Game Console.png|700px|thumb|center|'''Game Console PCB Schematic''']]
 +
<BR/>
 +
In this game, console is used to move the basket to catch fast falling eggs and if there were any wires attached to console then it is very inconvenient for the user to play. so, we decided to make PCB which can charge battery and power the console while the user is playing. As shown in figure, the heart of the circuit is microchip's MCP73831 LiPo battery charging management IC. One LED is connected to it's Status Pin which glows when the battery is charging. A mini USB B port is used to connect to power resource (PC or any 5V mobile charger)via USB cable to charge the battery. while playing the game, the user must connect USB A port to SJOne Board's mini USB B port. To use the console on battery power user must turn on/off switch.
 +
 
 +
==== PCB Layout: ====
 +
 
 +
After schematic design, the most important step is to connect the PCB layout. In KiCAD components is not automatically associated with it's PCB footprint, so it's user's responsibility to connect right PCB footprint with the right components. In our case, we did not have the footprint of JLC connector and Rocker switch. so, we created it in a different window and saved it. The amazing feature of KiCAD is once we have done with PCB layout we can visualize PCB in 3D by pressing just one button. Below are actual screenshots of both, PCB layout & their 3D model.
 +
 
 +
===== Display PCB layout: =====
 +
<center>
 +
<table>
 +
<tr>
 +
<td>
 +
[[File:Dispay PCB layout without CU.png|300px|thumb|center|'''Dispay PCB layout without Copper layer''']]
 +
</td>
 +
<td>
 +
[[File:Display PCB layout.png|300px|thumb|center|'''Display PCB layout with Copper layer''']]
 +
</td>
 +
<td>
 +
[[File:Display PCB front 3D view.png|300px|thumb|center|'''Display PCB front 3D view''']]
 +
</td>
 +
<td>
 +
</tr>
 +
</table>
 +
</center>
 +
 
 +
 
 +
 
 +
===== Console PCB layout: =====
 +
 
 +
<center>
 +
<table>
 +
<tr>
 +
<td>
 +
[[File:Console PCB layout without CU.png|250px|thumb|center|'''Console PCB layout without Copper layer''']]
 +
</td>
 +
<td>
 +
[[File:Console PCB layout.png|264px|thumb|center|'''Console PCB layout with Copper layer''']]
 +
</td>
 +
<td>
 +
[[File:Console PCB front 3D view.png|300px|thumb|center|'''Console PCB front 3D view''']]
 +
</td>
 +
<td>
 +
</tr>
 +
</table>
 +
</center>
 +
 
 +
==== PCB manufacturing and soldering: ====
 +
 
 +
We chose JLC PCB to manufacture our PCB because, it is the cheapest and convenient option available for any prototype PCB manufacturing. It just cost us $2 for quantity of 10 PCB and $17 for shipment. We received manufactured PCB in just 5 days. We order components from Moser the total BOM cost of both PCB is approx $25 including shipment. Followings are actual photos of manufactured & assembled PCBs.
 +
 
 +
<center>
 +
<table>
 +
<tr>
 +
<td>
 +
[[File:Console Actual.jpg|300px|thumb|center|'''Actual Console PCB''']]
 +
</td>
 +
<td>
 +
[[File:Actual Display PCB.jpeg|260px|thumb|center|'''Actual Display PCB''']]
 +
</td>
 +
<td>
 +
</tr>
 +
</table>
 +
</center>
  
 
=== Hardware Interface ===
 
=== Hardware Interface ===
In this section, you can describe how your hardware communicates, such as which BUSes used.  You can discuss your driver implementation here, such that the '''Software Design''' section is isolated to talk about high level workings rather than inner working of your project.
 
  
=== Software Design ===
+
[[File:Hardwareinterface.PNG|570px|thumb|center|'''Hardware Design Diagram''']]
Tasks within LPC Board 1 (LED display):<br />''Input_handler'' : This task takes the Accelerometer values as inputs from other LPC board and determines the exact corresponding position of the basket.<br />''Display_handler:'' This task is responsible for displaying the contents into the LED matrix display at a certain rate.<br />Note: Actual screen refreshing takes place at a much higher rate.<br />Tasks within LPC Board 2 (Console):<br />  
+
 
''Data_sender :'' This task continuously sends the raw accelerometer values to LPC board 1.<br />''Game_handler :'' This task is responsible for handling events like game start, game pause, game end via on board switches.
+
 
 +
 
 +
Hardware design diagram above gives an overview of the entire system which consists of the two SJ-One controllers: one board is used as Control Module and other board is used as the Display Module.
 +
 
 +
*The Console Module uses the onboard accelerometer on SJ-One which is interfaced via I2C protocol. The calibrated accelerometer values are then used to determine the basket position on the LED Matrix.
 +
 
 +
*The Display Module SJ-One board is used to control a 32*32 RGB LED Matrix.This matrix displays the basket, eggs shot from the cannon.The movement of the basket is as per the orientation value received from the Control Module, through Wireless Module. It also consists of Peizo buzzer which is controlled via PWM pin.
 +
 
 +
=== Software Design and Implementation ===
 +
 
 +
==== Display Module ====
 +
 
 +
'''RGB LED Matrix:'''
 +
<center>
 +
<table>
 +
<tr>
 +
<td>
 +
[[File:RGB_LED.PNG|400px|thumb|center|'''RGB LED matrix display''']]
 +
</td>
 +
<td>
 +
[[File:RGB32_32.jpg|400px|thumb|center|'''RGB Display'''']]
 +
</td>
 +
<td>
 +
</tr>
 +
</table>
 +
</center>
 +
 
 +
The Human Machine Interface is a display which is composed of 6mm pitch 1024 RGB LEDs arranged in a 32x32 matrix. 32 rows of the matrix is divided into 16 interleaved sections. Here the first section is the 1st and 16th 'row' (32 x 2 = 64 RGB LEDs), the second section is 2nd and 17th 'row' and so on. On the PCB is 12 LED driver chips. These are like 74HC595s but they have 16 outputs and they are constant current. 16 outputs * 12 chips = 192 LEDs that can be controlled at once, and 64 * 3 (R G and B) = 192. So now the design comes together. We can have 192 outputs that can control one line at a time, with each of 192 R, G and B LEDs either on or off. The LPC1758 controller selects which section to currently draw (using A, B, C and D address pins - 4 bits can have 16 values). Once the address is set, the controller clocks out 192 bits of data (24 bytes) and latches it. Then it increments the address and clocks out another 192 bits, etc until it gets to address #15, then it sets the address back to #0. To light up an individual pixel, appropriate row value is loaded on to the address pins A,B,C & D, Clock is set out to traverse the row and when required pixel is reached, the latch is set high to turn ON the LED.
 +
The hardware interface to the LED Matrix uses GPIO for all data and control lines. A GPIO clock is toggled to shift in data sitting at the Matrix's 6 data ports.
 +
 
 +
{| class="wikitable"
 +
! SJ One Board Pin
 +
! Name
 +
! Description
 +
|-
 +
| P0.0
 +
| addrA
 +
| Address Input A
 +
|-
 +
| P0.1
 +
| addrB
 +
| Address Input B
 +
|-
 +
| P2.6
 +
| addrC
 +
| Address Input C
 +
|-
 +
| P2.7
 +
| addrD
 +
| Address Input D
 +
|-
 +
| P1.29
 +
| Latch
 +
| Shift in row data/Active High
 +
|-
 +
| P1.28
 +
| Output Enable
 +
| Turn on selected rows/Active Low
 +
|-
 +
| P1.19
 +
| Clock
 +
| Shift clock
 +
|-
 +
| P1.22
 +
| R1
 +
| Top half red data
 +
|-
 +
| P0.26
 +
| G1
 +
| Top half green data
 +
|-
 +
| P1.23
 +
| B1
 +
| Top half blue data
 +
|-
 +
| P1.30
 +
| R2
 +
| Bottom half red data
 +
|-
 +
| P1.31
 +
| G2
 +
| Bottom half green data
 +
|-
 +
| P2.5
 +
| B2
 +
| Bottom half blue data
 +
|}
 +
 
 +
'''Piezo Buzzer:'''
 +
[[File:Piezo_2019_fall.JPG|200px|thumb|right|'''Piezo Schematic Diagram''']]
 +
[[File:Piezo buzzer 2019 fall.jpg|150px|thumb|center|'''Piezo Physical Diagram''']]
 +
Piezo electric buzzer are high performance buzzer that employ piezoelectric elements and are designed for easy incorporation into various circuits. These buzzers are designed for external excitation, the same part can serve as both a musical tone oscillator and a buzzer. In our project we are using this device to create musical tones by varying the operating frequency.The different range of operating frequency
 +
are generated from PWM peripheral. Different range of frequencies are maintained as constants ,these constants are fed to PWM,which generates square wave. The output of the PWM is driving the Piezo buzzer.
 +
 
 +
''' Code snippet for creating musical tones by varying frequency: '''
 +
<syntaxhighlight lang="c">
 +
int fire[]=
 +
{
 +
550,/*twice the freq of this and use always tempo as 40 */
 +
404,
 +
315,
 +
494,
 +
182,
 +
260,
 +
455,
 +
387,
 +
340
 +
};
 +
 
 +
void fire_sound_level(void){
 +
for(int i = 0;i < 8;i++)
 +
{
 +
uint8_t tempo = 40;
 +
while(tempo)
 +
{
 +
pwm.SetFrequency(fire[i]*2);
 +
pwm.SetDutyCycle(pwm.k2_1,50);
 +
pwm.PwmEnableMode(true);
 +
tempo--;
 +
}
 +
}
 +
pwm.PwmEnableMode(false);
 +
}
 +
</syntaxhighlight>
 +
 
 +
==== Control Module ====
 +
 
 +
'''Accelerometer:'''
 +
 
 +
[[File:CmpE244_S18_Detectable_Accelerations.png|400px|thumb|center|Accelerometer Detection]]
 +
 
 +
{|The SJ one board has an Accelerometer which is interfaced to the board using the I2C bus protocol.
 +
The MMA8452Q which is a smart low-power, three-axis, capacitive micromachined accelerometer with 12 bits of resolution is used in our project.
 +
Accelerometers are electromechanical devices that are used to sense acceleration that can be of various forms, for instance gravity.
 +
|In our project,we have calibrated the accelerometer based on the values of X,Y and Z co-ordinates corresponding to different orientations of the accelerometer to control the horizontal movement of the Basket int the game to catch the eggs on the screen. This has also helped us decide and control the speed of the basket. As shown in the code snippet below the x movement on the right is determined based on the x co-ordinate and the console sensitivity which you wish to set.Similarly movement on the left can also be calculated for further use.
 +
|}
  
=== Implementation ===
+
''' Code snippet for Accelerometer Calibration: '''
This section includes implementation, but again, not the details, just the high levelFor example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI FlashYou can include sub-sections for each of your component implementation.
+
 
 +
<syntaxhighlight lang="c">
 +
 
 +
if (((x_coordiante > px_coordiante + CONSOLE_SENSITIVITY) && (x_coordiante <= CONSOLE_TILT_RANGE) ))
 +
{
 +
        boardOrientation=left;
 +
        bskObj.speed=BASKET_SPEED;
 +
        px_coordiante=x_coordiante;
 +
}
 +
    //left
 +
    else if((x_coordiante<px_coordiante-CONSOLE_SENSITIVITY && x_coordiante>=-CONSOLE_TILT_RANGE))
 +
{
 +
        boardOrientation=right;
 +
        bskObj.speed=BASKET_SPEED;
 +
        px_coordiante=x_coordiante;
 +
}
 +
else if(x_coordiante>CONSOLE_TILT_RANGE ){
 +
        boardOrientation=left;
 +
        bskObj.speed=BASKET_SPEED;
 +
}
 +
else if(x_coordiante<-CONSOLE_TILT_RANGE ){
 +
        boardOrientation=right;
 +
        bskObj.speed=BASKET_SPEED;
 +
    }
 +
else
 +
{
 +
        boardOrientation=invalid;
 +
        py_coordiante=y_coordiante;
 +
}
 +
 
 +
</syntaxhighlight>
 +
''' Wireless Module: '''
 +
[[File:nordic.PNG|350px|thumb|center|'''Nordic Wireless Block Diagram''']]
 +
 
 +
{|The on-chip Nordic nRF24L01+ is interfaced to the SJone board using Serial Peripheral Interface(SPI) bus protocol.
 +
The nRF24L01+ is a single chip 2.4GHz transceiver with an embedded baseband protocol engine, suitable for ultra low power wireless applications. The nRF24L01+ is designed for operation in the world wide ISM frequency band at 2.400 - 2.4835GHz.The nRF24L01+ supports an air data rate of 250  kbps, 1 Mbps and 2Mbps. The high air data rate combined with two
 +
power saving modes make the nRF24L01+ very suitable for ultra low power designs.
 +
The register map, which is accessible through the SPI, contains all configuration registers in
 +
the nRF24L01+ and is accessible in all operation modes of the chip.
 +
The embedded baseband protocol is based on packet communication and supports various modes from manual operation to advanced autonomous protocol operation. Internal
 +
FIFOs ensure a smooth data flow between the radio front end and the system’s MCU. Enhanced ShockBurst reduces system cost by handling all the high speed link layer operations.
 +
Whenever a data is to be transferred over the Nordic Wireless transceiver,a packet containing the required data is made and then transmitted using ''wireless_send()'' function to the address of the receiver node. On the other hand, the receiver node waits for the package to be received and once it receives the packet, the data in the the form of X,Y and Z co-ordinates is extracted from the packet and then used to vary the basket position on the display module side. The code snippet below show basic implementation of the Wireless Transmitter and the Wireless Receiver tasks using the Nordic wireless transceiver.
 +
 
 +
|''' Code snippet for Wireless Transmitter: '''
 +
 
 +
<syntaxhighlight lang="c">
 +
 
 +
struct pckt
 +
{
 +
    int16_t x;
 +
    int16_t y;
 +
    int16_t z;
 +
    int16_t buttonPressed=0;
 +
};
 +
void WirelessTx(void *p)
 +
{
 +
      while(1)
 +
      {
 +
          pckt var;
 +
          var.x = AS.getX();/values from accelerometer*/
 +
          var.y = AS.getY();
 +
          var.z = AS.getZ();
 +
          pckt var;
 +
            while(1)
 +
            {
 +
                if(SW.getSwitch(1))
 +
                {
 +
                    var.buttonPressed=1;
 +
                    vTaskDelay(300);
 +
                }
 +
                else if(SW.getSwitch(2))
 +
                {
 +
                    var.buttonPressed=2;
 +
                    vTaskDelay(300);
 +
                }
 +
          wireless_send(REM, mesh_pkt_nack,(pckt*)&var, 8, 0);
 +
          vTaskDelay(50);
 +
            }
 +
      }
 +
}
 +
</syntaxhighlight>
 +
 
 +
''' Code snippet for Wireless Receiver: '''
 +
 
 +
<syntaxhighlight lang="c">
 +
 
 +
void wirelessRx(void* p)
 +
{
 +
    while(1)
 +
    {
 +
        mesh_packet_t rcvPkt;
 +
        int timeout_ms = 50;
 +
 
 +
        if(wireless_get_rx_pkt(&rcvPkt, timeout_ms)){
 +
 
 +
            iphObj.x_coordiante = (int16_t)(*((uint16_t*)(rcvPkt.data+0)));
 +
            iphObj.y_coordiante = (int16_t)(*((uint16_t*)(rcvPkt.data+2)));
 +
            iphObj.z_coordiante = (int16_t)(*((uint16_t*)(rcvPkt.data+4)));
 +
            iphObj.buttonPressed= (int16_t)(*((uint16_t*)(rcvPkt.data+6)));
 +
            if(iphObj.buttonPressed==1 )
 +
            {
 +
                xSemaphoreGive(playPauseHandler);
 +
            }
 +
            else if(iphObj.buttonPressed==2 )
 +
            {
 +
              xSemaphoreGive(resetGameHandler);
 +
            }
 +
        }
 +
        vTaskDelay(50);
 +
    }
 +
}
 +
</syntaxhighlight>
 +
 
 +
 
 +
==== Tasks and Flow Control ====
 +
 
 +
<center>
 +
<table>
 +
<tr>
 +
<td>
 +
[[File:Tasks list 2019 fall.JPG|185px|thumb|center|'''List of Free RTOS Tasks''']]
 +
</td>
 +
<td>
 +
[[File:Input handler 2019 fall.JPG|300px|thumb|center|'''Input Handler Class''']]
 +
</td>
 +
<td>
 +
</tr>
 +
</table>
 +
</center>
 +
 
 +
 
 +
<center>
 +
<table>
 +
<tr>
 +
<td>
 +
[[File:Display_handler_2019_spring.JPG|300px|thumb|center|'''Display Handler Class''']]
 +
</td>
 +
<td>
 +
[[File:Logic handler 2019 fall.JPG|315px|thumb|center|'''Game Logic Handler Class''']]
 +
</td>
 +
<td>
 +
</tr>
 +
</table>
 +
</center>
 +
 
 +
 
 +
''' Software Design in Display module:'''
 +
 
 +
''''Input_handler:''''  This is class, which contains all the functions which controls the position of the basket. Which is in turn depends on the console unit orientation value received from wireless task. This task also receives status of button press from the console unit. The values are received as a structure. Wireless task checks for button press and accordingly changes the state of game.i.e for button 1 press it pauses the game and for button 2 press it restarts the game. The accelerometer values are used to calibrate the basket horizontal movement.Depending upon the x-axis values of console the basket slides horizontally.
 +
 
 +
'''Display_handler:''' We have implemented the various functions to display the components used in our Game. It uses GFX matrix library to draw the shapes and pixel. Objects used in our game includes Baskets,Eggs,Cannon and Water. Apart form Object display Handler also has functions to implement the screens used in our Game like-Play/Pause screen,Game Over Screen,Win Screen.
 +
 
 +
'''Game_Begin:''' This is a task which divided into Logic Handler, Input Handler and Display Handler. Input Handler read the input,Logic Handler implements various algorithms to generate eggs with random behavior,checks for game Over condition,sliding the basket depending upon the direction received from Input handler,speed of sliding ,Logic to determine the catch or miss of Egg and increment the water level on every miss.Display Handler deals with displaying objects on screen. Each handler class have its manager functions which calls all the private functions of respective handler. From the game Task we call these manager functions of all the handlers.Basic Game theory is to check the input,update the logic and display. we are implementing same thing using handlers for display,logic and input.
 +
 
 +
[[File:Display Screen 2019 fall.JPG|500px|thumb|center|'''Display module screen state flow''']]
 +
 
 +
'''Tasks in Console Module :'''
 +
 
 +
'''Transmitter Task:''' This task periodically transmits the orientation values and button press status to the display module.
 +
Task Priority :1 (could be anything as it the only task running in the console).
  
 
== Testing & Technical Challenges ==
 
== Testing & Technical Challenges ==
Describe the challenges of your project.  What advise would you give yourself or someone else if your project can be started from scratch again?
 
Make a smooth transition to testing section and described what it took to test your project.
 
  
Include sub-sections that list out a problem and solution, such as:
+
===Issues, Challenges and solutions to get past them===
 +
 
 +
'''1.  RGB LED Matrix Display driver'''
 +
 
 +
Porting Adafruit LED driver, which is AVR microcontroller compatible into LPC was challenging because the library was not compatible with LPC1758 micro-controller. As a result, initially all the LEDs were getting turned on. Plenty of changes were done in the existing Adafruit library after which the driver was working as expected. Some of the changes were - to map the LPC GPIOs to LED matrix pins. This was challenging because choosing the pins also mattered for PCB design, which we were unaware until we started to design PCB. We had to remap the LPC GPIO pins to LED matrix as per PCB wiring convenience again. In addition to the basic API functions available, we had to develop many new APIs which were specific to the game using the bitmap to create various re-usable objects. So basically we had to migrate the whole library from AVR to LPC1758.
 +
 
 +
'''2.  Nordic Wireless'''
 +
 
 +
In Nordic Wireless, the transmitted data was received only once, despite the transmitter transmitting data continuously. This was because vTaskStartScheduler() API was used by us.The scheduler_start() API was the right API to be used for Nordic Wireless to function properly.
 +
Once we implemented the queue to collect orientation and switch status, we saw a delay in data reception. This was due to usage of scheduler_start() which initializes the wireless_service task.
 +
 
 +
'''3.  Peizo Buzzer'''
 +
 
 +
Determining the range of audio frequencies which would be audible and sensible was challenging.After days of trail and error method we found the range. After finding the range, the problem we encountered was with switching frequencies. Drastically varying frequency of PWM  will cause sound produced by Peizo unpleasant.In order to overcome this we had to vary frequency in small steps. Say you want to change frequency from 410 to 510. do it in steps 410,420,430 soon.One more important thing to verify is the whether the frequency generated by PWM peripheral matches your expected frequency, do verify it with logic analyzer once before writing the music tone libraries.
 +
 
 +
'''4.  Playing tone at all stages of the Game'''
 +
 
 +
Display of the objects being delayed, when different tones were played in the back ground. We did not understand what was causing this issue. Due to time constraints we could not further debug more on this. To overcome this would be challenge to us in the near future.
 +
 
 +
'''5.  PCB issue'''
 +
 
 +
For some of the components, KiCAD library was not present so we have to develop our own components and footprint library. One such components was Rocker Switch in display PCB. Designing footprint for this component was really hard as the manufacturer did not give clear measurement/dimensions for the footprint. When we received the components, legs of the switch was slightly thicker than described in datasheet. To overcome this we had to file metal legs in order to fit the switch in PCB.
 +
 
 +
Our PCB is of 1.6mm thickness while our USB Mini B connector was designed to fit into 1.5mm thick PCB. This made soldering the connector tedious.
 +
 
 +
SMD IC component in our console PCB which was very difficult to solder by hand. During soldering, we accidentally shorted some pins due to which our console PCB got burnt and we had to re-order the components again.       
 +
 
 +
'''6.  Task Priority'''
 +
 
 +
First thing is configuring task priorities and state machine for game state was challenging. We have a total of five tasks. To decide the priority of each task was time consuming, as we dint want the tasks to interfere with the game task which is of lower priority.To over come this we measured the game task execution time and used this time as a block period for higher priority tasks.
 +
 
 +
Another issue was that the game slowed down as the game level progressed. After debugging, we found out that the issue was due to high RIT_Interrupt rate. The RIT interrupt was very frequent, as a result more of the CPU time was consumed in context switching to interrupt, which slowed down the other tasks. To over come this we reduced interrupt rate by a factor  of 20 ,with which the issue was resolved without affecting the LED display refresh rate.
 +
 
 +
=== PCB module Testing ===
 +
We tested LED display with SJOne board using breadboard connection to make sure that there should not be any connection issue in final PCB design. Ones we received our PCB first tested PCB's continuity to make sure that all connections and traces are as expected. Also after soldering components, we did the continuity testing.
 +
 
 +
[[File: Battery testing.JPEG|250px|thumb|center|'''Battery charing discharging testing''']]
  
=== <Bug/issue name> ===
+
Console circuit testing was not possible before we design and received PCBs as we don't have main IC and it is available only in SMD. Ones we solder the whole PCB and gave power PCB got burnt, after rigorous testing and debugging we found that we used SPDT switch which connects battery's positive terminal to ground. We solve this problem in next iteration by not connection one lag of SPDT switch after that it worked fine. We configured our IC to charge 400 mAh battery at the rate of 80mAh (preferred configuration in the datasheet). So It takes approx 5h to charge battery ones it fully discharged.  We tested our circuit with two full charging-discharging cycles and everything worked as expected.
Discuss the issue and resolution.
+
<BR/>
 +
 
 +
=== Display Module and Game Testing ===
 +
 
 +
==== Steps of Testing  ====
 +
 
 +
1) The RGB LED Display was tested for basic objects like rectangle, line, characters. The flickering of the screen was observed initially
 +
with a slow screen refresh rate of anything slower than 5khz. So the refresh rate was fixed at 5khz. Below are snapshots of some of the
 +
screens tested.
 +
 
 +
2) Wireless module was tested by sending a single byte of data. Every time the byte was transmitted, we printed the transmitted value on the Hyperload terminal. Similarly at the receiving SJ one board, we printed the received value. Once this was achieved ,then we reapeted the same procedure with the actual data packet.This whole procedure ensured that the console module is working fine.
 +
 
 +
3) Once, we had the console module ready, we started integrating  the display module and console module. Once we integrated ,we checked for the basket movement while changing the board orientation. Until we had the smooth movement of the basket object on the screen, we continued to finely tune the calibration for accelerometer values.
 +
 
 +
4) After fine tuning the calibrations, we moved on to test out game algorithms, where the display screen was rigorously tested by playing the game continuously, reversing the console board and trying to see whether display responds. All the stages of game algorithms (the handlers mentioned the software design )  the start screen,end screen, count down screen  and display during game was verified.
 +
 
 +
5) The game algorithm i.e. system testing was done where we tested the screen navigation sequence, difficulty levels of the game (it
 +
should not be too easy to win and not too hard to win either). Also every member was asked to play the game for a through testing for robustness of the algorithm. Negative test cases were also tested like pressing the key randomly and likewise.
 +
 
 +
 
 +
{|
 +
|[[File:Basic objects.jpg|220px|thumb|right|'''Basic objects Testing''']]
 +
|[[File:321.gif|220px|thumb|right|'''Count down''']]
 +
|[[File:slideegg.gif|160px|thumb|'''Slider Movement Testing''']]
 +
|[[File:gameovertobesubmitted.JPEG|250px|thumb|right|'''Game End Screeen''']]
 +
|}
  
 
== Conclusion ==
 
== Conclusion ==
Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?
+
 
 +
At the start, project was a jigsaw puzzle. We only had pieces of knowledge and unaware of how to tailor it to solve the puzzle.
 +
Well we are successful in implementing our idea of building a game. This project has helped us to gain practical exposure in building a real time embedded system. This project gave us a platform to utilize all LPC drivers and Free RTOS knowledge which we learnt in our course work and what are the key things to consider while building a real time system. We are thankful to Preet, who motivated and guided us through out the course work.
  
 
=== Project Video ===
 
=== Project Video ===
Upload a video of your project and post the link here.
+
* [https://youtu.be/brXWSHTGY-g Motion based game catch me if you can]
  
=== Project Source Code ===
+
=== Project Code ===
[https://sourceforge.net/projects/sjsu/files/CmpE_S2016/ Sourceforge Source Code Link]
+
GitHub Link : [https://github.com/rishabh00/Catch_Me_If_You_Can Catch_Me_If_You_Can]
  
 
== References ==
 
== References ==
 
=== Acknowledgement ===
 
=== Acknowledgement ===
Any acknowledgement that you may wish to provide can be included here.
+
We would like to thank our Professor Preetpal Kang for all his awesome lectures and explanations of the embedded system topics, they could not have been explained any better than this! Not only did we enjoy working on this project but it also gave us an overall learning experience and precious life lessons. We would also like to thank the ISA members for always being around and ready for helping whenever required.
  
 
=== References Used ===
 
=== References Used ===
List any references used in project.
+
 
 +
[1] [https://www.sparkfun.com/datasheets/Components/SMD/nRF24L01Pluss_Preliminary_Product_Specification_v1_0.pdf Nordic wireless datasheet]
 +
 
 +
[2] [https://www.instructables.com/id/Creating-arcade-game-sounds-on-a-microcontroller/]
 +
 
 +
[3] [http://socialledge.com/sjsu/index.php/Low_Powered_Mesh_Network_stack Low_Powered_Mesh_Network_stack ]
 +
 
 +
[4] [https://www.youtube.com/playlist?list=PLEBQazB0HUyR24ckSZ5u05TZHV9khgA1O KiCAD tutorials for PCB]
 +
 
 +
[5] [https://learn.sparkfun.com/tutorials/rgb-panel-hookup-guide?_ga=2.65248494.1993636224.1545283057-617364471.1535821258]
  
 
=== Appendix ===
 
=== Appendix ===
 
You can list the references you used.
 
You can list the references you used.

Latest revision as of 17:53, 18 December 2019

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Project Title

Catch Me If You Can

Catch me if you can

Abstract

"Catch me if you can" is a fun game where the user must be attentive and agile enough to catch the randomly dropping eggs from above into a basket with increasing difficulty levels for an intriguing experience. This is all displayed in the LED matrix acting as the screen. The system will consist of two SJ1 boards, one used as a game console with which user will try to catch the eggs by moving it in the required orientation. The other board will control the display module that displays the graphics of eggs falling and also the basket movement. The display module shall communicate with the game console via RF Nordic transceiver. There will be game sounds produced by the display module board for various events during the game like entering a new level.

Objectives & Introduction

Objective

To develop an Embedded system in the form of a 2D game involving a Matrix LED display acting as the Human Machine Interface to guide the player along the way while playing the game. This project aims at integrating micro-controller peripheral drivers and the application software in a meaningful way, where the accelerometer data is sent out from a node via wireless Nordic transceiver to control slider movement on the other node to control the game according to player's performance.

Introduction

The Project consists of three main modules:

Console Module: It consists of accelerometer on SJ one board. Calibrated board orientation and switch pressed status is sent to the Display Module via Wireless Module.

Display Module: It is responsible for controlling 32*32 LED Matrix and Piezo buzzer interfaced to SJ One Board.

Wireless Module: This establishes communication between Display and Console module.

About the game

  • Player should collect the eggs into the basket which are shot from the canon.
  • Press switch on the console (SJOne board) to start the game.
  • Tilt the console left or right to move the basket.
  • Collect the eggs falling of randomly.
  • Avoid red objects, if caught Game Over, else continue to collect eggs till the end of level.
  • 6 eggs need to be caught to progress to next level.
  • Yellow egg is a freebee where the basket expands to help the player.
  • Level 2 and 3 has rising water level on each egg miss which increases the difficulty of the game.
  • Player can play and pause the game anytime and resume from where he paused.

Team Members & Responsibilities

Schedule

Week# Date Task Status Actual Completion Date
1 10/16/2018
  • Product Requirement Analysis & Order Required Parts.
  • Software Design and ownership of each module
Completed 10/25/2018
2 10/30/2018
  • Calibrating Accelerometer values for actual orientation
  • Project report update on the wiki.
Completed 11/05/2018
3 11/06/2018
  • Design schematics for console charging circuit & LED display circuit
  • Finalize parts and components for PCB design and develop footprints library for KiCAD (if not present)
  • Porting Adafruit LED driver into LPC
Completed 11/13/2018
4 11/13/2018
  • Develop algorithm for basket movement and dropping eggs using accelerometer values
  • Basic LED testing by activating individual and group of pixels
  • Develop game specific APIs to draw objects like basket on top of led driver
  • Project report update on the wiki.
Completed 11/16/2018
5 11/20/2018
  • Piezo Buzzer operation with different frequency
  • Order PCB for manufacturing and order missing components
  • Check Nordic Wireless Transmit part by sending accelerometer value
  • Project report update on the wiki.
Completed 11/22/2018
6 11/27/2018
  • Design PCB for Console & Display and generate Gerber files, finalize PCB manufacture
  • Start and Stop switch, which controls the power to the system and displays Welcome and Good Bye screen
  • Generating different tones using PWM on Piezo buzzer
  • Check Nordic wireless receive part
Completed 12/1/2018
7 11/30/2018
  • Integrating calibrated accelerometer, switch functionalities and wireless transfer on console board
  • Once Integrated check the LED display response to the varying inputs from the game console
Completed 12/06/2018
8 12/04/2018
  • Display the score of the user upon request
  • Final testing product with varying inputs of gaming console|
Completed 12/11/2018
9 12/11/2018
  • Complete Wiki Report and Final Demo
Completed 12/18/2018

Parts List & Cost

Sl No Parts Seller Quantity Price
1 SJOne LPC1758 Microcontroller Board Preetpal Kang 2 $160
2 RGB LED Matrix Panel - 32x32 Sparkfun 1 $55.6
3 Piezo Buzzer Amazon 2 $1.5
4 Accelerometer On board 1 NA
5 Switches On board 4 NA
6 Portable Power Supply Local seller 1 $5
7 RF Nordic On board 1 NA
8 BOM / PCB components Moser - $20

Design & Implementation

Hardware and PCB Design

PCB Design

PCB is an important part of the embedded system, it is certainly true for this project as it reduced wire complexity and gave independent power to our circuit. There are many softwares available for PCB design, among them Eagle and KiCAD are more popular and both software are free for students. We chose KiCAD (v5.10.0) for PCB design over Eagle because, it is opensource so we din't have to worry about the license. The second reason was that, all of our team members was new to PCB design so the learning curve was same for both software but we found a good tutorial series for KiCAD on youtube ( KiCAD tutorials ). KiCAD has its own issues which are discussed in the issue section of this wiki. The steps involved in the PCB design process are described in the next section.

Schematic Design:

Our project can be divided into two main circuits, first is game display circuit and second is a console circuit. We decided to design separate PCB for both circuits as doing so can make wiring easy and improve the user experience.

Display PCB schematic:
Game Display PCB Schematic


Display PCB has two independent circuits. One circuit is to connect SJOne board to LED panel connector and with two piezo buzzers. While another circuit is to connect one unused power cable of LED panel to SJOne board so that we don't have to power SJOne board from PC while we are playing the game. Our preliminary idea was to make this PCB, a Arduino kind of shield but for SJOne board.

Console PCB schematic:
Game Console PCB Schematic


In this game, console is used to move the basket to catch fast falling eggs and if there were any wires attached to console then it is very inconvenient for the user to play. so, we decided to make PCB which can charge battery and power the console while the user is playing. As shown in figure, the heart of the circuit is microchip's MCP73831 LiPo battery charging management IC. One LED is connected to it's Status Pin which glows when the battery is charging. A mini USB B port is used to connect to power resource (PC or any 5V mobile charger)via USB cable to charge the battery. while playing the game, the user must connect USB A port to SJOne Board's mini USB B port. To use the console on battery power user must turn on/off switch.

PCB Layout:

After schematic design, the most important step is to connect the PCB layout. In KiCAD components is not automatically associated with it's PCB footprint, so it's user's responsibility to connect right PCB footprint with the right components. In our case, we did not have the footprint of JLC connector and Rocker switch. so, we created it in a different window and saved it. The amazing feature of KiCAD is once we have done with PCB layout we can visualize PCB in 3D by pressing just one button. Below are actual screenshots of both, PCB layout & their 3D model.

Display PCB layout:
Dispay PCB layout without Copper layer
Display PCB layout with Copper layer
Display PCB front 3D view


Console PCB layout:
Console PCB layout without Copper layer
Console PCB layout with Copper layer
Console PCB front 3D view

PCB manufacturing and soldering:

We chose JLC PCB to manufacture our PCB because, it is the cheapest and convenient option available for any prototype PCB manufacturing. It just cost us $2 for quantity of 10 PCB and $17 for shipment. We received manufactured PCB in just 5 days. We order components from Moser the total BOM cost of both PCB is approx $25 including shipment. Followings are actual photos of manufactured & assembled PCBs.

Actual Console PCB
Actual Display PCB

Hardware Interface

Hardware Design Diagram


Hardware design diagram above gives an overview of the entire system which consists of the two SJ-One controllers: one board is used as Control Module and other board is used as the Display Module.

  • The Console Module uses the onboard accelerometer on SJ-One which is interfaced via I2C protocol. The calibrated accelerometer values are then used to determine the basket position on the LED Matrix.
  • The Display Module SJ-One board is used to control a 32*32 RGB LED Matrix.This matrix displays the basket, eggs shot from the cannon.The movement of the basket is as per the orientation value received from the Control Module, through Wireless Module. It also consists of Peizo buzzer which is controlled via PWM pin.

Software Design and Implementation

Display Module

RGB LED Matrix:

RGB LED matrix display
RGB Display'

The Human Machine Interface is a display which is composed of 6mm pitch 1024 RGB LEDs arranged in a 32x32 matrix. 32 rows of the matrix is divided into 16 interleaved sections. Here the first section is the 1st and 16th 'row' (32 x 2 = 64 RGB LEDs), the second section is 2nd and 17th 'row' and so on. On the PCB is 12 LED driver chips. These are like 74HC595s but they have 16 outputs and they are constant current. 16 outputs * 12 chips = 192 LEDs that can be controlled at once, and 64 * 3 (R G and B) = 192. So now the design comes together. We can have 192 outputs that can control one line at a time, with each of 192 R, G and B LEDs either on or off. The LPC1758 controller selects which section to currently draw (using A, B, C and D address pins - 4 bits can have 16 values). Once the address is set, the controller clocks out 192 bits of data (24 bytes) and latches it. Then it increments the address and clocks out another 192 bits, etc until it gets to address #15, then it sets the address back to #0. To light up an individual pixel, appropriate row value is loaded on to the address pins A,B,C & D, Clock is set out to traverse the row and when required pixel is reached, the latch is set high to turn ON the LED. The hardware interface to the LED Matrix uses GPIO for all data and control lines. A GPIO clock is toggled to shift in data sitting at the Matrix's 6 data ports.

SJ One Board Pin Name Description
P0.0 addrA Address Input A
P0.1 addrB Address Input B
P2.6 addrC Address Input C
P2.7 addrD Address Input D
P1.29 Latch Shift in row data/Active High
P1.28 Output Enable Turn on selected rows/Active Low
P1.19 Clock Shift clock
P1.22 R1 Top half red data
P0.26 G1 Top half green data
P1.23 B1 Top half blue data
P1.30 R2 Bottom half red data
P1.31 G2 Bottom half green data
P2.5 B2 Bottom half blue data

Piezo Buzzer:

Piezo Schematic Diagram
Piezo Physical Diagram

Piezo electric buzzer are high performance buzzer that employ piezoelectric elements and are designed for easy incorporation into various circuits. These buzzers are designed for external excitation, the same part can serve as both a musical tone oscillator and a buzzer. In our project we are using this device to create musical tones by varying the operating frequency.The different range of operating frequency are generated from PWM peripheral. Different range of frequencies are maintained as constants ,these constants are fed to PWM,which generates square wave. The output of the PWM is driving the Piezo buzzer.

Code snippet for creating musical tones by varying frequency:

int fire[]=
{
		550,/*twice the freq of this and use always tempo as 40 */
		404,
		315,
		494,
		182,
		260,
		455,
		387,
		340
};

void fire_sound_level(void){
	 for(int i = 0;i < 8;i++)
		 {
		 	 uint8_t tempo = 40;
		 	 	 while(tempo)
		 	 	 {
					pwm.SetFrequency(fire[i]*2);
					pwm.SetDutyCycle(pwm.k2_1,50);
					pwm.PwmEnableMode(true);
					tempo--;
		 	 	 }
		 }
		 pwm.PwmEnableMode(false);
	}

Control Module

Accelerometer:

Accelerometer Detection
The MMA8452Q which is a smart low-power, three-axis, capacitive micromachined accelerometer with 12 bits of resolution is used in our project. Accelerometers are electromechanical devices that are used to sense acceleration that can be of various forms, for instance gravity.
In our project,we have calibrated the accelerometer based on the values of X,Y and Z co-ordinates corresponding to different orientations of the accelerometer to control the horizontal movement of the Basket int the game to catch the eggs on the screen. This has also helped us decide and control the speed of the basket. As shown in the code snippet below the x movement on the right is determined based on the x co-ordinate and the console sensitivity which you wish to set.Similarly movement on the left can also be calculated for further use.

Code snippet for Accelerometer Calibration:

if (((x_coordiante > px_coordiante + CONSOLE_SENSITIVITY) && (x_coordiante <= CONSOLE_TILT_RANGE) ))
{
        boardOrientation=left;
        bskObj.speed=BASKET_SPEED;
        px_coordiante=x_coordiante;
}
    //left
    else if((x_coordiante<px_coordiante-CONSOLE_SENSITIVITY && x_coordiante>=-CONSOLE_TILT_RANGE))
{
        boardOrientation=right;
        bskObj.speed=BASKET_SPEED;
        px_coordiante=x_coordiante;
}
else if(x_coordiante>CONSOLE_TILT_RANGE ){
        boardOrientation=left;
        bskObj.speed=BASKET_SPEED;
}
else if(x_coordiante<-CONSOLE_TILT_RANGE ){
        boardOrientation=right;
        bskObj.speed=BASKET_SPEED;
    }
else
{
        boardOrientation=invalid;
        py_coordiante=y_coordiante;
}

Wireless Module:

Nordic Wireless Block Diagram
The nRF24L01+ is a single chip 2.4GHz transceiver with an embedded baseband protocol engine, suitable for ultra low power wireless applications. The nRF24L01+ is designed for operation in the world wide ISM frequency band at 2.400 - 2.4835GHz.The nRF24L01+ supports an air data rate of 250 kbps, 1 Mbps and 2Mbps. The high air data rate combined with two power saving modes make the nRF24L01+ very suitable for ultra low power designs. The register map, which is accessible through the SPI, contains all configuration registers in the nRF24L01+ and is accessible in all operation modes of the chip. The embedded baseband protocol is based on packet communication and supports various modes from manual operation to advanced autonomous protocol operation. Internal FIFOs ensure a smooth data flow between the radio front end and the system’s MCU. Enhanced ShockBurst reduces system cost by handling all the high speed link layer operations. Whenever a data is to be transferred over the Nordic Wireless transceiver,a packet containing the required data is made and then transmitted using wireless_send() function to the address of the receiver node. On the other hand, the receiver node waits for the package to be received and once it receives the packet, the data in the the form of X,Y and Z co-ordinates is extracted from the packet and then used to vary the basket position on the display module side. The code snippet below show basic implementation of the Wireless Transmitter and the Wireless Receiver tasks using the Nordic wireless transceiver.
Code snippet for Wireless Transmitter:
 

struct pckt
{
    int16_t x;
    int16_t y;
    int16_t z;
    int16_t buttonPressed=0;
};
void WirelessTx(void *p)
{
       while(1)
       {
           pckt var;
           var.x = AS.getX();/values from accelerometer*/
           var.y = AS.getY();
           var.z = AS.getZ();
           pckt var;
             while(1)
             {
                 if(SW.getSwitch(1))
                 {
                     var.buttonPressed=1;
                     vTaskDelay(300);
                 }
                 else if(SW.getSwitch(2))
                 {
                     var.buttonPressed=2;
                     vTaskDelay(300);
                 }
           wireless_send(REM, mesh_pkt_nack,(pckt*)&var, 8, 0);
           vTaskDelay(50);
             }
       }
}

Code snippet for Wireless Receiver:

void wirelessRx(void* p)
{
    while(1)
    {
        mesh_packet_t rcvPkt;
        int timeout_ms = 50;

        if(wireless_get_rx_pkt(&rcvPkt, timeout_ms)){

            iphObj.x_coordiante = (int16_t)(*((uint16_t*)(rcvPkt.data+0)));
            iphObj.y_coordiante = (int16_t)(*((uint16_t*)(rcvPkt.data+2)));
            iphObj.z_coordiante = (int16_t)(*((uint16_t*)(rcvPkt.data+4)));
            iphObj.buttonPressed= (int16_t)(*((uint16_t*)(rcvPkt.data+6)));
            if(iphObj.buttonPressed==1 )
            {
                xSemaphoreGive(playPauseHandler);
            }
            else if(iphObj.buttonPressed==2 )
            {
               xSemaphoreGive(resetGameHandler);
            }
        }
        vTaskDelay(50);
    }
}


Tasks and Flow Control

List of Free RTOS Tasks
Input Handler Class


Display Handler Class
Game Logic Handler Class


Software Design in Display module:

'Input_handler:' This is class, which contains all the functions which controls the position of the basket. Which is in turn depends on the console unit orientation value received from wireless task. This task also receives status of button press from the console unit. The values are received as a structure. Wireless task checks for button press and accordingly changes the state of game.i.e for button 1 press it pauses the game and for button 2 press it restarts the game. The accelerometer values are used to calibrate the basket horizontal movement.Depending upon the x-axis values of console the basket slides horizontally.

Display_handler: We have implemented the various functions to display the components used in our Game. It uses GFX matrix library to draw the shapes and pixel. Objects used in our game includes Baskets,Eggs,Cannon and Water. Apart form Object display Handler also has functions to implement the screens used in our Game like-Play/Pause screen,Game Over Screen,Win Screen.

Game_Begin: This is a task which divided into Logic Handler, Input Handler and Display Handler. Input Handler read the input,Logic Handler implements various algorithms to generate eggs with random behavior,checks for game Over condition,sliding the basket depending upon the direction received from Input handler,speed of sliding ,Logic to determine the catch or miss of Egg and increment the water level on every miss.Display Handler deals with displaying objects on screen. Each handler class have its manager functions which calls all the private functions of respective handler. From the game Task we call these manager functions of all the handlers.Basic Game theory is to check the input,update the logic and display. we are implementing same thing using handlers for display,logic and input.

Display module screen state flow

Tasks in Console Module :

Transmitter Task: This task periodically transmits the orientation values and button press status to the display module. Task Priority :1 (could be anything as it the only task running in the console).

Testing & Technical Challenges

Issues, Challenges and solutions to get past them

1. RGB LED Matrix Display driver

Porting Adafruit LED driver, which is AVR microcontroller compatible into LPC was challenging because the library was not compatible with LPC1758 micro-controller. As a result, initially all the LEDs were getting turned on. Plenty of changes were done in the existing Adafruit library after which the driver was working as expected. Some of the changes were - to map the LPC GPIOs to LED matrix pins. This was challenging because choosing the pins also mattered for PCB design, which we were unaware until we started to design PCB. We had to remap the LPC GPIO pins to LED matrix as per PCB wiring convenience again. In addition to the basic API functions available, we had to develop many new APIs which were specific to the game using the bitmap to create various re-usable objects. So basically we had to migrate the whole library from AVR to LPC1758.

2. Nordic Wireless

In Nordic Wireless, the transmitted data was received only once, despite the transmitter transmitting data continuously. This was because vTaskStartScheduler() API was used by us.The scheduler_start() API was the right API to be used for Nordic Wireless to function properly. Once we implemented the queue to collect orientation and switch status, we saw a delay in data reception. This was due to usage of scheduler_start() which initializes the wireless_service task.

3. Peizo Buzzer

Determining the range of audio frequencies which would be audible and sensible was challenging.After days of trail and error method we found the range. After finding the range, the problem we encountered was with switching frequencies. Drastically varying frequency of PWM will cause sound produced by Peizo unpleasant.In order to overcome this we had to vary frequency in small steps. Say you want to change frequency from 410 to 510. do it in steps 410,420,430 soon.One more important thing to verify is the whether the frequency generated by PWM peripheral matches your expected frequency, do verify it with logic analyzer once before writing the music tone libraries.

4. Playing tone at all stages of the Game

Display of the objects being delayed, when different tones were played in the back ground. We did not understand what was causing this issue. Due to time constraints we could not further debug more on this. To overcome this would be challenge to us in the near future.

5. PCB issue

For some of the components, KiCAD library was not present so we have to develop our own components and footprint library. One such components was Rocker Switch in display PCB. Designing footprint for this component was really hard as the manufacturer did not give clear measurement/dimensions for the footprint. When we received the components, legs of the switch was slightly thicker than described in datasheet. To overcome this we had to file metal legs in order to fit the switch in PCB.

Our PCB is of 1.6mm thickness while our USB Mini B connector was designed to fit into 1.5mm thick PCB. This made soldering the connector tedious.

SMD IC component in our console PCB which was very difficult to solder by hand. During soldering, we accidentally shorted some pins due to which our console PCB got burnt and we had to re-order the components again.

6. Task Priority

First thing is configuring task priorities and state machine for game state was challenging. We have a total of five tasks. To decide the priority of each task was time consuming, as we dint want the tasks to interfere with the game task which is of lower priority.To over come this we measured the game task execution time and used this time as a block period for higher priority tasks.

Another issue was that the game slowed down as the game level progressed. After debugging, we found out that the issue was due to high RIT_Interrupt rate. The RIT interrupt was very frequent, as a result more of the CPU time was consumed in context switching to interrupt, which slowed down the other tasks. To over come this we reduced interrupt rate by a factor of 20 ,with which the issue was resolved without affecting the LED display refresh rate.

PCB module Testing

We tested LED display with SJOne board using breadboard connection to make sure that there should not be any connection issue in final PCB design. Ones we received our PCB first tested PCB's continuity to make sure that all connections and traces are as expected. Also after soldering components, we did the continuity testing.

Battery charing discharging testing

Console circuit testing was not possible before we design and received PCBs as we don't have main IC and it is available only in SMD. Ones we solder the whole PCB and gave power PCB got burnt, after rigorous testing and debugging we found that we used SPDT switch which connects battery's positive terminal to ground. We solve this problem in next iteration by not connection one lag of SPDT switch after that it worked fine. We configured our IC to charge 400 mAh battery at the rate of 80mAh (preferred configuration in the datasheet). So It takes approx 5h to charge battery ones it fully discharged. We tested our circuit with two full charging-discharging cycles and everything worked as expected.

Display Module and Game Testing

Steps of Testing

1) The RGB LED Display was tested for basic objects like rectangle, line, characters. The flickering of the screen was observed initially with a slow screen refresh rate of anything slower than 5khz. So the refresh rate was fixed at 5khz. Below are snapshots of some of the screens tested.

2) Wireless module was tested by sending a single byte of data. Every time the byte was transmitted, we printed the transmitted value on the Hyperload terminal. Similarly at the receiving SJ one board, we printed the received value. Once this was achieved ,then we reapeted the same procedure with the actual data packet.This whole procedure ensured that the console module is working fine.

3) Once, we had the console module ready, we started integrating the display module and console module. Once we integrated ,we checked for the basket movement while changing the board orientation. Until we had the smooth movement of the basket object on the screen, we continued to finely tune the calibration for accelerometer values.

4) After fine tuning the calibrations, we moved on to test out game algorithms, where the display screen was rigorously tested by playing the game continuously, reversing the console board and trying to see whether display responds. All the stages of game algorithms (the handlers mentioned the software design ) the start screen,end screen, count down screen and display during game was verified.

5) The game algorithm i.e. system testing was done where we tested the screen navigation sequence, difficulty levels of the game (it should not be too easy to win and not too hard to win either). Also every member was asked to play the game for a through testing for robustness of the algorithm. Negative test cases were also tested like pressing the key randomly and likewise.


Basic objects Testing
Count down
Slider Movement Testing
Game End Screeen

Conclusion

At the start, project was a jigsaw puzzle. We only had pieces of knowledge and unaware of how to tailor it to solve the puzzle. Well we are successful in implementing our idea of building a game. This project has helped us to gain practical exposure in building a real time embedded system. This project gave us a platform to utilize all LPC drivers and Free RTOS knowledge which we learnt in our course work and what are the key things to consider while building a real time system. We are thankful to Preet, who motivated and guided us through out the course work.

Project Video

Project Code

GitHub Link : Catch_Me_If_You_Can

References

Acknowledgement

We would like to thank our Professor Preetpal Kang for all his awesome lectures and explanations of the embedded system topics, they could not have been explained any better than this! Not only did we enjoy working on this project but it also gave us an overall learning experience and precious life lessons. We would also like to thank the ISA members for always being around and ready for helping whenever required.

References Used

[1] Nordic wireless datasheet

[2] [1]

[3] Low_Powered_Mesh_Network_stack

[4] KiCAD tutorials for PCB

[5] [2]

Appendix

You can list the references you used.