F17: Viserion

From Embedded Systems Learning Academy
Revision as of 22:25, 10 October 2017 by Proj user7 (talk | contribs) (Schedule)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Viserion Team RC Car

Abstract

This section should be a couple lines to describe what your project does.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

  • Aakash Menon
  • Ajinkya Mandhre
  • Aniket Dali
  • Dheemanth Bangalore Vishwanatha
  • Jean Madassery
  • Omkar Kale
  • Pratap Kishore Desai
  • Pratap Ramachandran

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Week# Start Date End Date Task Status
1 10/09/2017 10/15/2017
  • Research previous projects wiki page, gather useful information
  • Discus about roles and study data sheet of the required parts
  • Setup Git and slack accounts
  • Order components
In progress
2 10/16/2017 10/22/2017
  • Design Hardware layout for the project
  • Start Schematic Design in Eagle.
  • Design High level software architecture.
  • Design data flow diagram for software exchanges.
  • Work on DBC file for CAN exchanges.
  • Study about GPS and Compass calibration .
  • Study Android application software and approaches from previous projects.
3 10/23/2017 29/10/2017
  • Start writing test plans for performing unit testing of each software modules
  • Start interfacing respective components to respective Nodes and do a superficial testing of components.
  • Finish design, prepare Gerber files and order PCB.
  • Identify and document best approach to calibrate Compass
  • Document Android approaches and decide on how to design the app and fix the protocol to exchange data with Bluetooth module.
4 10/30/2017 11/05/2017
  • Develop software modules with TDD approach.
  • Stress test front sensors in different environment conditions (indoor, outdoor, cloudy, sunny..) and collect data with untested code,to check
  • Verify interfaces, power requirements and conditioning required.
  • Start development of GPS and Compass modules and document the efforts and ways to test the algorithm.
5 11/06/2017 11/12/2017
  • Forward the TDD module for QA testing.
  • Start working on sensor mount. (probably prepare design and possibly finish 3D printing)
  • Finish Bearing Angle Calculation.
  • Interface back sensor to Sensor Node and test if controller receives data
  • Mount the parts on PCB.
  • Decide about sensors mount for final design of a car. 3D or some other hardware solution.
  • Finish development of algorithm for Compass & GPS calibration and perform testing.
6 11/13/2017 11/19/2017
  • Fix the bugs on reverted modules and pass it on to QA to re-verify.
  • Integrate hardware/ verified software modules.
  • Verify the connections and working of mounted components.
7 11/20/2017 11/26/2017
  • Connect individual module with master on the physical CAN bus and test the exchanges.
  • Fix the bugs.
  • Mount sensors on car and start working on positioning them properly for maximum coverage
  • Verify the accuracy obtained from GPS and compass module with expected accuracy, fix bugs if required.
  • Test Android Application with dummy data if nodes are not ready.
8 11/27/2017 12/03/2017
  • Sensors should be mounted, working and tested by now. Work on fine tuning and final SW touch.
  • Integrate multiple nodes over CAN and perform integration and system testing.
  • Fix bugs, if any.
9 12/04/2017 12/09/2017
  • If android application and Bluetooth module exchanges are ready, perform outdoor system testing.
  • Analyze, document the bugs, cross verify the bug.
  • Fix the bugs in individual or integrated software/hardware.
  • Perform integration or unit testing to verify that bug is fixed.
10 12/11/2017 12/13/2017
  • Perform round 2 of system testing.
  • Start documenting project report by collaborating artifacts produced during project development.
  • Fix the bugs in system testing.
11 12/14/2017 12/16/2017
  • Perform round 2 of system testing.
  • Start documenting project report by collaborating artifacts produced during project development.
  • Fix the bugs in system testing.
12 12/17/2017 12/19/2017
  • Perform round 3 of system testing.
  • Fix the bugs in system testing.
  • Record a demo to demonstrate project working and features.
  • Complete Documentation of wiki page.
13 12/20/2017
  • Ready for Demo.


Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.