F17: Rolling Thunder

From Embedded Systems Learning Academy
Revision as of 02:15, 6 October 2017 by Proj user2 (talk | contribs) (Parts List & Cost)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Rolling Thunder

Abstract

This section should be a couple lines to describe what your project does.

Objectives & Introduction

Team Members & Responsibilities

  • Central Controller
    • Akil Khan
    • Jerry John
  • Geographical Controller
    • Abhilash Tuse
    • Vishal Rajendra Shrivastava
  • Communication Bridge + Android Application
    • Akinfemi Akin-Aluko
    • Johnny Nigh
  • Motor and I/O Controller
    • Saurabh Ravindra Badenkal
    • Joshua Skow
  • Sensor Controller
    • Sona Bhasin
    • Thrishna Palissery

Schedule

Week # Start Date End Date Task Status Actual Date of Completion
1 09/19/2017 09/25/2017
  • Order components and distribute project modules.
  • Research on project requirements.
  • Research on different sensors to be used.
Completed 09/25/2017
2 09/26/2017 10/03/2017
  • Set up project Git and Wiki page.
In progress

Parts List & Cost

Item # Description Distributor Qty Cost
1 SJOne Board Provided by Preet 5 $400
2 RC Car - Traxxas 1/10 Slash 2WD Amazon 1 $189.95
3 Bluetooth Bee BLE 4.0 Module ebay 1 $15
4 GPS Module Amazon 1 $28.99
5 Compass (CMPS11) Acroname 1 $45.95
6 Traxxas 6520 RPM Sensor Amazon 1 $10.82
7 Traxxas 2991 LiPo Battery and Charger Amazon 1 $199.95
8 Breadboard Jumper Wires Amazon 1 $6.99
9 MIFFLIN Acrylic Plexiglass Clear Plastic Sheet Amazon 1 $9.89
10 Printed Circuit Board Amazon 1 $16.83
11 PCB Mounting Feet Set Amazon 1 $11.99
12 Traxxas 6538 Telemetry Trigger Magnet Holder Amazon 1 $4.63
13 MB1240 XL-MaxSonar EZ4 Ultrasonic Sensor Amazon 2 $73.90
14 Parallax Ping Ultrasonic Range Sensor Amazon 2 $69.98
15 CAN Transceiver Microchip 10 $10.00
16 4D systems 32u LCD 4D Systems 1 $79.00

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.