F17: FoxP2

From Embedded Systems Learning Academy
Revision as of 01:16, 17 December 2017 by Proj user5 (talk | contribs) (Geographical Controller)

Jump to: navigation, search
FoxP2

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

FOXP2

Abstract

This project entails the aggregated knowledge from the Embedded System courses offered at SJSU leveraged into a fully functioning self-driving vehicle. This vehicle will navigate the terrain, avoid obstacles, and relay feedback to the user. The Initialization is enabled using the custom application which will set the final destination using GPS and destination node.

Objectives & Introduction

Show list of your objectives. This section includes the high-level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

  • R Nikfar
    • Team Lead
    • Electrical Circuits Engineering
    • PCB design
    • Sensor testing and implementation.
  • Jason Tran
    • Sensor IO Implementaion, and testing
    • Master controller.
  • Yuyu Chen
    • GPS module implementation
    • Bridge Support
  • Marvin Flores
    • Android Application development
    • Bridge Implementation
  • Rabeel Elahi
    • Master Controller Implementation.
  • Sophia Quan
    • LCD interface
    • Motor Control.
  • Michael Jaradah
    • Unit Testing.
  • Taylor Kearns
    • Testing.
  • Bohan Liu
    • Master Controller.

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Week# Date End Date Task Status Completion Date
1 10/8/2017 10/14/2017 Geographical: Order GPS and Compass

Android: Setup Android Studio; Run test application

Motor: PWM proof of concept

Sensors: Research and requirement for the proper front and reverse sensors. IO design.

PCB: Initial design of PCB without peripherals was Completed.

Master: Research Self-driving car algorithm.

Completed

Completed

Completed

Completed

Completed

Completed

Android & Bridge: 10/21/2017

2 10/15/2017 10/21/2017 Geographical: Interface with micro-controller to receive raw data

Android & Bridge: Initial App UI running. Create a solid plan for checkpoint algorithm.

Motor: Run the car in straight line in manual mode.

Sensors: Purchase and create the protocols and IO.

Master: Start the design of the master controller for all IO.

Completed

On-going

Completed

Completed

On-going

Geographical: 10/21/2017

Android & Bridge: 10/28/2017

3 10/22/2017 10/28/2017 Geographical: Implement algorithm to parse GPS NMEA sentence and calibrate compass

Android & Bridge: Checkpoint algorithm implemented. Phone to SJSUOne board communication setup.

Motor: LCD Display initial integration

Sensors: Initialize testing and debugging on the sensors.

Master: Set priorities for the connected IO, and design a flowchart of the whole system

Geographical: Completed

Android & Bridge: Completed

Delayed due to shipping issues

Geographical: 10/28/2017

Android & Bridge: 11/04/2017

4 10/29/2017 11/04/2017 Geographical: Integrate GPS and compass together to get heading, bearing, and distance

Android & Bridge: Checkpoint algorithm testing. Full Communication with SJSUOne board implemented.

Motor: Implement Speed and Voltage sensor. Full functional motor system that can support Gateway

Sensors: Implement the IO and sensors with the master controller.

PCB: initial design sent out to be printed.

Master: Create and Design the Algorithm to handle IO from sensors and output motor controls.

Completed

Geographical: Completed

Android & Bridge: Completed

Master: Completed

Geographical: 11/04/2017

Android & Bridge: 11/11/2017

5 11/05/2017 11/11/2017 Geographical: Update DBC with Bridge controller and interface with other nodes on CAN bus

Android & Bridge: Other commands such as start and stop implemented and tested. Checkpoint algorithm finalized.

Motor: Implement full functional LCD and Speed sensor feedback control

Sensors: Further testing and fine-tuning of sensors for a fluid and seamless drive.

Master: Testing of Signals, CAN, and behavior of the vehicle.

Geographical: On-going

Android & Bridge: Completed

Master: On-going

Geographical: 11/11/2017

Android & Bridge: 11/18/2017

6 11/12/2017 11/18/2017 Geographical: Calibrate compass with car

Motor: Reverse end to end system integration test

Android & Bridge: Forward commands to GEO board

Sensors: Improve filtering algorithm. Develop proof of concept for TOF sensors.

Android & Bridge: Completed

Motor: Completed

Geographical: 11/14/2017

Android & Bridge: 11/25/2017

7 11/19/2017 11/25/2017 Geographical: Checkpoint algorithm

Motor: Speed integration check for final speed settings

Android & Bridge: Receive messages from GEO & SENSOR. Add features to the app to display sensor values.

Sensors: Compare TOF sensor viability. Look into other forms of measurement such as voltage, etc.

Android & Bridge: Completed

Motor: Completed

Geographical: 11/25/2017

Android & Bridge: 11/25/2017

8 11/26/2017 12/02/2017 Geographical: System testing

Motor: Code freeze after feature complete. Clean up and unit test

Android & Bridge: Implement auto-connect.

Sensors: System testing

Android & Bridge: Completed

Motor: Completed

Geographical: 12/02/2017

Android & Bridge: 12/02/2017

9 12/03/2017 12/09/2017 Geographical: System testing

Android & Bridge: Testing

Sensors: System testing

10 12/10/2017 12/16/2017 Geographical: Testing Android & Bridge: Testing
11 12/17/2017 12/20/2017 Demo autonomous car on 12/20

Parts List & Cost

Item# Part Desciption Vendor Qty Cost $
1 RC Car Amazon 1 240.00
2 SJOne board Preet 7 560.00
3 GPS Module Adafruit 1 40.00
4 Compass Sparkfun 1 15.00
5 Bluetooth Module Sparkfun 1 24.95
6 LIPO Batteries + Charger 1 130.00
7 Ultrasonic sensor Maxbotix 5 150.00
8 PCB Bay Area Circuits 2 75.00
9 DB9 Connector + PCB components HSC 1 40.00
10 CAN Transceiver Microchip 10 20.00
11 LED HeadLights Amazon 1 30.00

Overall Design and Methodology

Eagle Schematic

Board Connection Architecture

Our team's approach to the design of this project was solely based on the integrity of its connections and communication between the nodes. Each node would handle specific parts of the car that would require an extensive amount of computing. At the center of this communication would be our design and printed PCB(printed circuit board). This board was designed in a manner that would reduce the amount of noise within the circuitry of its components, and place its nodes at an optimal location relative to the car.

Insert Picture of the board connections here


Printed Circuit Board

The PCB which is at the heart of this project was designed in Eagle CAD. There were 2 iterations of this board. The first one was designed without validation and had problems with noise within the CAN communications(discussed in problems encountered section). This design lacked several necessary connections and was limited by functionality.


The Second version of the board would incorporate 4 external power outlets that supply 3.3V and 5V to external components as necessary. There would also be an external power unit with regulators that make sure that a clean power is fed to the boards if necessary. As shown in the schematic, the can transceivers are connected to the boards using the terminating resistors. This CAN bus line also connects to the DB9 connections to easily read the CAN data using the PCAN Dongle.

BareBoard
Eagle Board


Connected Board




Before the Board was sent for printing, the rat nests had to be removed and the connections had to be routed in such a way that minimum amount of noise was created. this ensured a robust communication for the CAN bus and stable noise-free power supply for the external components such as the Ultrasonic Sensors.

LCD

The uLCD-32PTU is a 3.2" (240x320) LCD screen with a micro SD connector, GPIO's along with I2C and serial COMMS. Workshop4 IDE was used to program the GUI, and data was transmitted from the SJOne board through UART communication. The LCD displays RPM clicks, GPS heading, bearing, distance, and also the current firmware version and branch name.

LCD Hardware Architecture
LCD Display

Note: The display here shows the angularmeter which will display the rpm, the top right box will display the bearing, heading, and distance from the GPS, and the bottom box will disply the firmware git hash, and branch.

Sensors

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Sensor Hardware Architecture and Interface

Note: Despite the names, the TX and RX pins do not function as asynchronous serial transmit and receive. The TX functions as an open-drain output that pulls the line down when the sensor wants to trigger a cascaded sensor. The RX functions as an digital input that acts as a trigger for the sensor to begin measuring a distance.


Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Sensor Software Architecture


Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Motor Controller

Motor Controller primary tasks are as follows: 1. Control the rear wheels for moving forward, backward and stop 2. Control the front wheels to maneuver 3. Display contents on the LCD

Hardware Design

1. ESC

2. Servo

3. RPM Sensor

4. LCD

Hardware Interface

1. CAN bus

2. PWM to Motor and servo

3. RPM sensor for edge detection

4. UART to LCD

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

1. Init

2. 1 Hz Task

3. 10 Hz task

4. 100 Hz task

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.



Geographical Controller

Geographical Controller primary tasks are as follows:

1. Process data from GPS and Compass module. 2. Navigate to nearest checkpoints and to set destination. 3. Receive checkpoints from Bridge controller.


Hardware Design

CMPE243 F17 FOXP2 geo block diagram.jpg

Hardware Interface

1. CAN bus

2. PWM to Motor and servo

3. RPM sensor for edge detection

4. UART to LCD

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

1. Init

2. 1 Hz Task

3. 10 Hz task

4. 100 Hz task

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Android Application

Main Tasks: 1. Generate checkpoints 2. Send START and STOP commands 3. Display relevant information:

 ** map
 ** current phone location
 ** current car location
 ** connection heartbeat
 ** checkpoint

Software Design

1. Init

2. 1 Hz Task

3. 10 Hz task

4. 100 Hz task

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

SCons - Build Automation

SCons is a build automation tool similar to Make and is based on the Python programming language. The 2 documents below describe the basic usage of SCons to build firmware and unit tests.

File:Cmpe243 f17 foxp2 SCons Build Automation.docx

File:Cmpe243 f17 foxp2 SCons Building Unit Tests.docx


There are 3 build environments defined for the FoxP2 project.

1. ARM build environment

2. DBC build environment

3. Unit test build environment


ARM Build Environment

The ARM build environment utilizes the GNU ARM embedded toolchain to compile code for ARM targets namely for the SJOne Board's LPC1758 powered by an ARM Cortex-M3 (ARMv7-M architecture). Resources used by this build environment include Cortex-M3 specific code, FreeRTOS, start up code, linker scripts, LPC1758 drivers, and finally application-specific code. To build an ECU-specific program, an ECU name can be provided as a command line argument.

DBC Build Environment

The DBC build environment utilizes the default Python interpreter (defined in PATH) and the DBC parser Python tool to generate a C header file. The build environment uses the target ECU name as the target NODE required by the DBC parser.

Unit Test Build Environment

The unit test build environment utilizes the native C compiler on Linux hosts and Cygwin's C compiler on Windows hosts. SCons automatically searches for all unit tests source files in a test directory with file names starting with "test_". When the unit test flag is provided on command line, SCons will build then executed all unit tests. If any unit test fails, the overall SCons build will fail. For Windows, the FoxP2 repository contains pre-built shared libraries (.dll) of Cgreen unit testing library and Cygwin's POSIX references which are linked at run-time.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.