F17: FoxP2

From Embedded Systems Learning Academy
Revision as of 09:47, 15 December 2017 by Proj user5 (talk | contribs) (Team Members & Responsibilities)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

FOXP2

Abstract

This project entails the aggregated knowledge from the Embedded System courses offered in SJSU, leveraged into a fully functioning self-driving vehicle. This vehicle will navigate the terrain, avoid obstacles, and relay feedback to the user.

Objectives & Introduction

Show list of your objectives. This section includes the high-level details of your project. You can write about the various sensors or peripherals you used to get your project completed.


Team Members & Responsibilities

FoxP2


  • R Nikfar
    • Team Lead, Electrical Circuits Engineering, PCB design, Sensor testing and implementation.
  • Jason Tran
    • Sensor IO Implementaion, and testing, Master controller.
  • Ahsan Uddin
    • Git Admin and Motor Control.
  • Yuyu Chen
    • GPS module implementation.
  • Marvin Flores
    • Android Application development and testing.
  • Rabeel Elahi
    • Master Controller Implementation.
  • Sophia Quan
    • LCD interface and Motor Control.
  • Michael Jaradah
    • Unit Testing.
  • Taylor Kearns
    • Testing.
  • Bohan Liu
    • Master Controller.

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Week# Date End Date Task Status Completion Date
1 10/8/2017 10/14/2017 Geographical: Order GPS and Compass

Android: Setup Android Studio; Run test application

Motor: PWM proof of concept

Sensors: Research and requirement for the proper front and reverse sensors. IO design.

PCB: Initial design of PCB without peripherals was Completed.

Master: Research Self-driving car algorithm.

Completed

Completed

Completed

Completed

Completed

Completed

Android & Bridge: 10/21/2017

2 10/15/2017 10/21/2017 Geographical: Interface with micro-controller to receive raw data

Android & Bridge: Initial App UI running. Create a solid plan for checkpoint algorithm.

Motor: Run the car in straight line in manual mode.

Sensors: Purchase and create the protocols and IO.

Master: Start the design of the master controller for all IO.

Completed

On-going

Completed

Completed

On-going

Geographical: 10/21/2017

Android & Bridge: 10/28/2017

3 10/22/2017 10/28/2017 Geographical: Implement algorithm to parse GPS NMEA sentence and calibrate compass

Android & Bridge: Checkpoint algorithm implemented. Phone to SJSUOne board communication setup.

Motor: LCD Display initial integration

Sensors: Initialize testing and debugging on the sensors.

Master: Set priorities for the connected IO, and design a flowchart of the whole system

Geographical: Completed

Android & Bridge: Completed

Delayed due to shipping issues

Geographical: 10/28/2017

Android & Bridge: 11/04/2017

4 10/29/2017 11/04/2017 Geographical: Integrate GPS and compass together to get heading, bearing, and distance

Android & Bridge: Checkpoint algorithm testing. Full Communication with SJSUOne board implemented.

Motor: Implement Speed and Voltage sensor. Full functional motor system that can support Gateway

Sensors: Implement the IO and sensors with the master controller.

PCB: initial design sent out to be printed.

Master: Create and Design the Algorithm to handle IO from sensors and output motor controls.

Completed

Geographical: Completed

Android & Bridge: Completed

Master: Completed

Geographical: 11/04/2017

Android & Bridge: 11/11/2017

5 11/05/2017 11/11/2017 Geographical: Update DBC with Bridge controller and interface with other nodes on CAN bus

Android & Bridge: Other commands such as start and stop implemented and tested. Checkpoint algorithm finalized.

Motor: Implement full functional LCD and Speed sensor feedback control

Sensors: Further testing and fine-tuning of sensors for a fluid and seamless drive.

Master: Testing of Signals, CAN, and behavior of the vehicle.

Geographical: On-going

Android & Bridge: Completed

Master: On-going

Geographical: 11/11/2017

Android & Bridge: 11/18/2017

6 11/12/2017 11/18/2017 Geographical: Calibrate compass with car

Motor: Reverse end to end system integration test

Android & Bridge: Forward commands to GEO board

Sensors: Improve filtering algorithm. Develop proof of concept for TOF sensors.

Android & Bridge: Completed

Motor: Completed

Geographical: 11/14/2017

Android & Bridge: 11/25/2017

7 11/19/2017 11/25/2017 Geographical: Checkpoint algorithm

Motor: Speed integration check for final speed settings

Android & Bridge: Receive messages from GEO & SENSOR. Add features to the app to display sensor values.

Sensors: Compare TOF sensor viability. Look into other forms of measurement such as voltage, etc.

Android & Bridge: Completed

Motor: Completed

Geographical: 11/25/2017

Android & Bridge: 11/25/2017

8 11/26/2017 12/02/2017 Geographical: System testing

Motor: Code freeze after feature complete. Clean up and unit test

Android & Bridge: Implement auto-connect.

Sensors: System testing

Android & Bridge: Completed

Motor: Completed

Geographical: 12/02/2017

Android & Bridge: 12/02/2017

9 12/03/2017 12/09/2017 Geographical: System testing

Android & Bridge: Testing

Sensors: System testing

10 12/10/2017 12/16/2017 Geographical: Testing Android & Bridge: Testing
11 12/17/2017 12/20/2017 Demo autonomous car on 12/20

Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Overall Design and Methodology

Board Connection Architecture

Our team's approach to the design of this project was solely based on the integrity of its connections and communication between the nodes. Each node would handle specific parts of the car that would require an extensive amount of computing. At the center of this communication would be our design and printed PCB(printed circuit board). This board was designed in a manner that would reduce the amount of noise within the circuitry of its components, and place its nodes at an optimal location relative to the car.

Insert Picture of the board connections here


Printed Circuit Board

The PCB which is at the heart of this project was designed in Eagle CAD. There were 2 iterations of this board. The first one was designed without validation and had problems with noise within the CAN communications(discussed in problems encountered section). This design lacked several necessary connections and was limited by functionality.


Eagle Board


The Second version of the board would incorporate 4 external power outlets that supply 3.3V and 5V to external components as necessary. There would also be an external power unit with regulators that make sure that a clean power is fed to the boards if necessary. As shown in the schematic, the can transceivers are connected to the boards using the terminating resistors. This CAN bus line also connects to the DB9 connections to easily read the CAN data using the PCAN Dongle.


Eagle Schematic


Before the Board was sent for printing, the rat nests had to be removed and the connections had to be routed in such a way that minimum amount of noise was created. this ensured a robust communication for the CAN bus and stable noise-free power supply for the external components such as the Ultrasonic Sensors.

Eagle Schematic

Master Controller (Gateway)

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Motor Controller

Motor Controller primary tasks are as follows: 1. Control the rear wheels for moving forward, backward and stop 2. Control the front wheels to maneuver 3. Display contents on the LCD

Hardware Design

1. ESC

2. Servo

3. RPM Sensor

4. LCD

Hardware Interface

1. CAN bus

2. PWM to Motor and servo

3. RPM sensor for edge detection

4. UART to LCD

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

1. Init

2. 1 Hz Task

3. 10 Hz task

4. 100 Hz task

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.