F16: E-Bike

From Embedded Systems Learning Academy
Revision as of 07:23, 18 December 2016 by 146 user13 (talk | contribs) (→‎Hardware Design)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

E-Bike

Abstract

Electrics bicycles are the future of transportation. Our project helps build on this future by advancing electric bike design. We have two motors on the bike. One generates power to charge an on-board battery, while the other propels the bike forward as requested by user input. This allows the user to reach steady transportation speeds without the need to pedal constantly. A more effective future of transportation based on renewable energy is the way forward for us and the planet.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.
1. Allow a motor to propel a bike forward when a button is pressed
2. Create a battery driven power circuit that can support an embedded system and can be charged without a wall adapter
3. Show the user the current status of their battery

Team Members & Responsibilities

  • Nicholas Randhawa
    • Power circuit
    • A/D Converter
  • Alejandro Puente
    • Display battery level to external screen over UART
  • Shared Responsibilities
    • Hardware mounting
    • GPIO drivers
    • RTOS tasks to integrate everything

Schedule

Week # Proposed Completion Date Task Status Actual Completion Date
1 10/28 Finalize project idea and determine hardware requirements Completed 10/28
2 11/04 Order parts Completed 11/04
3 11/11 Draw schematics Completed 11/11
4 11/18 Get A/D on LPC working

Output reading to an external screen

Completed 11/18 (A/D)

12/06 (Screen)

5 11/25 Get MOSFETs working with motors

Finalize power circuit build

WIP TBD
6 12/02 Create RTOS tasks to integrate A/D with the MOSFETs Completed 11/29
7 12/09 Mount hardware and begin testing WIP TBD
8 12/16 Fix defects, finish report, and clean up code Pending TBD

Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Part # Part Name Quantity Cost ($)
1 Bike 1 Free
2 LCD Screen 1 10
3 36V, 10Ah Rechargable Battery 1 250
4 Push Button 1 Free
5 Speed Controller 1 10
6 SJOne Board 1 80
7 Circuit Case 1 Cost
8 Screen and controller case 1 Cost
9 High Power MOSFET 2 4
10 250W DC Motor 1 50
11 50W AC Generator 1 30
12 Boost Converter 1 10
13 Buck Converter 1 10
14 Terminal Block 2 1
15 Resistors 4 Free
16 Diodes 2 Free
17 Nuts 5 Free
18 U-Bracket 2 Cost
19 Small PCB 1 1
20 8mm Motor Arbor Adapter 1 8
21 Skateboard Wheel 1 Free

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

CmpE146 F16 T11 HardwareOverview.png
The figure above shows a high level view of our system on the bike. We have the generator sending power to the main circuit to be rerouted to the battery when needed, the battery getting power from the main circuit and providing power to the circuit, the motor getting power from the circuit, the push button and speed controller on the handlebars sending feedback to the circuit based on user input, and the screen on the handlebars getting data from the circuit.

CmpE146 F16 T11 CircuitSchematic.png
Our hardware design consists of four major sections. The first section of the circuit is the generator which is in yellow on the diagram. Our generator design is driven by a 50W AC generator. It feeds varying voltage to a bridge rectifier circuit to smooth out the signal before going into a boost converter. The boost converter takes the 12-20V input and puts out a steady 42V at 2A. Our boost converter output goes to a MOSFET transistor. This transistor is controlled by a GPIO driver on the SJOne Board. When we want to charge, the MOSFET activates and sends the 42V, 2A electrical energy to the on-board battery. The on-board battery is the heart of our system. It is a 36V, 10Ah lithium polymer battery. Our battery is also the key component for our next major circuit section; the power circuit.
The power circuit sends power to 3 different locations; the ADC, the motor, and the SJOne Board. Starting with the ADC, we are utilizing a voltage divider circuit to step down the voltage to safe, operating levels for the LPC CPU on the SJOne Board. We are using the overcharge voltage of the battery with the ADC to measure how much juice is left in the battery for the user. Next, the power is sent to a buck converter. The buck converter steps down the voltage to the operating 5V that the microcontroller needs to operate. Finally, the battery sends power to the motor.
The SJOne Board is the key component in our next major circuit section which is the microcontroller in green. If the battery is the heart of the system, the microcontroller is the brain. We have it attached to 2 MOSFETs so it can control when we want to charge the battery or use energy to activate the electric bike motor. A user requests motor output through a different GPIO port from an on-board button on the handlebars. When the button is pressed, the SJOne Board will activate the motor MOSFET and the bike will be propelled forward with less pedaling required. The speed of the motor is controlled by a speed controller also on the handlebars. It is basically just a knob that can change the motor speed from zero to max, or 0A to 7A. Finally, the microcontroller contributes to the other major section which is the output of our system.
One of the output components is the motor mentioned already, and the other component is the screen on the handlebars. In addition to the output mentioned for the motor, we have a diode across it to protect our system from any spikes in current that might occur when starting and stopping the motor. Our other output, the screen, displays the battery level so a user knows how much juice they have left. The screen is the best way for our user to know what's going on with the system at any moment.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

CmpE146 F16 T11 ADC.png

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.


The software communication we have created different tasks and functions to handle different events. The way we send data from the board to the screen is shown below in psuedocode:

void uart2_init(uint32_t baud) { 

       clear p2.8 for txd2 and p2.9 for rxd2
       set p2.8 as txd2 and p2.9 for rxd2
       
       clear uart2 clock 
       enable uart2 clock
       set data size as byte
       enable DLAB bit
       calculate speed value
       disable DLAB bit

}

void uart2_putchar(char out) { 

    Store data in buffer
    while(1) {
     if (LPC_UART2->LSR & (1 << 5)) // wait until data is sent
     break;
   }

}

void uart2_end() { 

       uart2_putchar(0xFF); send this 3 times to let screen know were done sending info

}

Implementation

  • Communication between the board and battery
    • The battery talks to the board through the ADC.
  • Communication between the board and the LCD screen:
    • This was done with UART communication. Sending single bytes to update the screen to reflect the proper level of battery remaining.


This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:



My Issue #1

  • Software Challenges:
    • LCD screen, It came with the wrong instructions


  • Hardware Challenges:
    • Mounting the motor to the frame

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

We'd like to thank the Academy.

References Used

List any references used in project.

Appendix

You can list the references you used.

Retrieved from "http://socialledge.com/sjsu/index.php?title=F16:_E-Bike&oldid=31667"