F15: Smart Car

From Embedded Systems Learning Academy
Revision as of 07:18, 19 December 2015 by Proj user22 (talk | contribs) (Motors)

Jump to: navigation, search

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Project Title

Smart Car

Abstract

A smart car with three wheels will be designed to have the capability of following high contrast lines. Options for the lines include using black Sharpie, black duct tape, and white duct tape. Afterwards, it will send back a CSV file format with 0s and 1s. 1s denote that the car was traveling in the area of the map. Using a peripheral compass, the car will also be able to draw a map of the route that it took.

Objectives & Introduction

Our objectives include the following:

  • Self-driving car that is able to follow a line
  • LED matrix that can draw out the path the car is taking

Team Members & Responsibilities

  • Steven Hwu
    • B.S. Computer Engineering
  • Helen Tsui
    • B.S. Computer Engineering

Schedule

Week# Date Task Actual
1 10/23 Complete project abstract Complete
2 10/30 Gather parts Complete
3 11/06 Program compass Complete
4 11/13 Program LED matrix Complete
5 11/20 Program wireless functionality Complete
6 11/27 Build car Complete
7 12/04 Put all the pieces together Complete
8 12/11 Testing Incomplete

Parts List & Cost

Quantity Description Price
2 SJ-One development board $80 ea
1 Cardboard $0 ea
1 White duct tape $4.52 ea
1 Electric tape $1.99 ea
1 Servos $4.47
1 Compass $
2 Motors $80~
2 LED matrix $24.95 ea
2 Photo transistors $1.20 ea
3 Jumper cables $3.99 ea
1 Super glue $3.99 ea
1 Breadboard $6.49 ea
4 NPN transistors $3.29 ea
1 5k potentiometer $2.29 ea
1 Switch $2.99 ea
_______
Estimated total $

Design & Implementation

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here. Cmpe146 F15 smartCarInterface.png

Compass

The compass uses I2C as the communication protocol. The x, y, and z coordinates were able to be read from the compass depending on its orientation. After one of the SJSUOne boards reads the x, y, and z values from the compass, it wirelessly sends the values to the other board to determine which LEDs to light up. The compass' purpose was to determine the car's location so that the path the car was taking could be drawn on the LED matrix.

Cmpe146 F15 smartcar compassInterface.png

LED Matrix

The purpose of the LED matrix was to display the path that the car is traveling. It uses SPI as its communication protocol. The LED matrix consists of 2 x 3 blocks of 8x8 LEDs. It has a few ports that must be utilized for LED programming. The first port is the WR port which is listed as active low. This is actually the serial clock which captures data in its DATA port on rising edges. While the datasheet recommends using an idle LOW serial clock, this is not a must. With the LPC1758, changing the active level of the serial clock is not the solution to this and will cause problems for data transmission to the LED matrix as it will be transmitting data on the falling edge instead and data corruption will occur.

Motors

NPN transistors were used to control the power source to the motors. There was very little documentation for the motors used so initial tests with varying input voltages yielded that these motors seemed to operate successfully at 5V. This method should not be used on documented motors, but instead make sure to adhere to the specifications provided. In addition, if the input voltage is negated, the motor had the ability to rotate in the opposite direction. For the application, only the positive voltage was utilized since the car did not need to go backwards. For turning purposes, one motor moved slower than the other.

SJOne

The SJOne the microprocessor used for this project. The compass and LED matrix were interfaced with the SJOne board. The compass used I2C while the LED matrix used SPI. The wireless functionality of the board was also utilized to in order to send information from one board to another.

Hardware Interface

Communication protocols used:

  1. I2C - HMC5883L Compass
  2. SPI - LED matrix
  3. PWM - Motors

Software Design

The software design utilizes drivers such as SPI and I2C. In addition to the drivers, Nordic wireless functionality was programmed.

Implementation

System Startup

Transmission of x and y Coordinates


Mapping Received Coordinates to LED Matrix

Testing & Technical Challenges

Wireless LED Matrix Testing

To test the LED matrix wirelessly, a sender task was written to allow the sending of three parameters that correlated to the coordinates of each LED on the LED matrix. If the sending was successful, the corresponding LED would light up.

Issues Faced

Wireless communication and LED Matrix

The LED matrix that was used was programmed using SPI0. However, it turns out that SPI0 is shared with the wireless communication API. To fix the issue, the LED matrix was reprogrammed on SPI1.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

References Used

LED matrix HT1632C datasheet: https://www.adafruit.com/datasheets/ht1632cv120.pdf

Appendix

You can list the references you used.