Difference between revisions of "F15: Plant Control"

From Embedded Systems Learning Academy
Jump to: navigation, search
(Software Design)
(Hardware Design)
Line 147: Line 147:
 
<br>
 
<br>
 
'''Water Pump/LED Driver'''<br>
 
'''Water Pump/LED Driver'''<br>
[[CMPE146_F15_PlantControl_PWM.png]]<br>
+
[[File:CMPE146_F15_PlantControl_PWM.png]]<br>
 
               FIgure 2. PWM Mosfet Driver for water pump<br>
 
               FIgure 2. PWM Mosfet Driver for water pump<br>
 
The figure above (Figure 2) dispplays the circuit design used in our plant control system for driving the water pump via PWM. The PWM input from the LPC1758 enters the gate of the 2n7000 mosfet which allows the Source-to-Drain circuit completion. When the Source-to-Drain circuit is complete, the current will flow though the water pump and thus pump water into the dry soil when needed. The LED in the circuit is used to polarize the current so that it only flows in one direction disallowing the pump to receive current in a reverse direction. The circuit for driving the plant lighting LED is similar to the water pump driving circuit other than that the leads to the water pump are connected to a 5V LED. The plant lighting LED is connected in parallel to the forward current directing diode. A 10K Resistor connected from the Gate to the Drain in order to ensure gate is grounded if drive is ever disconnected.
 
The figure above (Figure 2) dispplays the circuit design used in our plant control system for driving the water pump via PWM. The PWM input from the LPC1758 enters the gate of the 2n7000 mosfet which allows the Source-to-Drain circuit completion. When the Source-to-Drain circuit is complete, the current will flow though the water pump and thus pump water into the dry soil when needed. The LED in the circuit is used to polarize the current so that it only flows in one direction disallowing the pump to receive current in a reverse direction. The circuit for driving the plant lighting LED is similar to the water pump driving circuit other than that the leads to the water pump are connected to a 5V LED. The plant lighting LED is connected in parallel to the forward current directing diode. A 10K Resistor connected from the Gate to the Drain in order to ensure gate is grounded if drive is ever disconnected.

Revision as of 07:10, 17 December 2015

Automated Plant Control System

Abstract

The Plant Control project introduces a plant incubator which allows for resource and energy efficiency while producing healthy flowering and vegetation. The incubator will utilize an SJOne development board, its on-board sensors (light/temperature), a moisture sensor, and LEDs in order to autonomously provide the optimal moisture level for growth in any lighting. The owner of the plant control system can be confident that his or her plant is growing in perfect conditions and will be notified otherwise via an LCD screen.

Objectives & Introduction

This project is a self watering, self lighting, and temperature alerting plant grower.
The entire system is controlled via an SJOne Board which utilizes an LPC1758 Microprocessor.

In addition to the onboard sensors, the project will require interfacing to:

  • RGB LCD Screen
  • Moisture Sensor
  • Water Pump
  • PWM controlled LED


Team Members & Responsibilities

  • Moises Negrete
    • LED and Water Pump Driver Circuit Design
    • Temperature, Light Sensor, PWM software
    • Design and Build Planter
  • Eduardo Lemus
    • LCD Interface
    • Source Code Task and Timing Cleanup
  • David Chiu
    • Moisture Sensor Interface
    • Power Regulator Circuit
    • Design and Build Planter

Schedule

Week# Date Task Actual
1 10/24 Research best lighting, temperature, moisture conditions Completed
2 10/30 Purchase necessary equipment, and begin testing equipment (sensors) Completed
3 11/06 Interface Sensors Completed
4 11/13 Interface LEDs and Water Pump Completed
5 11/20 Begin Building Planter Completed
6 11/27 Finish Building Planter & Begin RT Code Completed
7 12/2 Functionality Testing and Prototype Verification Completed
8 12/9 Plant Flower and Field Test In Progress

Parts List & Cost

Part Name Cost
Water Pump $6.99 http://www.amazon.com/gp/product/B00MP4Q6K2?psc=1&redirect=true&ref_=ox_sc_act_title_1&smid=AAOUP5IQ82N49
Soil Hygrometer $6.11 http://www.amazon.com/gp/product/B00KKQYW76?psc=1&redirect=true&ref_=ox_sc_act_title_1&smid=AIOZ1JWV33B58
1/2 gallon Water Reservoir $7.00 Auto Zone
Faux-Ceramic Planting Pot $5.00 Home Depot
Baby Mums (Flowers) $2.00 Trader Joes
SJone Board $80.00 SJSU
Soil $10.00 Home Depot
12V Power Adapter $6.00 Anchor Electronics
LCD Screen $13.90 http://www.seeedstudio.com/depot/grove-lcd-rgb-backlight-p-1643.html
7805 Voltage Regulator $0.50 Anchor Electronics
Total $136.6

Design & Implementation

Hardware Design

The hardware design for this projects will be split into the different sections of our project. The different hardware components include a power circuit and water pump/LED drivers. The
Hardware design will then be followed by the Hardware interfacing components.

Power Circuit
Due to the low power outputs of the LPC1758. in order to drive the LED and the the water pump,
an external power source strong enough to do so is necessary.
CMPE146 F15 PlantControl PowerCircuit.png

              Figure 1. Power Regulator Circuit (12V-5V)


In figure 1, the power circuit uses 2 capacitors (100uF and 220 uF) to maintain stability of the regulator. The LM7805 is used to convert 12V to 5V as needed to power the LCD screen, drive the LED, and the motor. A switch was added at the 5V node in order to be able to switch on and off the 5V.

Water Pump/LED Driver
CMPE146 F15 PlantControl PWM.png

              FIgure 2. PWM Mosfet Driver for water pump

The figure above (Figure 2) dispplays the circuit design used in our plant control system for driving the water pump via PWM. The PWM input from the LPC1758 enters the gate of the 2n7000 mosfet which allows the Source-to-Drain circuit completion. When the Source-to-Drain circuit is complete, the current will flow though the water pump and thus pump water into the dry soil when needed. The LED in the circuit is used to polarize the current so that it only flows in one direction disallowing the pump to receive current in a reverse direction. The circuit for driving the plant lighting LED is similar to the water pump driving circuit other than that the leads to the water pump are connected to a 5V LED. The plant lighting LED is connected in parallel to the forward current directing diode. A 10K Resistor connected from the Gate to the Drain in order to ensure gate is grounded if drive is ever disconnected.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Below are flow charts for the software algorithm combining the tasks that are performing the reading and the tasks that are enabling/disabling the IO devices.

CMPE146 F15 PlantControl Software1.png

               Figure . Water Pump

In the figure above, we have two tasks that control the water pump. The first task (MoistureSensorTask) reads the sensors and the second task (WaterPumpTask) determines whether to turn on the water pump or not.

CMPE146 F15 PlantControl Software2.png

               Figure . LED

In the figure above, we have two tasks that control the LED. The first task (LightSensorTask) reads the sensors and the second task (LightPWMConsumerTask) determines whether to turn on the LED or not.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

My Issue #1

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

We would like to thank both Preetpal Kang and Dr. Haluk Ozemek, for their limitless support and encouragement throughout the semester.
The knowledge and skills gained in CMPE146 were paramount to the completion of this project.

References Used

Soil Hygrometer
LCD RGB Backlight
2N7000 Transistor
Voltage Regulator

Appendix

You can list the references you used.