Difference between revisions of "F14: Team3-Self Driving Car - Optimus Prime"

Latest revision as of 08:55, 14 April 2015

1 Optimus Prime: The Self-driving Car
2 Abstract
- 2.1 Parts List & Cost
- 2.2 Team Schedule
3 Introduction
- 3.1 CAN Bus: A brief introduction
- 3.2 The Six Controllers
4 Design & Implementation
- 4.1 Controller Communication Table
5 Master Controller
6 Motor Controller
7 Sensor Controller
8 Geographical Controller
9 Android & Communication Bridge Controller
10 I/O Unit Controller
11 Conclusion
- 11.1 Project Demonstration Video
- 11.2 Project Source Code
12 References
- 12.1 Acknowledgement
- 12.2 References Used

Optimus Prime: The Self-driving Car

Optimus Prime

Optimus Prime, the self-driving car is an autonomous driving vehicle which is capable of driving itself to its destination using GPS. While it does so, it also avoids obstacles using multiple sensors attached to it. It has an LCD screen to display the useful information about the car in real time e.g. distance to the destination, speed, vehicle battery status, etc. The car can be controlled using an android app. This app was designed and developed specifically for this project. Using this app one can start and stop the car, increase or decrease the speed and set a destination to drive up to. This report is about designing and building this self governing car. This documentation is done keeping in mind the students who want to build their own self-driving car and for the curious ones who just want to know what goes inside an autonomous driving vehicle.

Abstract

A self-driving car comprises of several controllers, each with a specific task dedicated to it. Our car consists of 6 such controllers. We have named them as Master, Motor, Sensor, GPS, Communication Bridge and I/O controllers. They communicate with each other over the CAN bus as shown in the diagram below. Each controller sends out the information over the CAN bus in the form of messages. Every controller receives only the required messages and performs the necessary task. The path navigation is achieved by the GPS. Thus the controllers do the task of a driver and navigate the path by avoiding the obstacles.The overall block diagram of the project is shown below. It includes all six controllers with their sensors and actuators, communicating through a CAN bus.

Parts List & Cost

Item#	Part Desciption	Vendor	Part Number	Qty	Cost
1	RC Car	Amazon.com	Traxxas 37076 Rustler VXL	1	$380.57
2	RC Car Battery	Amazon.com	Traxxas 2926 NiMH 8.4V Hump 3000mAh TRA Connector	2	$67.38
3	CAN Transceiver	Texas Instrument	SN65HVD232D	15	$75.00
4	Assembly Components	Amazon.com, Anchor & HSC	PCBs, Mechnical & Electical Components	NA	$110.80
5	Power Supply	Pololu.com	6V Battery, 5V Regulator	1	$34.85
6	Sonar sensor	Maxbotix	LV-MaxSonar-EZ1 MB1010	3	$99.55
7	Sonar sensor	Given by Preet	LV-MaxSonar-EZ1 MB1010	1	Free
8	Compass Module	Given by Preet	HoneyWell: HMC 6352	1	Free
9	LCD Display	New Haven	NHD-0216B3Z-FL-GBW-V3-ND	1	$27.00
10	Battery Status	Amazon.com	Dc 4.0-30v LED Digital Display Voltage Meter	1	$6.91
11	Bluetooth Bee	Amazon.com	B005GI4HFA	1	$23.00
12	Sensor RPM Long	Sheldon's Hobbies	Traxxas #6520	1	$11.99
13	Wire retainers/Gear Cover	Sheldon's Hobbies	Traxxas #6537	1	$2.99
14	Telemetry Trigger Magnet & Hold	Sheldon's Hobbies	Traxxas #6538	1	$2.99
15	Front Bumper & Screws	Sheldon's Hobbies	TRA2542	1	$9.94
	Total Cost				849.13

Team Schedule

Sl.No	Start Date	End Date	Task	Status	Actual Completion Date
1	09/15/2014	09/16/2014	Order RC Car	Completed on time	09/20/2014
2	09/15/2014	09/16/2014	Order Other parts(Sensor/LCD/Motor Controller...)	Completed	09/20/2014
3	9/30/2014	11/25/2014	Master Controller Team task	Completed	12/18/2014
4	10/06/2014	11/15/2014	Sensor Team task	Completed	11/15/2014
5	9/30/2014	10/20/2014	Motor Controller Team task	Completed	11/25/2014
6	10/4/2014	10/30/2014	Geographical Controller Team task	Completed	12/18/2014
7	10/7/2014	10/30/2014	I/O Team task	Completed	11/25/2014
8	9/30/2014	11/30/2014	Communication Bridge + Android Team task	Completed	11/30/2014
9	10/30/2014	11/01/2014	Complete project integration	Completed	11/30/2014
10	11/30/2014	12/10/2014	Testing Phase-1	Completed	12/10/2014
11	12/11/2014	12/14/2014	Testing Phase-2	Completed	12/14/2014

Introduction

CAN Bus: A brief introduction

Controller Area Network is a serial communication bus which allows microcontrollers to communicate with each other within a vehicle without a host computer. It uses differential transmission on a twisted pair wire which results in high immunity to electrical interference. Each microcontroller works as a node. There are several nodes that are connected to each other through a CAN bus. Each node is able to send and receive messages, but not simultaneously. There is an arbitration scheme which works on message priority. Each microcontroller has its own message ID. Lower message ID represents higher message priority. To learn more about CAN bus communication, visit the following wikipage article.

CAN BUS Tutorial

The Six Controllers

Master Controller
Motor Controller
Sensor Controller
Geographical Controller
Android & Communication Bridge Controller
I/O Unit Controller

Design & Implementation

Controller Communication Table

Controllers
Controller ID	Controller Type
0x01	Master Controller
0x02	Motor Controller
0x03	Sensor Controller
0x04	Geographical Controller
0x05	IO Controller
0x06	Bridge Controller

Common Communication Table
Message Number	Purpose / Data layout
0x101	Get version and boot info
0x102	Get general info
0x103	Synchronize (set) time: byte [0-3] : System time
0x201	byte [0-3] : Version Info byte [4-7] : boot timestamp
0x202	byte [0-3] : Current time byte [4] : CPU usage %

Subscription Rate Info
Byte 0	Effect
0	Off
1	1Hz
5	5Hz
10	10Hz
20	20Hz
50	50Hz
Any other value	Invalid date rate

Master Controller

Group Members

Bhargava Leepeng Chandra
Preeti Benake

Description

Master controller acts as the 'Brain' of the car. It communicates with all the other Controllers on board to implement different Functions. Being the Brain it intelligently processes the data it receives from Sensor, GPS and Bridge controllers to make the car run autonomously. It has several features embedded in it, and controls the car by sending commands to the Motor Controller. In short the master controller actively Receives, Processes and Transmits real-time data.

Master Controller Team Schedule

Week No.	Start Date	Planned End Date	Task	Status	Actual End Date
1	9/30/2014	10/7/2014	* Implement Basic CAN Hardware to communicate between 2 Controllers	Completed We are able to send a message from Tx over CAN and perform a specific operation at the Rx.	10/7/2014
2	10/7/2014	10/14/2014	* Design CAN Acceptance Filter among different Controllers * Define and Implement CAN Frame structure for proper communication establishment	Completed Only messages with in range of acceptance filter are received, Decided on CAN frame structure using 11-bit frame.	10/11/2014
3	10/14/2014	10/21/2014	* Develop Inter-Controller Communication over CAN * Test point-to-point and Broadcast message transmission * Implement a Counter to count and display number of messages	Completed CAN Communication among multiple boards achieved, Point-to-Point & Broadcast modes are working, Able to display the count on 7-Seg Display on SJOne board.	10/19/2014
4	10/21/2014	10/28/2014	* Layout blueprint for Controller and Module positioning * Assemble the RC Car with all the controllers and Modules * Define the Message List by working with other teams * Start working on CAN Periodic message structure	Completed RC car design and module assembly is completed. Need some fine tuning for connections. Message list is generated and periodic message implementation started.	10/28/2014
5	10/28/2014	11/04/2014	* Complete CAN Periodic message structure to transmit Broadcast messages over CAN and establish controlled communication among different controllers * Implement Start condition detection and Fetch boot status from all controllers and display the status of each controller	Completed Periodic Message Setup done. Able to receive boot status. Need to work on display of status.	11/03/2014
6	11/04/2014	11/11/2014	* Design 'Kill Switch' in co-ordination with Motor Controller team and Bridge Controller team * Develop a 'CAN Bus Crash' detection and reset CAN Bus methodology * Design Automatic Head Light turn ON/OFF functionality by working with Sensors Controller team	Completed Kill Switch implemented through Bridge controller. Head Lights implemented. LCD display of Status achieved.	11/11/2014
7	11/11/2014	11/18/2014	* Implement File Log saving to SD Card at periodic intervals * Work on Restoring to last known Status if the system crashes while running * Develop Detection technique if controllers are reaching 'Error State'	Completed File Log implemented. Error State is partially implemented. Obstacle detection achieved. Needed refinement in Direction control logic. Need to implement reverse logic.	11/18/2014
8	11/18/2014	11/25/2014	* Project Integration and testing Basic Self_Drive Capability of the Car * Check the Functionality and behavior of all controllers in all the known contexts * Perform modifications (if any) to eliminate any bugs to make the car work seamlessly * Final Integration of car and testing there after	Completed Integration Started. Faced difficulty in synchronization.	11/26/2014
9	11/25/2014	12/02/2014	* Final Integration and testing Self_Drive Capability of the Car	completed We are able to integrate all the different on-board systems and control the features with the master's control algorithm using real-time data from Sensor, Geo and Bridge controllers. The primary objective of self-drive capability is achieved. We have faced little difficulty in adjusting the frequency of data appropriate to real time needs.	12/8/2014
10	12/02/2014	12/18/2014	* Final Testing with all Features	completed Checked out the Data Log for any possible message drops. Resolved issues related to Compass.	12/15/2014

Hardware Design

An RC car was used as a base to demonstrate the Self-Driven Capability of a car with all the Controlling done by SJOne boards.
The hardware for this Project is custom designed according to the requirements of the project.
This includes building the Chassis to place all the SJOne boards.
Sufficient Power and Ground slots for all the Sensors, GPS, Compass, LCD breakout boards.
Designing a CAN bus structure for establishing communication among different SJOne boards.
Designing a Spike protection for the Input power supply.
Finally Sufficient number of pins(if necessary) to connect external Breakout boards to the SJOne controllers.

Hardware Implementation

First we have started by designing the chassis using a PCB as base to place all the SJOne boards that represents the 6 sub-teams,this includes a separate base for placing LCD module, Head-lights and Tail-lamps.
As a second step we moved forward by designing the circuitry for Power Supply and Spike protection by designing a 5V voltage regulator, that serves as a power supply to all the SJOne controllers and LCD module.
Then sufficient VCC and GND slots were added to the PCB that could accommodate Sonar sensors, GPS and Compass modules, Head-lights and Tail-lamps.
Later a common CAN bus structure was designed to support the CAN transceivers for each individual SJOne board. The entire system is built around this CAN structure.
Then the Hardware was made robust enough to take all the hits during the testing process.

Following is the top view of the car showing the connection of all the 6 controllers and the hardware interfaced to each of them.

Hardware Challenges and Difficulties

The major challenge is to design a common CAN bus structure. One need to understand the electrical characterisitcs of CAN in order to design it better. We had to go through several debugging stages to evaluate the perfromance of the CAN bus as it used to fail at times.
Care must be taken in designing the connections for CAN-HIGH and CAN_LOW. The supply for each CAN needed to be separate in our case in order to provide sufficient drive current to the CAN transceiver.
Next to this another challenge was to make the Hardware robust. During the testing phase it takes a lot of hits and bangs, the module fitting and the circuitary needs to be good enough to absorb all the pressure. By reducing the number of wired connections the robability of hardware fails can be reduced.
Another difficulty was to supply PWM signals to the Motor. The Signals should be strong enough to run the DC motor and Servo motor of the car. It happened to be that if the trace/wire connection is too long the PWM signal is losing its strength. So it should be as much near to the motor as possible.
The positioning of the Sonar sensors should be appropriate to avoid any bounce off, To deal with the bouncing effect we should place it at some height/angular height to reduce the possiblity of bouncing from the ground. Also each sensor should be at a distance and angle with respect to other sensors to facilitate sufficient area of detection.
The positioning of Compass module is a little bit tricky. This should be far away from Electrical/Magnetic interferences as it very sensitive to these effects. So we placed it on the top at a height to avoid any corrupted values.

Hardware Interface

Block diagram of Master controller

Master Controller Pin Connectivity Table
Description	Your Device Port	SJOne Development Board Port
Supply Voltage	Supply +5V	Board +5V
Ground	Supply GND	Board GND
CAN Transceiver	Pin no. 1 Driver Input Pin no. 4 Receiver Output	P0.1 CAN TD1 P0.0 CAN RD1
Head Lights	LED +3.3V LED GND	Pin 1.20, 1.22 GPIO Common GND
LED Strip	LED Strip DIN LED Strip +5V LED Strip GND	Pin 1.29 GPIO Common VCC Common GND

Software Design

Master controller which is the central controller, performs all its functions with FreeRTOS software running at its core.
The two key components of FreeRTOS utilized by Master to achieve these operations are

1. FreeRTOS Task and Scheduler

2. FreeRTOS Queues

Master controller heavily rely on the FreeRTOS scheduler, for most of the time to run various tasks, which are responsible for what the master controller does.
The FreeRTOS queue structure is used to achieve inter-task communication inside the Master controller to process data and transmit to respective controllers.
CAN bus structure with 29 bit message ids is used to establish communication among different controllers. The Broadcast bus made point to point to exchange data between any two controllers by configuring an additional Acceptance filter.
The periodic CAN message structure provided by Preet helps transmit specific data to specified destination at a specified interval like 1Hz, 5Hz, 10Hz etc.
The File logger task runs along with other tasks to log real time data onto SD card in order to facilitate debugging without sacrificing the speed for debugging.
Additional features like Light sensor controlled Head Lights are implemented to make the car feasible for low light/night time runs.
Apart form this an LED strip is used to indicate when the car is being run on sensor's data, when an obstacle is detected. This distinctively demonstrates when the car is controlled by a particular controller among the Geographical controller and Sensor controller.

Software Implementation

The implementation of the specified software design for master controller is achieved by using the FreeRTOS and CAN libraries provided by Preet.
The Master operation starts with the initilization of CAN Bus and configuring the CAN acceptance filter. The sample code is shown below.

In main the control next creates new tasks like Receive task to deal with different functions, which will only start running after the scheduler.
These tasks supply Data to periodic tasks next in the line to Transmit data over the CAN bus to the specified destination.

The FreeRTOS queues exchange data among different tasks to process the data. This comprises data from Sensors, Geo and Bridge Controllers.
The Processed data put into the Decision making algorithm performs direction and speed controlling operations.

The software design and implementation of the master controller is explained by the flowchart.

Implementation

Master Controller Communication Table
Message Number	Purpose	Data Byte Pattern
0x101	Ask for Boot and Version Info. of all Controllers	Byte[0]: Send a '1'
0x103	Sync. Master System Time on all Controllers	Byte[0-3]: System Time [HH:MM:SS]
0x201	Master Gets Status Update from all controllers	Byte[0]: Boot Status Byte[1]: Version Info.
0x203	Master Gets current Time from all Controllers	Byte[0-3]: Time in [HH:MM:SS]
0x301	Master Enable Main UI in Android	Byte[0]: Send a '1'
0x302	Master set GPS Destination on Geo Controller	Byte[0-3]: Latitude Value Byte[4-7]: Longitude Value
0x303	Master set Longitude Way-Points on Geo	bytes [0-1] : Total Way-Points count bytes [2-3] : Way-Point index bytes [4-7] : Longitude(float)
0x304	Master set Latitude Way-Points on Geo	bytes [0-1] : Total Way-Points count bytes [2-3] : Way-Point index bytes [4-7] : Latitude(float)
0x305	Master Send GPS FIX Ack to Bridge	Byte[0]: Send a value '1'
0x306	Master Send Dest. Reached Ack to Bridge	Byte[0]: Send a Value '1'
0x500	Display Boot and Version Info. on LCD	Byte[0]: Boot Status Response Byte[1]: Version Info.
0x501	Display Controllers Time on LCD	Byte[0-3]: Time in [HH:MM:SS]
0x502	Display Destination Has Reached	Byte[0]: Send a '1'
0x503	Master Set Speed and Direction of Motor	Byte[0]: LEFT/RIGHT (or) FRONT/BACK command
0x504	Display Speed of Motor on LCD	Byte[0]: Speed Value
0x505	Display GPS and Compass values on LCD	Byte[0-1]: New Degree to Head Byte[2-3]: Dist to Destination Byte[4-5]: Current Degree value
0x506	Display Sensor Values on LCD	Byte [0]: Front sensor value in inches Byte [1]: Front Left sensor value in inches Byte [2]: Front Right sensor value in inches Byte [3]: Back sensor value in inches
0x507	Display Battery Status on LCD	Byte[0]: Battery Status Value
0x540	Send GPS Data to Bridge	Byte[0-1]: Heading Degree Byte[2-3]: Dist. to Destination Byte[4-5]: Current Bearing Degree Byte[6-7]: Difference between Heading and Bearing angle
0x550	Send Sensor Data to Bridge	Byte[0]: Front Sensor Byte[1]: Front Right Sensor Byte[2]: Front Left Sensor Byte[3]: Back Sensor Byte[4]: Speed value

Testing and Technical Challenge

We have faced several Difficulties during Software design implementation for Master Controller. Some of these issues are discussed here.

Top of the list is the Integration. We have faced difficulty in achieving the integration of all the individual controllers working together in synchronization with each other.
Another issue is the CAN bus communication failure which is due to improper transmitting formats like message ID duplication causing the CAN bus error. There are also issues due to improper configuration of acceptance filter, which is later resolved.
We have also faced difficulty when using the FreeRTOS queues, This is caused due to using a particular queue at some locations before it is actually declared declared.
Apart from this the Queue timing implementation has to be observed carefully as it may conflict the frequency of real time Data that causes error status as the receiving queue task cannot see any data on the queue.
We have faced difficulty in data synchronization during testing. The real-time data needs forced us to modify the Transmitting frequencies from certain controllers, particularly for Geographical controller.

Motor Controller

Group Members

Shashank Tupkar
Naghma Anwar
Shiva Moballegh

Motor Controller Team Schedule

Week No.	Start Date	Planned End Date	Task	Status	Actual End Date
1	9/30/2014	10/7/2014	Study SJOne board's motor controller concepts and PWM	Completed Very simple code. Just two lines. Set the frequency. Set the duty cycle.	10/7/2014
2	10/7/2014	10/14/2014	Open up RC Car's motor and servo connections Study the Electronic Speed Control's functions	Completed Motor and Servo operate on the same frequency ESC needs calibration each time it is switched on. Need to find a solution for this.	10/11/2014
3	10/14/2014	10/21/2014	Define the duty cycles for proper motor and servo signals	Completed Using trial and error, figured out the duty cycle for constant speed and turns	10/19/2014
4	10/21/2014	10/28/2014	Add CAN frame structure to the motor functions Test for communication between motors and sensors for prototype demo Define the Message List by working with other teams	Completed	11/04/2014
5	10/28/2014	11/04/2014	Start working on CAN Periodic message structure Start looking for speed sensors	Completed Bought magnetic speed sensor from Traxxas telemetry from local RC Car store	11/04/2014
6	11/04/2014	11/11/2014	Attach speed sensors to the motor Test CAN communication between motor controller and other controllers	Completed Speed sensors attached	11/11/2014
7	11/11/2014	11/18/2014	Work on speed sensors. Figure out the way to send sensor data to master controller. Test for proper and accurate CAN communication	Completed	11/18/2014
8	11/18/2014	11/25/2014	Project Integration and testing basic self drive capability of the car Check the functionality and behavior of the motor controller in all the known contexts Perform modifications (if any) to eliminate any bugs to make the motor work seamlessly Final Integration of car and testing there after	Completed	12/12/2014

Hardware Design

Parts and their functions

Velineon 3500 Brushless Motor

Motor : Our RC car came with Velineon 3500 Brushless Motor. One of the main drawbacks of brushless motor is that it requires a speed controller to change the field polarity. We can't just give power to the motor directly and expect it to go. We can almost consider the controller as an integral part of the motor itself.

Velineon VXL-3s ESC

ESC : Electronic speed controller was the trickiest part to deal with, since it comes with a previously programmed microcontroller inside it. It needs callibration, for which you need to refer to the user manual. An electronic speed controller basically controls the power given to the motor. Our RC car came with VXL-3s ESC, which accepted 100 Hz PWM input signal whose duty cycle varied from 10% to 20%. When supplied with a 15% duty cycle at 100 Hz, the ESC responded by turning off the motor attached to its output.

Steering Servo : Our RC car was equipped with a digital servo (Traxxas part #2075) for steering control. It does not require an ESC to operate. We can give PWM signal directly to the servo from the SJOne board. The servo accepted 100 Hz PWM input signal whose duty cycle varied from 10% to 20%, where 10% represents extreme right turn and 20% represents extreme left turn.

Steering Servo

Speed Sensor : To measure the RPM and speed of our car, we used the speed sensor provided by Traxxas Telemetry. This magnetic speed sensor worked on Hall effect. To learn more about Hall effect sensors, you can click on this wikipedia article. Since the sensor was provided by the same brand of our car, the installation was quick and easy. Here's a reference video on how to attach magnetic speed sensor to the RC car.

Traxxas 7-Cell 8.4V NiMH Battery Pack

Battery : We used 7 Cell NiMH (Nickel-Metal Hydride) battery pack for our car but would recommend others to use Lipo (Lithium Polymer) batteries instead. NiMH batteries tend to discharge very quickly. Also we realized later that since this car was made for racing purpose, its speed was too fast for our project. We reduced the voltage by removing 2 cells from the 7 cell battery pack. So, go for the 5 cell battery pack instead. A Traxxas EZ-Peak Charger would help a lot while doing testing.

Gears : Gears also play an important role in determining the Speed of the car. A gear is defined by the number of Cogs (teeth) which determines if the gear increases (or) decreases the output speed delivered to the axle. So, we can also opt for different gears to reduce the overall speed in any case necessary. In our case changing the gears isn't an option since our car is set with the minimum gear as it belongs to sports car category. But however some custom gears can still do the job in reducing the unnecessary speed, though they are a little bit hard to get our hands on it.

Hardware Interface

Motor, Servo and Speed Sensor Interface

Motor Controller Pin Connectivity Table
Description	Your Device Port	SJOne Development Board Port	Commands	Note
Supply Voltage	6V from NiMH battery	N/A
Ground	GND (Black Wire)	GND
ESC	Control (White Wire)	P2.0 PWM	PWM motor(PWM::pwm1, 101); motor.set(14.5);	Sets PWM signal of 101 Hz Sets duty cycle of 14.5% for forward movement
Servo	Control (White Wire)	P2.1 PWM	PWM servo(PWM::pwm2, 101); servo.set(15);	Sets PWM signal of 101 Hz Sets duty cycle of 15% for no turn
Speed Sensor	Signal (White Wire)	P2.2 PWM		It contains a trigger magnet and an rpm sensor It works on Hall effect.
CAN Transceiver	Pin no. 1 Driver Input Pin no. 4 Receiver Output	P0.1 CAN TD1 P0.0 CAN RD1		TI CAN Transceiver SN65HVD232D Pin 7 - CAN H & Pin 6 - CAN L

Software Flow

Implementation

Motor Controller Communication Table
Message Number	Purpose	Data layout
0x508	Speed Sensor Data	byte [0] : Speed sensor value in rpm
0x503	Vehicle Direction/Movement Data	byte [0] : Movement Control 0x1 : Forward Fast 0x2 : Forward Slow 0x3 : Right 0x4 : Left 0x5 : Stop 0x6 : Back Right 0x7 : Back Left 0x8 : Back

Testing and Technical Challenge

Motor Controller
- ESC
  - Electronic Speed Control is tricky to handle since it has its own pre-programmed micro-controller inside it which needs calibration according to the user manual.
  - We started with calibrating the ESC using RC car's transmitter, but later we had to write our own calibration code.
- Motor
  - We tested the motor speed by measuring the PWM signal on oscilloscope. We started by reading the PWM signal on oscilloscope while manipulating the speed of the RC car using its transmitter module.
  - Since the car was made for racing purpose, we had to keep the speed to its lowest value.
  - The transmitter and receiver of the RC car was detached from it. We gave PWM signal to the ESC and Servo through SJOne board.
  - It turned out that ESC was not accepting the PWM signal because it needed calibration each time its setting is changed.
  - We overcame this problem by including a calibration init code in our program.
  - We also noticed that as we added more hardware on top of the car, its speed was affected because of the load. We had to change the PWM value accordingly.
- Servo
  - Since servo was not connected to the ESC it was pretty easy to handle. We could give PWM signal directly to servo and it moved accordingly.

Sensor Controller

Group Members

Deepak Yadav
Vinod Pangul

Sensor Team Schedule

Sl.No	Start Date	End Date	Task	Status	Actual Completion Date
1	10/6/2014	10/18/2014	Order Ultra Sonic Sensors	Completed [Got two sensors (front and back), 2 more (front right & left) to order ->Completed.]	10/19/2014
2	10/9/2014	10/9/2014	Sensor Data Sheet review with the team	Completed	10/9/2014
3	10/9/2014	10/16/2104	Sensor code development	Completed (Implementing filter (HW/SW) to get more accurate data ->(Done). Add logic to get the rest of the three sensor(front right/left and back data)->(Done) (Note: Delayed due to the implementation of CAN structure and calibration of IR sensor)	10/21/2014
4	10/22/2014	10/25/2014	Sensor software testing	Completed	10/25/2014
5	10/25/2014	10/28/2014	Sensor real time testing	Completed	10/28/2014
6	10/13/2014	10/15/2014	Light sensor code Development	Completed	10/14/2014
7	10/13/2014	10/15/2014	Accelerometer sensor code Development to detect tilt	Completed	10/14/2014
8	10/15/2014	10/15/2014	Light Sensor and Accelerometer Testing	Completed	10/15/2014
11	11/03/2014	11/04/2014	Common Communication SW code implementation and testing	Completed	11/04/2014
11	11/04/2014	11/09/2014	Complete Hardware testing-1	Completed	11/09/2014
12	11/10/2014	11/15/2014	Complete Hardware testing-2	Completed	11/15/2014

Sensors : Sonar Sensors + Light and Accelerometer sensor

Hardware Design

A) Sonar Sensor:

The LVMax long distance sonar sensors are used to detect the objects. We used four such sensors, three in the front and one in the back to get wide angle vision for the car. The Sonar Sensors sends sound waves when triggered and then the sensor signal emits a PWM that needs to be timed to detect the distance. The PWM width depends on the time it takes for the sound waves to bounce back from an object. The following figure explains how the distance is calculated.

B) Light and Accelerometer Sensor:

The inbuilt accelerometer and light sensor on SJoneBoard is used to read their values. The inbuilt driver libraries provide by Prof. Preet is used to read both the accelerometer and the light sensor value and broadcast it over CAN bus for the detection of Car's light and front light of the car.

Software Design

Sonar Sensor

Configure PW as input
Enable PW as Rising and falling edge interrupt
Configure RX as output, and give a 20uS Pulse of HIGH then LOW
Take a snapshot of a hardware timer (T1) or start a hardware timer When Rising edge interrupt occur on PW.

--> After few microsecond <--

PW will go HIGH,take a snapshot of a hardware timer or start a hardware timer When Rising edge interrupt occur

--> After some time <--

PW will go LOW and the interrupt on falling edge will now trigger, Take a snapshot of a hardware timer (T2).
Calculate the time difference (T2-T1) and convert the time into inches/CM (Formula is provided by the datasheet).

Light and Accelerometer

The library provided with SJOne Board has drivers for light and Accelerometer sensors. The only thing is to be done is to read the light sensor and accelerometer sensor data and broadcast to Master controller over CAN bus at rate of 1Hz.

Sensor Controller Task

Below is the overall flowchart of the sensor controller task.

Implementation

Sensor Controller Communication Table

Message Number

Purpose

Data layout

0x510

Front/Back Range Sensor Data

byte [0] : Front sensor value in inches
byte [1] : Front Left sensor value in inches
byte [2] : Front Right sensor value in inches
byte [3] : Back sensor value in inches

0x511

Accelerometer/Light Sensor

byte [0] : X axis Value
byte [1] : Y axis Value
byte [2] : Z axis Value 
byte [3] : Light sensor value

Testing and Technical Challenge

Front and Back Sensors Controller
- To test the Sonar sensors, We placed the object in front of the sonar sensor and checked the pulse generated by the sonar sensors on Oscilloscope. The sensors data is verified by printing it on the Output terminal. We also tested the working of sensor with the moving car. We logged the data on the SD card and also displayed it on the seven segment display when the car was moving.

We used Maxbotix LV-MaxSonar sensors. It has Three mode for getting data-Pulse width (PW), Analog (AN) and RS232. We went for Pulse width mode, because RS232 found to be very inaccurate and needed more pin connections (RX,TX,GND and 4 UART), SJOne board has only three available analog pins for use and we needed 4 of them and also they were not fast enough and their minimum distance is only 6 inch. So, we decided to go for Pulse width mode. The PW mode are much accurate and they are fast. Their distance range is from 3 inch to 254 inch. Moreover, PW can be connected to GPIO pins with external interrupt functionality. Since SjOne Board has more available GPIO pins on Port2 with external Interrupt functionality, PW mode option was chosen.

The sonar sensors needs some time of delay to complete the full distance reading if no object is detected within the max range.The delay is ~50ms for each sensor to complete the distance calculation. So, a min 50ms delay is needed between every next triggering of RX pin. The value provided by the sensors are accurate, but not very stable. We tried using mode filters to avoid unstable readings. The only drawback of using filters was that it slowed down the sensors reading. After few experiment we found out that sensors are much more stable and provide a very accurate reading when we put a large delay around 20 ms between toggling the trigger pin (RX) and polling on CPU and not using external interrupt for calculating the distance time. This method is a very bad design as it can consume unnecessary CPU time, and its max range is not accurate and fixed (due to timeout delay), and it may give inaccurate reading if any interrupt occur. Since sensor task had no other major task running and after few experiment we found out that without using external interrupt and just polling the sensor value (bad design approach) was more reliable and accurate!!. The future implementation would be to find the solution to get the more reliable and accurate data using external interrupt function.

Geographical Controller

Group Members

Bhushan Gopala Reddy
Ryan Marlin
Rishikesh Nagare

Geographical Team Schedule

Sl.No	Start Date	End Date	Task	Status	Actual Completion Date
1	10/4/2014	10/13/2014	Research and Order GPS module	Received GPS module	10/7/2014
2	10/7/2014	10/18/2014	Interface GPS module with LPC1758	Finished	10/17/14
3	10/14/2014	10/18/2014	Receive Compass module from Preet	Received	10/9/2014
4	10/18/2014	11/4/2014	Parse GPS data and setup constructs to send appropriate data	Finished	11/1/2014
5	10/14/2014	10/18/2014	Interface the Compass Module	Finished	10/16/2014
6	10/25/2014	11/4/2014	Calibration of Compass	Finished	11/1/2014
7	11/4/2014	11/11/2014	Integrate GPS and Compass data	Finished	11/4/2014
8	10/25/2014	11/30/2014	Testing and mapping of GPS co-ordinates	Finished	11/20/2014
9	11/18/2014	12/18/2014	Final integration and testing	Finished	12/15/2014

Hardware Design

Hardware Interface

Geographical Controller Pin Connectivity Table
Description	Your Device Port	SJOne Development Board Port
Supply Voltage	Vcc	3v3
Ground	GND	GND
GPS Module	Channel 1 -> Rx, Channel 2 -> Tx	Channel 1-> Tx P2.8, Channel 2-> Rx P2.9
Compass	SCL SDA	SCL2 -> P0.11 SDA2 -> P0.10
CAN Transceiver	Pin no. 1 Driver Input Pin no. 4 Receiver Output	P0.1 CAN TD1 P0.0 CAN RD1

Software Design

The figure above shows a top level view of the geographical team's software flow. The main message task, shown in the middle, is responsible for handling and updating the CAN message pointer. The CAN message pointer is read and handled in a separate periodic task that runs and sends messages across the CAN bus at frequencies of 1, 5, 10 or 20 Hz.

The GPS and compass tasks, shown on the left and right respectively, collect their respective data and send that data to the message task. The message task will grab this data and stuff the CAN message variable to be sent to the Master module.

GPS
NMEA (National Marine Electronics Association)

NMEA consists of sentences, the first word of which, called a data type, defines the interpretation of the rest of the sentence.
Each Data type would have its own unique interpretation and is defined in the NMEA standard.
In our project we are using RMC (Recommended Minimum GPS data).Below is an example of RMC data.

$GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4,230394,003.1,W*6A

Where:

    RMC          Recommended Minimum sentence C
    123519       Fix taken at 12:35:19 UTC
    A            Status A=active or V=Void.
    4807.038,N   Latitude 48 deg 07.038' N
    01131.000,E  Longitude 11 deg 31.000' E
    022.4        Speed over the ground in knots
    084.4        Track angle in degrees True
    230394       Date - 23rd of March 1994
    003.1,W      Magnetic Variation
    *6A          The checksum data, always begins with *

Connection and Software Flow GPS:

SJone board and GPS module is connected using UART. At boot-up GPS tries to get fix for all possible satellites to get proper GPS values.

Compass
The Compass works over the I2C bus interface. Based on the datasheet, the compass will send data when it receives a 'A' command.

Implementation

GPS Controller Communication Table
Message Number	Purpose	Data layout
0x518	Send GPS Data to Master	byte [0] : New Degree byte [1] : Distance byte [2] : Current Degree
0x519	Send GPS FIX ACK to Master	byte[0]: Send a '1'
0x52A	Send Destination Reached ACK to master	byte[0]: Send a '1'

Testing and Technical Challenge

Geographical Controller
- GPS
  - GPS data was relatively straightforward to receive, however we ran into quite a few issues trying to parse the data.
  - Often times we would read the UART data in the middle of the buffer being changes to the next data point, for example, the reading would look like this:
    - $GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4$GPRMC,123519,A,4807.038
    - Instead of the normal data point: $GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4,230394,003.1,W*6A
  - By checking the Checksum at the end of the string, *6A, we were able to determine the number of characters that were supposed to be in the string and exclude any strings that did not have the correct number of characters.
- Compass
  - The Compass data was also straight forward to get. The compass HMC6352 has many useful features as provided in the datasheet, We focused on using the basic output data mode with heading mode.
  - The Compass is very sensitive to any kind of magnetic interference. In our project it were the motors and we had to make sure we mount the compass as far as possible from the motors to avoid any interference even though we had the calibration mode set up.
  - Sometimes the SDA and SCL used to get short (not because of hardware problem) maybe due to line impedance or parasitic capacitance since the wires were close to each other. A software reset can solve the problem.

Android & Communication Bridge Controller

Group Members

Chia-Pin Tseng (Ben)
Johnny Yam
Kevin Beadle

Communication Bridge & Android Team Schedule

Sl.No	Start Date	Planned End Date	Task	Status	Actual End Date
1	9/30/2014	9/30/2014	Obtain Bluetooth Module (already had one)	Done	9/30/2014
2	9/30/2014	10/14/2014	Develop Basic Android App with Bluetooth Sensor Communication	Done	10/7/2014
3	10/11/2014	10/14/2014	Interface Bluetooth Module with SJSU Dev Board	Done	10/11/2014
4	10/12/2014	10/19/2014	Be able to send bi-directional arbitrary messages between Android App and Dev Board via Bluetooth	Done	10/14/2014
5	10/14/2014	11/21/2014	Subscribe to all CAN messages and dump all of them via Bluetooth to Android App or web interface	Done	11/24/2014
6	10/14/2014	11/21/2014	Ajax & Websocket server remote structure	Done	11/01/2014
7	10/14/2014	11/21/2014	Be able to input GPS coordinates through either (or both) Android App and web interface and send through Bluetooth then CAN bus	Done	11/24/2014
8	10/21/2014	11/24/2014	Android App and webpage GUI enhancements (Google Maps, Google Drive)	Done	11/24/2014
9	10/21/2014	11/30/2014	Data visualization (status, compass, speed, location,....)	Done	11/30/2014

Hardware Design

Bluetooth Bee Module

In order to facilitate wireless communication between the SJSU One Board and a Android device, a Bluetooth Bee module is used. This module was chosen because it can connect and mount directly onto the SJSU One Board's XBee breakout socket.
The Bluetooth Bee is a Serial Profile Port (SPP) Bluetooth interface that connects with the SJSU development board's UART3.

Hardware Interface

The relevant pin connectivity table between the Bluetooth Bee module and the SJSU One Development Board is shown below:

Communication Bridge Pin Connectivity Table
Description	Bluetooth Bee Port	SJSU Development Board Port	CAN Transceiver
3.3V Supply Voltage	3V3	3V3	3V3
Ground	GND	GND	GND
UART Channel 1	TX	RX
UART Channel 2	RX	TX
CAN TXD		CAN TD1	TXD
CAN RXD		CAN RD1	RXD

The Bluetooth Bee Module interfaces with an Android device through Bluetooth. In addition, various commands and data are then sent and received to and from the CAN bus through the Bluetooth Module to the Android device.

Software Design

The bridge controller and Android APP work as routers

Bridge Controller

Bridge controller translates CAN bus data into plain text and send it to android platform
The Bridge controller is comprised of the SJSU Development Board with the Bluetooth Bee Module.
The Bluetooth Bee Module can be configured by writing to UART3 specific commands as specified in the Bluetooth Bee Seeedstudio Wiki.
The Bluetooth Bee Module was configured as SLAVE MODE via the command: \r\n+STWMOD=0\r\n (The Android device will act as the Bluetooth Master)
The Bluetooth device name was set to "Yam_BluetoothBee" using the command: \r\n+STNA=Yam_BluetoothBee\r\n
Allowing other devices to connect to the Bluetooth Module was enabled using the command: \r\n+STOAUT=1\r\n
Finally the Bluetooth Bee Module started broadcasting/inquiring to connect to another device using the command: \r\n+INQ=1\r\n
There are many other commands, such as to change the default pincode value, but they were not used for this project.

Bridge framework

The architecture for our bridge controller is to interconvert the data between Bluetooth message and CAN bus message. Bluetooth message uses simple plaintext to transfer data. However, before we can deal with the string data, to collect and assemble several bytes into a package is needed, because UART is byte based data transmission. I use a byte 0x13(which is ‘\r’ in C code) at the end byte.The bluetooth sender must send 0x13 in the end of every text message. This process is achieved by BluBeeTask_BT2CAN class. CAN bus message uses 29bits as message ID and 8bytes data length as a single package to communicate with the master controller. There are two main classes for the controller. BluBeeTask_BT2CAN and BluBeeTask_CAN2BT.

BluBeeTask_BT2CAN

BluBeeTask_BT2CAN is responsible for receiving the data which comes from bluetooth(via UART).We can setup multiple message filters to receive and process certain message data.

Filter setting format.

    blutoothReceiverTask->addCMD(
    BluBeeTask_BT2CAN::CMDProp::gen((char* cmd,
               bool (*func)(BluBeeTask_BT2CAN *, char* CMDStr)));

For example, there is a message format “Speed” to control the speed of the automatic car. We can simply apply a filter as below

    blutoothReceiverTask->addCMD(
    BluBeeTask_BT2CAN::CMDProp::gen("Speed", SpeedCMD));

then, we have a callback function “SpeedCMD” that can only receive speed setting messages.(For instance there is a message “Speed23” was sent by Android)

    bool SpeedCMD(BluBeeTask_BT2CAN *sender, char* CMDStr)//CMDStr will be “23”
    {
        int speed = 0;
        CMDStr=parseInt(CMDStr,&speed);//parse string “23” into integer 23
        can_msg_t msg = { 0 };//CAN message
        msg.msg_id = make_id(cid_master_controller, CAN_TX_CAR_SPEED_MSG_ID);
        //Set the ID to send to master controller with speed message ID 
        *(int *) &(msg.data.bytes[0]) = speed;//First byte is the speed 23
        return sender->Send2CAN(msg);//Send message via CAN bus
    }

You can see the call back function SpeedCMD is doing a very simple string processing, then, send it to the master controller via CAN bus.

BluBeeTask_CAN2BT

What BluBeeTask_CAN2BT doing is actually very similar to BluBeeTask_BT2CAN. First, you need to apply CAN message filters and set the corresponding callback functions.

Filter setting format.

    CANReceiverTask->addMsgTamp(
           BluBeeTask_CAN2BT::MsgProp::gen(
                 (controller_id_t MsgIdTmp, controller_id_t Mask,
           bool (*func)(BluBeeTask_CAN2BT *, can_msg_t Msg)));

controller_id_t is the set of information of CAN message ID including source, destination, and message number. To setup a controller_id_t variable you can simply use a function make_id.

    controller_id_t ID= make_id(destination,source,message Number);

MsgIdTmp is the message ID that you wanna receive. Bit 1 in mask means that certain bit you need to compare between MsgIdTmp and received message ID.

CAN message mask example
received message ID [00,12,07] MsgIdTmp [20,12,31] Mask [00,FF,00] Success First mask data 00 means ignore the first data difference between received message ID and MsgIdTmp(ignore 00!=20). Second mask data FF means you need to compare the second data. In this case both are 12, therefore, it passes the comparison Third mask data is 00 (ignore 07!=20).	received message ID [00,12,07] MsgIdTmp [20,12,31] Mask [00,FF,FF] Failed Third mask data is FF, so we need to compare 07 and 31. Apparently, 07 is not equal to 31, so the comparison is failed.

For example, there is a compass message comes from master. We can simply apply a filter as below

   can2btptr->addMsgTamp(
           BluBeeTask_CAN2BT::MsgProp::gen(
                   make_id(0, cid_master_controller,
                           CAN_RX_DA_COMPASSSTATUS_MSG_ID), //Message ID templete
                   make_id(0,0xFFF,0xFFF)//Mask means don’t compare source section
                   , compassMSG));//Set Callback function compassMSG

We have a callback function “compassMSG” that can only receive compass messages and whichmessage was come from master controller. Since bridge controller receive this information, so we don’t need to compare destination.

 bool compassMSG(BluBeeTask_CAN2BT *canbt, can_msg_t Msg)
 {
     sprintf(STRBUFF, "geo::%d,%d,%d,%d\r", (int16_t) Msg.data.words[0],
           (int16_t) Msg.data.words[1], (int16_t) Msg.data.words[2],
           (int16_t) Msg.data.words[3]);
     //convert those data into a string
     //notice the end of the string is ‘\r’, which is needed
     canbt->Send2BT(STRBUFF);// send to UART(Bluetooth)
     return true;
 }

Android Controller

Android platform receives the text data from bridge controller, then, transmit the data through ajax or websocket
External controller could be any TCP accessible device (simple pebble watch program (20 lines) are used to control start and stop)
One administrator(control and receive), multiple observers(only receive)
Number of way points and routing is dynamically determined and done using the Google Maps API

Bridge framework

cross platform

Intro

Implementation

Communication Bridge Communication Table
Message Number	Purpose	Data layout
0x528	Set Car Speed (Kill Switch) - temporary allow for other non-zero value for demo	byte[0] - speed value
0x529	Destination GPS location	bytes [0-3] : latitude (float) bytes [4-7] : longitude (float)
0x52A	Turn to degree	bytes [0-3] : degree(float)
0x52B	Way points longitude	bytes [0-1] :total waypoints count bytes [2-3] :waypoint index bytes [4-7] : longitude(float)
0x52C	Way points latitude	bytes [0-1] :total waypoints count bytes [2-3] :waypoint index bytes [4-7] : latitude(float)
0x52D	remote status (ie. Android connection status)	bytes [0]=> 0:disconnected(passive send) 1:on disconnect(active) 2:connected(passive) 3:on connect(active) 0xFF:error(active/passive)

Testing and Technical Challenge

TESTs

100000 message(20bytes per message) Bluetooth transmission between board and android under 200fps with range <5m
- 100% success

ISSUE

3G network server could not be access(3G network is used for long range communication)
- might use google sheet or external server to communicate

I/O Unit Controller

Group Members

Shreeram Gopalakrishnan
Sreeharsha Paturu Gangadhara

IO Team Schedule

Sl.No	Start Date	End Date	Task	Status	Actual Completion Date
1	10/7/2014	10/13/2014	Research and Order LCD Display	Ordered LCD Display	10/13/2014
2	10/14/2014	10/21/2014	Interfacing LCD Display with LPC1758	Completed	10/21/2014
3	10/21/2014	10/28/2014	Implementing CAN structure with LCD tasks.	Completed	11/30/2014
4	10/28/2014	11/04/2014	Subscribe data from sensor and GPS controller,display it on LCD.	Completed	11/08/2014
5	11/04/2014	11/11/2014	Setup hardware and write code for START, STOP and Headlight buttons.	Completed	11/12/2014
6	11/11/2014	11/18/2014	Testing and mounting hardware on car.	Completed	11/27/2014
7	11/18/2014	11/25/2014	Final Testing	Completed	12/15/2014

Hardware Design

The IO Control Unit manages the LCD Display, switch to start and stop the car
It receives CAN data from the Master controller and accordingly processes to display on the LCD through UART
The 7 segment LED displays the CPU usage

LCD Display

The LCD Display is placed on the rear side of our RC Car
It displays the sensor and GPS values in real time.

Hardware Interface

LCD hardware interface

I/O Controller Pin Connectivity Table
Description	Your Device Port	SJOne Development Board Port	Commands	Note
Supply Voltage	5V supply			Receives 5V supply that is used to power up all the boards
Ground	GND	GND
LCD Display	Rx pin Tx pin	Rx ---> TXD2 (Port 2.8) Tx ---> RXD2 (Port 2.9)	u2.putline("F0") u2.putline("$CLR_SCR") u2.putline("$GOTO:3:0")	Initialization command for LCD Clears the screen Point the cursor to line number 0 and character number 3
CAN Transceiver	Pin no. 1 Driver Input Pin no. 4 Receiver Output	P0.1 CAN TD1 P0.0 CAN RD1

Software Design

LCD Software Interface

Implementation

|

IO Communication Table
Message Number	Purpose	Data layout
0x102	Send boot status and version info	bytes [0-2] : Status and version info
0x505	Display GPS and compass values	Byte[0-1]: New Degree to Head Byte[2-3]: Dist to Destination Byte[4-5]: Current Degree value
0x506	Display Sensor Values	Byte [0]: Front sensor value in inches Byte [1]: Front Left sensor value in inches Byte [2]: Front Right sensor value in inches Byte [3]: Back sensor value in inches Byte [4]: Speed value

Testing and Technical Challenge

LCD junk values

->Junk values being printed:

Although this error was not a show stopper, LCD printed junk values whenever it was on and any of the boards were programmed.
- So, the only solution was to never program the board (connect the board to laptop) when LCD is on.

->Coding improvement

In the code, initially, the GPS, Sensor values were being printed in one line in the code. So, either the values were overwritten or there was shifting of those values. This was a synchronization issue.
- Resolved it by, clearing each line in the LCD before printing it and used individual line in the code to print the values.

Conclusion

The whole project experience was fun and very educational. We learned about how CAN bus, sonar sensor, accelerometer sensor, light sensor, gps and compass module and motor controllers works. We faced some technical challenges such as controlling the motor speed, getting the right distance value from the sonar sensor, getting accurate readings from gps and compass and some of the power issues such as the right amount of current to the DC motors.

This project can be expanded to include more features such as an sonar sensor connected to the servo motor that rotates 360 degree to get distance from all the sides. This can reduce the number of sonar sensors. Furthermore, a improvement can be done in master and motor controller to control the car more precisely by controlling the car movement more accurately. A future suggestion would be to avoid non avoidable obstacles such as grass or follow only the planned route (may be be using some sensors or image detection).

Project Demonstration Video

CmpE243_F14_T3_ProjDemo

Project Source Code

Sourceforge Source Code Link

References

Acknowledgement

We would like to thank our instructor Preet for always inspiring and encouraging us to learn and build cool projects related to embedded systems. We really appreciate his patience and his guidance. This was our first exposure to CAN bus communication and we learned a lot about it. Last but not the least we would like to thank our awesome team members for supporting each other and helping each other out while working on this project.

References Used

http://www.ti.com/product/sn65hvd232

http://www.socialledge.com/sjsu/index.php?title=Self-driving_Car

http://www.nxp.com/documents/user_manual/UM10360.pdf

http://www.socialledge.com/sjsu/images/d/de/2012SJOneBoardSchematic.pdf

http://www.maxbotix.com/documents/MB1010_Datasheet.pdf

http://www.sharpsma.com/webfm_send/1208

https://www.sparkfun.com/datasheets/Components/HMC6352.pdf

http://www.seeedstudio.com/wiki/Bluetooth_Bee

http://www.adafruit.com/product/746

@@ Line 1: / Line 1: @@
-=== Grading Criteria ===
+== '''Optimus Prime''': The Self-driving Car ==
-<font color="green">
+[[File:End_product.jpg|right|thumb|Optimus Prime]]
-*  How well is Software & Hardware Design described?
+Optimus Prime, the self-driving car is an autonomous driving vehicle which is capable of driving itself to its destination using GPS. While it does so, it also avoids obstacles using multiple sensors attached to it. It has an LCD screen to display the  useful information about the car in real time e.g. distance to the destination, speed, vehicle battery status, etc. The car can be controlled using an android app. This app was designed and developed specifically for this project. Using this app one can start and stop the car, increase or decrease the speed and set a destination to drive up to. This report is about designing and building this self governing car. This documentation is done keeping in mind the students who want to build their own self-driving car and for the curious ones who just want to know what goes inside an autonomous driving vehicle.
-*  How well can this report be used to reproduce this project?
-*  Code Quality
-*  Overall Report Quality:
-**  Software Block Diagrams
-**  Hardware Block Diagrams
-**:  Schematic Quality
-**  Quality of technical challenges and solutions adopted.
-</font>
-== Self Driving Car ==
+== '''Abstract''' ==
-A self governing car, capable of sensing its environment and navigating without human input. The car senses its surroundings and is capable of updating their maps based on sensory input, allowing the vehicle to keep track of its position.
+A self-driving car comprises of several controllers, each with a specific task dedicated to it. Our car consists of 6 such controllers. We have named them as Master, Motor, Sensor, GPS, Communication Bridge and I/O controllers. They communicate with each other over the CAN bus as shown in the diagram below. Each controller sends out the information over the CAN bus in the form of messages. Every controller receives only the required messages and performs the necessary task. The path navigation is achieved by the GPS. Thus the controllers do the task of a driver and navigate the path by avoiding the obstacles.The overall block diagram of the project is shown below. It includes all six controllers with their sensors  and actuators, communicating through a CAN bus.
-== Abstract ==
+{|
-This project is about developing a self driven car. It consists of 6 controllers - Master, Motor, Sensor, GPS, Communication Bridge and I/O, which communicate with each other over the CAN bus as shown below. Each controller sends out the information over the CAN bus in the form of messages. Every controller receives only the required messages and performs the necessary task. The path navigation is achieved by the GPS. Thus the controllers do the task of a driver and navigate the path by avoiding the obstacles.
+[[File:BlockDiagram.PNG|center|Project Block Diagram]]
-{| style="width:600px;" |
-[[File:CMPE243_Team2_OptimusPrime_Block_dia.jpg|600px|thumb|center|Block Diagram]]
 |}
-== Objectives & Introduction ==
+==== Parts List & Cost ====
-=== Team Members & Responsibilities ===
-*   Sensor Controller
-**  Team 1: Deepak Yadav & Vinod Pangul
-*   Motor Controller
-**  Team 2: Naghma Anwar & Shiva Moballegh
-*   I/O Unit
-**  Team 3: Shreeram Gopalakrishnan & Sreeharsha Paturu Gangadhara
-*   Communication Bridge & Android
-**  Team 4: Johnny Yam, Kevin Beadle & Chia Pin Tseng
-*   Geographical Controller
-**  Team 5: Bhushan Gopala Reddy, Ryan Marlin & Rishikesh Nagare
-*   Master Controller
-**  Team 6: Shashank Tupkar, Bhargava Leepeng Chandra & Preeti Benake
-=== Schedule ===
-'''Team Schedule'''
 {| class="wikitable"
 |-
-! scope="col"| Sl.No
+! scope="col"| Item#
-! scope="col"| Start Date
+! scope="col"| Part Desciption
-! scope="col"| End Date
+! scope="col"| Vendor
-! scope="col"| Task
+! scope="col"| Part Number
-! scope="col"| Status
+! scope="col"| Qty
-! scope="col"| Actual Completion Date
+! scope="col"| Cost
 |-
 ! scope="row"| 1
-|
+| RC Car
-|
+| Amazon.com
-| Order RC Car
+| Traxxas 37076 Rustler VXL
-| Completed on time
+| 1
-|
+| $380.57
 |-
 ! scope="row"| 2
-|
+| RC Car Battery
-|
+| Amazon.com
-| Order Other parts(Sensor/LCD/Motor Controller...)
+| Traxxas 2926 NiMH 8.4V Hump 3000mAh TRA Connector
-| Completed
+| 2
-|
+| $67.38
 |-
 ! scope="row"| 3
-| 9/30/2014
+| CAN Transceiver
-| 11/25/2014
+| Texas Instrument
-| Master Controller Team task
+| SN65HVD232D
-| Ongoing
+| 15
-|
+| $75.00
 |-
 ! scope="row"| 4
-| 10/06/2014
+| Assembly Components
-| 11/15/2014
+| Amazon.com, Anchor & HSC
-| Sensor Team task
+| PCBs, Mechnical & Electical Components
-| Completed
+| NA
-|
+| $110.80
 |-
 ! scope="row"| 5
-|
+| Power Supply
-|
+| Pololu.com
-| Motor Controller Team task
+| 6V Battery, 5V Regulator
-| Ongoing
+| 1
-|
+| $34.85
 |-
 ! scope="row"| 6
-|
+| Sonar sensor
-|
+| Maxbotix
-| Geographical Controller Team task
+| LV-MaxSonar-EZ1 MB1010
-| Ongoing
+| 3
-|
+| $99.55
 |-
 ! scope="row"| 7
-|
+| Sonar sensor
-|
+| Given by Preet
-| I/O Team task
+| LV-MaxSonar-EZ1 MB1010
-| Ongoing
+| 1
-|
+| Free
 |-
 ! scope="row"| 8
-|
+| Compass Module
-|
+| Given by Preet
-| Communication Bridge + Android Team task
+| HoneyWell: HMC 6352
-| Ongoing
+| 1
-|
+| Free
 |-
 ! scope="row"| 9
-|
+| LCD Display
-|
+| New Haven
-| Complete project integration
+| NHD-0216B3Z-FL-GBW-V3-ND
-| ???
+| 1
-|
+| $27.00
 |-
 ! scope="row"| 10
-|
+| Battery Status
-|
+| Amazon.com
-| Testing-1
+| Dc 4.0-30v LED Digital Display Voltage Meter
-| ???
+| 1
-|
+| $6.91
 |-
 ! scope="row"| 11
+| Bluetooth Bee
+| Amazon.com
+| B005GI4HFA
+| 1
+| $23.00
+|-
+! scope="row"| 12
+| Sensor RPM Long
+| Sheldon's Hobbies
+| Traxxas #6520
+| 1
+| $11.99
+|-
+! scope="row"| 13
+| Wire retainers/Gear Cover
+| Sheldon's Hobbies
+| Traxxas #6537
+| 1
+| $2.99
+|-
+! scope="row"| 14
+| Telemetry Trigger Magnet & Hold
+| Sheldon's Hobbies
+| Traxxas #6538
+| 1
+| $2.99
+|-
+! scope="row"| 15
+| Front Bumper & Screws
+| Sheldon's Hobbies
+| TRA2542
+| 1
+| $9.94
+|-
+! scope="row"|
+| Total Cost
+|
 |
-|
-| Testing-2
-| ???
 |
+| 849.13
+|-
 |}
+==== Team Schedule ====
-'''Master Controller Team Schedule'''
 {| class="wikitable"
 |-
-! scope="col"| Week No.
+! scope="col"| Sl.No
 ! scope="col"| Start Date
-! scope="col"| Planned End Date
+! scope="col"| End Date
 ! scope="col"| Task
 ! scope="col"| Status
-! scope="col"| Actual End Date
+! scope="col"| Actual Completion Date
 |-
 ! scope="row"| 1
-| 9/30/2014
+| 09/15/2014
-| 10/7/2014
+| 09/16/2014
-|
+| Order RC Car
- * Implement Basic CAN Hardware to communicate between 2 Controllers
+| Completed on time
-|
+| 09/20/2014
-* Completed
-: We are able to send a message from Tx over CAN and perform a specific operation at the Rx.
-| 10/7/2014
 |-
 ! scope="row"| 2
-| 10/7/2014
+| 09/15/2014
-| 10/14/2014
+| 09/16/2014
-|
+| Order Other parts(Sensor/LCD/Motor Controller...)
- * Design CAN Acceptance Filter among different Controllers
+| Completed
- * Define and Implement CAN Frame structure for proper communication
+| 09/20/2014
-   establishment
-|
-* Completed
-: Only messages with in range of acceptance filter are received, Decided on CAN frame structure using 11-bit frame.
-| 10/11/2014
 |-
 ! scope="row"| 3
-| 10/14/2014
+| 9/30/2014
-| 10/21/2014
+| 11/25/2014
-|
+| Master Controller Team task
- * Develop Inter-Controller Communication over CAN
+| Completed
- * Test point-to-point and Broadcast message transmission
+| 12/18/2014
- * Implement a Counter to count and display number of messages
-|
-* Completed
-: CAN Communication among multiple boards achieved, Point-to-Point & Broadcast modes are working, Able to display the count on 7-Seg Display on SJOne board.
-| 10/19/2014
 |-
 ! scope="row"| 4
-| 10/21/2014
+| 10/06/2014
-| 10/28/2014
+| 11/15/2014
-|
+| Sensor Team task
- * Layout blueprint for Controller and Module positioning
+| Completed
- * Assemble the RC Car with all the controllers and Modules
+| 11/15/2014
- * Define the Message List by working with other teams
+|-
- * Start working on CAN Periodic message structure
+! scope="row"| 5
-|
+| 9/30/2014
-* Completed
+| 10/20/2014
-: RC car design and module assembly is completed. Need some fine tuning for connections. Message list is generated and periodic message implementation started.
+| Motor Controller Team task
-| 10/28/2014
+| Completed
-|-
+| 11/25/2014
-! scope="row"| 5
-| 10/28/2014
-| 11/04/2014
-|
- * Complete CAN Periodic message structure to transmit Broadcast
-   messages over CAN and establish controlled communication among
-   different controllers
- * Implement Start condition detection and Fetch boot status from
-   all controllers and display the status of each controller
-|
-* Completed
-: Periodic Message Setup done. Able to receive boot status. Need to work on display of status.
-| 11/03/2014
 |-
 ! scope="row"| 6
-| 11/04/2014
+| 10/4/2014
-| 11/11/2014
+| 10/30/2014
-|
+| Geographical Controller Team task
- * Design 'Kill Switch' in co-ordination with Motor Controller team
+| Completed
-   and Bridge Controller team
+| 12/18/2014
- * Develop a 'CAN Bus Crash' detection and reset CAN Bus methodology
- * Design Automatic Head Light turn ON/OFF functionality by
-   working with Sensors Controller team
-|
-* Completed
-: Kill Switch implemented through Bridge controller. Head Lights implemented. LCD display of Status achieved.
-| 11/11/2014
 |-
 ! scope="row"| 7
-| 11/11/2014
+| 10/7/2014
-| 11/18/2014
+| 10/30/2014
-|
+| I/O Team task
- * Implement File Log saving to SD Card at periodic intervals
+| Completed
- * Work on Restoring to last known Status if the system crashes while running
+| 11/25/2014
- * Develop Detection technique if controllers are reaching 'Error State'
-|
-* Completed
-: File Log implemented. Error State is partially implemented. Obstacle detection achieved. Needed refinement in Direction control logic. Need to implement reverse logic.
-| 11/18/2014
 |-
 ! scope="row"| 8
-| 11/18/2014
+| 9/30/2014
-| 11/25/2014
+| 11/30/2014
-|
+| Communication Bridge + Android Team task
- * Project Integration and testing Basic Self_Drive Capability of the Car
+| Completed
- * Check the Functionality and behavior of all controllers in all the known
+| 11/30/2014
-   contexts
- * Perform modifications (if any) to eliminate any bugs to make the car work
-   seamlessly
- * Final Integration of car and testing there after
-|
-* Completed
-: Integration Started. Faced difficulty in synchronization.
-| 11/26/2014
 |-
 ! scope="row"| 9
-| 11/25/2014
+| 10/30/2014
-| 12/02/2014
+| 11/01/2014
-|
+| Complete project integration
- * Final Integration and testing Self_Drive Capability of the Car
+| Completed
-|
+| 11/30/2014
-* Ongoing
+|-
-| --/--/----
+! scope="row"| 10
+| 11/30/2014
+| 12/10/2014
+| Testing Phase-1
+| Completed
+| 12/10/2014
+|-
+! scope="row"| 11
+| 12/11/2014
+| 12/14/2014
+| Testing Phase-2
+| Completed
+| 12/14/2014
 |}
+== '''Introduction''' ==
+==== CAN Bus: A brief introduction ====
+Controller Area Network is a serial communication bus which allows microcontrollers to communicate with each other within a vehicle without a host computer. It uses differential transmission on a twisted pair wire which results in high immunity to electrical interference. Each microcontroller works as a node. There are several nodes that are connected to each other through a CAN bus. Each node is able to send and receive messages, but not simultaneously. There is an arbitration scheme which works on message priority. Each microcontroller has its own message ID. Lower message ID represents higher message priority. To learn more about CAN bus communication, visit the following wikipage article.
+* [[CAN BUS Tutorial]]
+==== The Six Controllers ====
+* [[#Master Controller|''Master Controller'']]
+* [[#Motor Controller|''Motor Controller'']]
+* [[#Sensor Controller|''Sensor Controller'']]
+* [[#Geographical Controller|''Geographical Controller'']]
+* [[#Android & Communication Bridge Controller|''Android & Communication Bridge Controller'']]
+* [[#I/O Unit Controller|''I/O Unit Controller'']]
+== '''Design & Implementation''' ==
+==== Controller Communication Table ====
-'''Sensor Team Schedule'''
 {| class="wikitable"
+|+ Controllers
 |-
-! scope="col"| Sl.No
+| Controller ID
-! scope="col"| Start Date
+| Controller Type
-! scope="col"| End Date
-! scope="col"| Task
-! scope="col"| Status
-! scope="col"| Actual Completion Date
 |-
-! scope="row"| 1
+| 0x01
-| 10/6/2014
+| Master Controller
-| 10/18/2014
-| Order Ultra Sonic Sensors
-| Completed [Got two sensors (front and back), 2 more (front right & left) to order ->Completed.]
-| 10/19/2014
 |-
-! scope="row"| 2
+| 0x02
-| 10/9/2014
+| Motor Controller
-| 10/9/2014
+|-
-| Sensor Data Sheet review with the team
+| 0x03
-| Completed
+| Sensor Controller
-| 10/9/2014
 |-
-! scope="row"| 3
+| 0x04
-| 10/9/2014
+| Geographical Controller
-| 10/16/2104
-| Sensor code development
-| Completed (Implementing filter (HW/SW) to get more accurate data ->(Done). Add logic to get the rest of the three sensor(front right/left and back data)->(Done) (Note: Delayed due to the implementation of CAN structure and calibration of IR sensor)
-| 10/21/2014
 |-
-! scope="row"| 4
+| 0x05
-| 10/22/2014
+| IO Controller
-| 10/25/2014
-| Sensor software testing
-| Ongoing
-|
 |-
-! scope="row"| 5
+| 0x06
-| 10/25/2014
+| Bridge Controller
-| 10/28/2014
+|}
-| Sensor real time testing
-| Ongoing
+{| class="wikitable"
-|
+|+ Common Communication Table
 |-
-! scope="row"| 6
+| Message Number
-| 10/13/2014
+| Purpose / Data layout
-| 10/15/2014
-| Light sensor code Development
-| Completed
-| 10/14/2014
 |-
-! scope="row"| 7
+| 0x101
-| 10/13/2014
+| Get version and boot info
-| 10/15/2014
-| Accelerometer sensor code Development to detect tilt
-| Completed
-| 10/14/2014
 |-
-! scope="row"| 8
+| 0x102
-| 10/15/2014
+| Get general info
-| 10/15/2014
-| Light Sensor and Accelerometer Testing
-| Completed
-| 10/15/2014
 |-
-! scope="row"| 9
+| 0x103
-| 10/29/2014
+| Synchronize (set) time:
-| 10/31/2014
+ byte [0-3] : System time
-| Battery status controller circuit Design
-| Ongoing
-|
 |-
-! scope="row"| 10
+| 0x201
-| 11/01/2014
+|
-| 11/02/2014
+ byte [0-3] : Version Info
-| Battery status-circuit Testing
+ byte [4-7] : boot timestamp
-|
-|
 |-
-! scope="row"| 11
+| 0x202
-| 11/03/2014
+|
-| 11/04/2014
+ byte [0-3] : Current time
-| Common Communication SW code implementation and testing
+ byte [4]   : CPU usage %
-|
-|
-|-
-! scope="row"| 11
-| 11/04/2014
-| 11/09/2014
-| Complete Hardware testing-1
-|
-|
-|-
-! scope="row"| 12
-| 11/10/2014
-| 11/15/2014
-| Complete Hardware testing-2
-|
-|
 |}
-'''Motor Controller Team Schedule'''
 {| class="wikitable"
+|+ Subscription Rate Info
 |-
-! scope="col"| Week No.
+| Byte 0
-! scope="col"| Start Date
+| Effect
-! scope="col"| Planned End Date
+|-
-! scope="col"| Task
+| 0
-! scope="col"| Status
+| Off
-! scope="col"| Actual End Date
 |-
-! scope="row"| 1
+| 1
-| 9/30/2014
+| 1Hz
-| 10/7/2014
-|
- * Study SJOne board's motor controller concepts and PWM
-|
-* Completed
-: Very simple code. Just two lines. Set the frequency. Set the duty cycle.
-| 10/7/2014
 |-
-! scope="row"| 2
+| 5
-| 10/7/2014
+| 5Hz
-| 10/14/2014
-|
- * Open up RC Car's motor and servo connections
- * Study the Electronic Speed Control's functions
-|
-* Completed
-: Motor and Servo operate on the same frequency
-: ESC needs calibration each time it is switched on. Need to find a solution for this.
-| 10/11/2014
 |-
-! scope="row"| 3
+| 10
-| 10/14/2014
+| 10Hz
-| 10/21/2014
+|-
-|
+| 20
- * Define the duty cycles for proper motor and servo signals
+| 20Hz
-|
-* Completed
-: Using trial and error, figured out the duty cycle for constant speed and turns
-| 10/19/2014
 |-
-! scope="row"| 4
+| 50
-| 10/21/2014
+| 50Hz
-| 10/28/2014
-|
- * Add CAN frame structure to the motor functions
- * Test for communication between motors and sensors for prototype demo
- * Define the Message List by working with other teams
-|
-* Completed
-| 11/04/2014
 |-
-! scope="row"| 5
+| Any other value
-| 10/28/2014
+| Invalid date rate
-| 11/04/2014
+|}
-|
-  * Start working on CAN Periodic message structure
+== '''Master Controller''' ==
- * Start looking for speed sensors
+==== Group Members ====
+ '''''Bhargava Leepeng Chandra'''''
+ '''''Preeti Benake'''''
+==== Description ====
+Master controller acts as the 'Brain' of the car. It communicates with all the other Controllers on board to implement different Functions. Being the Brain it intelligently processes the data it receives from Sensor, GPS and Bridge controllers to make the car run autonomously. It has several features embedded in it, and controls the car by sending commands to the Motor Controller. In short the master controller actively Receives, Processes and Transmits real-time data.
+==== Master Controller Team Schedule ====
+{| class="wikitable"
+|-
+! scope="col"| Week No.
+! scope="col"| Start Date
+! scope="col"| Planned End Date
+! scope="col"| Task
+! scope="col"| Status
+! scope="col"| Actual End Date
+|-
+! scope="row"| 1
+| 9/30/2014
+| 10/7/2014
+|
+  * Implement Basic CAN Hardware to communicate between 2 Controllers
 |
 * Completed
-: Bought magnetic speed sensor from Traxxas telemetry
+: We are able to send a message from Tx over CAN and perform a specific operation at the Rx.
-: from local RC Car store
+| 10/7/2014
-| 11/04/2014
 |-
-! scope="row"| 6
+! scope="row"| 2
-| 11/04/2014
+| 10/7/2014
-| 11/11/2014
+| 10/14/2014
 |
-  * Attach speed sensors to the motor
+  * Design CAN Acceptance Filter among different Controllers
-  * Test CAN communication between motor controller and other controllers
+  * Define and Implement CAN Frame structure for proper communication
+   establishment
 |
 * Completed
-: Speed sensors attached
+: Only messages with in range of acceptance filter are received, Decided on CAN frame structure using 11-bit frame.
-| 11/11/2014
+| 10/11/2014
 |-
-! scope="row"| 7
+! scope="row"| 3
-| 11/11/2014
+| 10/14/2014
-| 11/18/2014
+| 10/21/2014
 |
-  * Work on speed sensors. Figure out the way to send sensor data to master controller.
+  * Develop Inter-Controller Communication over CAN
-  * Test for proper and accurate CAN communication
+ * Test point-to-point and Broadcast message transmission
+  * Implement a Counter to count and display number of messages
 |
 * Completed
-| 11/18/2014
+: CAN Communication among multiple boards achieved, Point-to-Point & Broadcast modes are working, Able to display the count on 7-Seg Display on SJOne board.
+| 10/19/2014
 |-
-! scope="row"| 8
+! scope="row"| 4
-| 11/18/2014
+| 10/21/2014
-| 11/25/2014
+| 10/28/2014
 |
-  * Project Integration and testing basic self drive capability of the car
+  * Layout blueprint for Controller and Module positioning
-  * Check the functionality and behavior of the motor controller in all the known
+  * Assemble the RC Car with all the controllers and Modules
-   contexts
+  * Define the Message List by working with other teams
-  * Perform modifications (if any) to eliminate any bugs to make the motor work
+  * Start working on CAN Periodic message structure
-   seamlessly
-  * Final Integration of car and testing there after
 |
-* Ongoing
+* Completed
-| --/--/----
+: RC car design and module assembly is completed. Need some fine tuning for connections. Message list is generated and periodic message implementation started.
+| 10/28/2014
-|}
-'''Geographical Team Schedule'''
-{| class="wikitable"
 |-
-! scope="col"| Sl.No
+! scope="row"| 5
-! scope="col"| Start Date
+| 10/28/2014
-! scope="col"| End Date
+| 11/04/2014
-! scope="col"| Task
+|
-! scope="col"| Status
+ * Complete CAN Periodic message structure to transmit Broadcast
-! scope="col"| Actual Completion Date
+   messages over CAN and establish controlled communication among
+   different controllers
+ * Implement Start condition detection and Fetch boot status from
+   all controllers and display the status of each controller
+|
+* Completed
+: Periodic Message Setup done. Able to receive boot status. Need to work on display of status.
+| 11/03/2014
 |-
-! scope="row"| 1
+! scope="row"| 6
-| 10/4/2014
+| 11/04/2014
-| 10/13/2014
-| Research and Order GPS module
-| Received GPS module
-| 10/7/2014
-|-
-! scope="row"| 2
-| 10/7/2014
-| 10/18/2014
-| Interface GPS module with LPC1758
-| Finished
-| 10/17/14
-|-
-! scope="row"| 3
-| 10/14/2014
-| 10/18/2014
-| Receive Compass module from Preet
-| Received
-| 10/9/2014
-|-
-! scope="row"| 4
-| 10/18/2014
-| 11/4/2014
-| Parse GPS data and setup constructs to send appropriate data
-| Ongoing
-| |
-|-
-! scope="row"| 5
-| 10/14/2014
-| 10/18/2014
-| Interface the Compass Module
-| Finished
-| 10/16/2014
-|-
-! scope="row"| 6
-| 10/25/2014
-| 11/4/2014
-| Calibration of Compass
-| Code completed. Need to test using the car
-| --/--/----
-|-
-! scope="row"| 7
-| 11/4/2014
 | 11/11/2014
-| Integrate GPS and Compass data
-| Ongoing
 |
+ * Design 'Kill Switch' in co-ordination with Motor Controller team
+   and Bridge Controller team
+ * Develop a 'CAN Bus Crash' detection and reset CAN Bus methodology
+ * Design Automatic Head Light turn ON/OFF functionality by
+   working with Sensors Controller team
+|
+* Completed
+: Kill Switch implemented through Bridge controller. Head Lights implemented. LCD display of Status achieved.
+| 11/11/2014
 |-
-! scope="row"| 8
+! scope="row"| 7
-| 10/25/2014
+| 11/11/2014
-| 11/09/2014
-| Testing and mapping of GPS co-ordinates
-| Ongoing
-|
-|-
-! scope="row"| 9
 | 11/18/2014
-| 11/25/2014
-| Final integration and testing
 |
+ * Implement File Log saving to SD Card at periodic intervals
+ * Work on Restoring to last known Status if the system crashes while running
+ * Develop Detection technique if controllers are reaching 'Error State'
 |
-|}
+* Completed
+: File Log implemented. Error State is partially implemented. Obstacle detection achieved. Needed refinement in Direction control logic. Need to implement reverse logic.
-'''IO Team Schedule'''
+| 11/18/2014
-{| class="wikitable"
 |-
-! scope="col"| Sl.No
+! scope="row"| 8
-! scope="col"| Start Date
+| 11/18/2014
-! scope="col"| End Date
+| 11/25/2014
-! scope="col"| Task
+|
-! scope="col"| Status
+ * Project Integration and testing Basic Self_Drive Capability of the Car
-! scope="col"| Actual Completion Date
+ * Check the Functionality and behavior of all controllers in all the known
+   contexts
+ * Perform modifications (if any) to eliminate any bugs to make the car work
+   seamlessly
+ * Final Integration of car and testing there after
+|
+* Completed
+: Integration Started. Faced difficulty in synchronization.
+| 11/26/2014
 |-
-! scope="row"| 1
+! scope="row"| 9
-| 10/7/2014
+| 11/25/2014
-| 10/13/2014
+| 12/02/2014
-| Research and Order LCD Display
+|
-| Ordered LCD Display
+ * Final Integration and testing Self_Drive Capability of the Car
-| 10/13/2014
+|
+* completed
+: We are able to integrate all the different on-board systems and control the features with the master's control algorithm using real-time data from Sensor, Geo and Bridge controllers. The primary objective of self-drive capability is achieved. We have faced little difficulty in adjusting the frequency of data appropriate to real time needs.
+| 12/8/2014
 |-
-! scope="row"| 2
+! scope="row"| 10
-| 10/14/2014
+| 12/02/2014
-| 10/21/2014
+| 12/18/2014
-| Interfacing LCD Display with LPC1758
+|
-| Completed
+ * Final Testing with all Features
-| 10/21/2014
+|
+* completed
+: Checked out the Data Log for any possible message drops. Resolved issues related to Compass.
+| 12/15/2014
 |-
-! scope="row"| 3
+|}
-| 10/21/2014
-| 10/28/2014
+==== Hardware Design ====
-| Implementing CAN structure with LCD tasks.
+* An RC car was used as a base to demonstrate the Self-Driven Capability of a car with all the Controlling done by SJOne boards.
-| Completed
+* The hardware for this Project is custom designed according to the requirements of the project.
-| 11/30/2014
+* This includes building the Chassis to place all the SJOne boards.
+* Sufficient Power and Ground slots for all the Sensors, GPS, Compass, LCD breakout boards.
+* Designing a CAN bus structure for establishing communication among different SJOne boards.
+* Designing a Spike protection for the Input power supply.
+* Finally Sufficient number of pins(if necessary) to connect external Breakout boards to the SJOne controllers.
+==== Hardware Implementation ====
+* First we have started by designing the chassis using a PCB as base to place all the SJOne boards that represents the 6 sub-teams,this includes a separate base for placing LCD module, Head-lights and Tail-lamps.
+* As a second step we moved forward by designing the circuitry for Power Supply and Spike protection by designing a 5V voltage regulator, that serves as a power supply to all the SJOne controllers and LCD module.
+* Then sufficient VCC and GND slots were added to the PCB that could accommodate Sonar sensors, GPS and Compass modules, Head-lights and Tail-lamps.
+* Later a common CAN bus structure was designed to support the CAN transceivers for each individual SJOne board. The entire system is built around this CAN structure.
+* Then the Hardware was made robust enough to take all the hits during the testing process.
+Following is the top view of the car showing the connection of all the 6 controllers and the hardware interfaced to each of them.
+[[File: Cmpe243_team3_Block.JPG|600px|center]]
+==== Hardware Challenges and Difficulties ====
+* The major challenge is to design a common CAN bus structure. One need to understand the electrical characterisitcs of CAN in order to design it better. We had to go through several debugging stages to evaluate the perfromance of the CAN bus as it used to fail at times.
+* Care must be taken in designing the connections for CAN-HIGH and CAN_LOW. The supply for each CAN needed to be separate in our case in order to provide sufficient drive current to the CAN transceiver.
+* Next to this another challenge was to make the Hardware robust. During the testing phase it takes a lot of hits and bangs, the module fitting and the circuitary needs to be good enough to absorb all the pressure. By reducing the number of wired connections the robability of hardware fails can be reduced.
+* Another difficulty was to supply PWM signals to the Motor. The Signals should be strong enough to run the DC motor and Servo motor of the car. It happened to be that if the trace/wire connection is too long the PWM signal is losing its strength. So it should be as much near to the motor as possible.
+* The positioning of the Sonar sensors should be appropriate to avoid any bounce off, To deal with the bouncing effect we should place it at some height/angular height to reduce the possiblity of bouncing from the ground. Also each sensor should be at a distance and angle with respect to other sensors to facilitate sufficient area of detection.
+* The positioning of Compass module is a little bit tricky. This should be far away from Electrical/Magnetic interferences as it very sensitive to these effects. So we placed it on the top at a height to avoid any corrupted values.
+==== Hardware Interface ====
+{| style="width:800px;" |
+|[[File:CMPE_TEAM3_Master_block.jpg|800px|thumb|Block diagram of Master controller ]]
+|}
+{| class="wikitable"
+|+ Master Controller Pin Connectivity Table
+|-
+! scope="col"| '''Description'''
+! scope="col"| '''Your Device Port'''
+! scope="col"| '''SJOne Development Board Port'''
 |-
-! scope="row"| 4
+| Supply Voltage
-| 10/28/2014
+| Supply +5V
-| 11/04/2014
+| Board +5V
-| Subscribe data from motor, sensor and GPS controller,display it on LCD.
-| Ongoing
-|
 |-
-! scope="row"| 5
+| Ground
-| 11/04/2014
+| Supply GND
-| 11/11/2014
+| Board GND
-| Setup hardware and write code for START, STOP and Headlight buttons.
-| TBD
-|
 |-
-! scope="row"| 6
+| CAN Transceiver
-| 11/11/2014
+| Pin no. 1 Driver Input
-| 11/18/2014
+Pin no. 4 Receiver Output
-| Testing and mounting hardware on car.
+| P0.1 CAN TD1
-| TBD
+P0.0 CAN RD1
-|
+|-
+| Head Lights
+| LED +3.3V
+LED GND
+| Pin 1.20, 1.22 GPIO
+Common GND
+|-
+| LED Strip
+| LED Strip DIN
+LED Strip +5V
+LED Strip GND
+| Pin 1.29 GPIO
+Common VCC
+Common GND
 |-
-! scope="row"| 7
-| 11/18/2014
-| 11/25/2014
-| Final Testing
-| TBD
-|
 |}
+==== Software Design ====
+* Master controller which is the central controller, performs all its functions with FreeRTOS software running at its core.
+* The two key components of FreeRTOS utilized by Master to achieve these operations are
+: 1. FreeRTOS Task and Scheduler
+: 2. FreeRTOS Queues
+* Master controller heavily rely on the FreeRTOS scheduler, for most of the time to run various tasks, which are responsible for what the master controller does.
+* The FreeRTOS queue structure is used to achieve inter-task communication inside the Master controller to process data and transmit to respective controllers.
+* CAN bus structure with 29 bit message ids is used to establish communication among different controllers. The Broadcast bus made point to point to exchange data between any two controllers by configuring an additional Acceptance filter.
+* The periodic CAN message structure provided by Preet helps transmit specific data to specified destination at a specified interval like 1Hz, 5Hz, 10Hz etc.
+* The File logger task runs along with other tasks to log real time data onto SD card in order to facilitate debugging without sacrificing the speed for debugging.
+* Additional features like Light sensor controlled Head Lights are implemented to make the car feasible for low light/night time runs.
+* Apart form this an LED strip is used to indicate when the car is being run on sensor's data, when an obstacle is detected. This distinctively demonstrates when the car is controlled by a particular controller among the Geographical controller and Sensor controller.
-'''Communication Bridge & Android Team Schedule'''
+==== Software Implementation ====
+* The implementation of the specified software design for master controller is achieved by using the FreeRTOS and CAN libraries provided by Preet.
+* The Master operation starts with the initilization of CAN Bus and configuring the CAN acceptance filter. The sample code is shown below.
-{| class="wikitable"
-|-
+[[File: CmpE243_F14_T3_CAN_INIT.PNG | center]]
-! scope="col"| Sl.No
-! scope="col"| Start Date
-! scope="col"| Planned End Date
+* In main the control next creates new tasks like Receive task to deal with different functions, which will only start running after the scheduler.
-! scope="col"| Task
+*These tasks supply Data to periodic tasks next in the line to Transmit data over the CAN bus to the specified destination.
-! scope="col"| Status
-! scope="col"| Actual End Date
+[[File: CmpE243_F14_T3_Tasks.PNG‎ | center]]
+[[File: CmpE243_F14_T3_Periodic.PNG |center]]
+* The FreeRTOS queues exchange data among different tasks to process the data. This comprises data from Sensors, Geo and Bridge Controllers.
+* The Processed data put into the Decision making algorithm performs direction and speed controlling operations.
+The software design and implementation of the master controller is explained by the flowchart.
+[[file: CMPE243_Master_1.jpg | left]]
+==== Implementation ====
+{| class="wikitable"
+|+ Master Controller Communication Table
 |-
-! scope="row"| 1
+| Message Number
-| 9/30/2014
+| Purpose
-| 9/30/2014
+| Data Byte Pattern
-| Obtain Bluetooth Module (already had one)
-| Done
-| 9/30/2014
 |-
-! scope="row"| 2
+| 0x101
-| 9/30/2014
+| Ask for Boot and Version Info. of all Controllers
-| 10/14/2014
+|
-| Develop Basic Android App with Bluetooth Sensor Communication
+ Byte[0]: Send a '1'
-| Done
+|
-| 10/7/2014
+|-
+| 0x103
+| Sync. Master System Time on all Controllers
+|
+ Byte[0-3]: System Time [HH:MM:SS]
+|
 |-
-! scope="row"| 3
+| 0x201
-| 10/11/2014
+| Master Gets Status Update from all controllers
-| 10/14/2014
+|
-| Interface Bluetooth Module with SJSU Dev Board
+ Byte[0]: Boot Status
-| Done
+ Byte[1]: Version Info.
-| 10/11/2014
+|
 |-
-! scope="row"| 4
+| 0x203
-| 10/12/2014
+| Master Gets current Time from all Controllers
-| 10/19/2014
+|
-| Be able to send bi-directional arbitrary messages between Android App and Dev Board via Bluetooth
+ Byte[0-3]: Time in [HH:MM:SS]
-| Done
+|
-| 10/14/2014
 |-
-! scope="row"| 5
+| 0x301
-| 10/14/2014
+| Master Enable Main UI in Android
-| 11/21/2014
+|
-| Subscribe to all CAN messages and dump all of them via Bluetooth to Android App or web interface
+ Byte[0]: Send a '1'
-| Done
+|
-| 11/24/2014
 |-
-! scope="row"| 6
+| 0x302
-| 10/14/2014
+| Master set GPS Destination on Geo Controller
-| 11/21/2014
+|
-| Ajax & Websocket server remote structure
+ Byte[0-3]: Latitude Value
-| Done
+ Byte[4-7]: Longitude Value
-| 11/01/2014
+|
 |-
-! scope="row"| 7
+| 0x303
-| 10/14/2014
+| Master set Longitude Way-Points on Geo
-| 11/21/2014
+|
-| Be able to input GPS coordinates through either (or both) Android App and web interface and send through Bluetooth then CAN bus
+ bytes [0-1] : Total Way-Points count
-| Done
+ bytes [2-3] : Way-Point index
-| 11/24/2014
+ bytes [4-7] : Longitude(float)
+|
 |-
-! scope="row"| 8
+| 0x304
-| 10/21/2014
+| Master set Latitude Way-Points on Geo
-| 11/24/2014
+|
-| Android App and webpage GUI enhancements (Google Maps, Google Drive)
+ bytes [0-1] : Total Way-Points count
-| Done
+ bytes [2-3] : Way-Point index
-| 11/24/2014
+ bytes [4-7] : Latitude(float)
+|
 |-
-! scope="row"| 9
+| 0x305
-| 10/21/2014
+| Master Send GPS FIX Ack to Bridge
-| 11/30/2014
+|
-| Data visualization (status, compass, speed, location,....)
+ Byte[0]: Send a value '1'
-| On going
+|
-| TBD
-|}
-== Parts List & Cost ==
-{| class="wikitable"
 |-
-! scope="col"| Item#
+| 0x306
-! scope="col"| Part Desciption
+| Master Send Dest. Reached Ack to Bridge
-! scope="col"| Vendor
+|
-! scope="col"| Part Number
+ Byte[0]: Send a Value '1'
-! scope="col"| Qty
+|
-! scope="col"| Cost
 |-
-! scope="row"| 1
+| 0x500
-| RC Car
+| Display Boot and Version Info. on LCD
-| Amazon.com
+|
-| Traxxas 37076 Rustler VXL
+ Byte[0]: Boot Status Response
-| 1
+ Byte[1]: Version Info.
-| $380.57
+|
 |-
-! scope="row"| 2
+| 0x501
-| RC Car Battery
+| Display Controllers Time on LCD
-| Amazon.com
+|
-| Traxxas 2926 NiMH 8.4V Hump 3000mAh TRA Connector
+ Byte[0-3]: Time in [HH:MM:SS]
-| 2
+|
-| $67.38
 |-
-! scope="row"| 3
+| 0x502
-| CAN Transceiver
+| Display Destination Has Reached
-| Texas Instrument
+|
-| SN65HVD232D
+ Byte[0]: Send a '1'
-| 15
+|
-| $75.00
 |-
-! scope="row"| 4
+| 0x503
-| Assembly Components
+| Master Set Speed and Direction of Motor
-| Amazon.com, Anchor & HSC
+|
-| PCBs, Mechnical & Electical Components
+ Byte[0]: LEFT/RIGHT (or) FRONT/BACK command
-| NA
+|
-| $110.80
 |-
-! scope="row"| 5
+| 0x504
-| Power Supply
+| Display Speed of Motor on LCD
-| Pololu.com
+|
-| 6V Battery, 5V Regulator
+ Byte[0]: Speed Value
-| 1
+|
-| $34.85
 |-
-! scope="row"| 6
+| 0x505
-| Sonar sensor
+| Display GPS and Compass values on LCD
-| Maxbotix
+|
-| LV-MaxSonar-EZ1 MB1010
+ Byte[0-1]: New Degree to Head
-| 3
+ Byte[2-3]: Dist to Destination
-| $99.55
+ Byte[4-5]: Current Degree value
+|
 |-
-! scope="row"| 7
+|0x506
-| Sonar sensor
+| Display Sensor Values on LCD
-| Given by Preet
+|
-| LV-MaxSonar-EZ1 MB1010
+ Byte [0]: Front sensor value in inches
-| 1
+ Byte [1]: Front Left sensor value in inches
-| Free
+ Byte [2]: Front Right sensor value in inches
+ Byte [3]: Back sensor value in inches
+|
+|-
+|0x507
+| Display Battery Status on LCD
+|
+ Byte[0]: Battery Status Value
+|
 |-
-! scope="row"| 8
+|0x540
-| Compass Module
+| Send GPS Data to Bridge
-| Given by Preet
+|
-| HoneyWell: HMC 6352
+ Byte[0-1]: Heading Degree
-| 1
+ Byte[2-3]: Dist. to Destination
-| Free
+ Byte[4-5]: Current Bearing Degree
+ Byte[6-7]: Difference between Heading and Bearing angle
+|
 |-
-! scope="row"| 9
+|0x550
-| LCD Display
+| Send Sensor Data to Bridge
-| New Haven
+|
-| NHD-0216B3Z-FL-GBW-V3-ND
+ Byte[0]: Front Sensor
-| 1
+ Byte[1]: Front Right Sensor
-| $$$.$$
+ Byte[2]: Front Left Sensor
-|-
+ Byte[3]: Back Sensor
-! scope="row"| 10
+  Byte[4]: Speed value
-| Battery Status
-| Amazon.com
-| Dc 4.0-30v LED Digital Display Voltage Meter
-| 1
-| $6.91
-|-
-! scope="row"|
-| Total Cost
-|
-|
 |
-| $$$.$$
 |-
 |}
-== Design & Implementation ==
+==== Testing and Technical Challenge ====
-=== Controller Communication Table ===
+We have faced several Difficulties during Software design implementation for Master Controller. Some of these issues are discussed here.
+* Top of the list is the Integration. We have faced difficulty in achieving the integration of all the individual controllers working together in synchronization with each other.
+* Another issue is the CAN bus communication failure which is due to improper transmitting formats like message ID duplication causing the CAN bus error. There are also issues due to improper configuration of acceptance filter, which is later resolved.
+* We have also faced difficulty when using the FreeRTOS queues, This is caused due to using a particular queue at some locations before it is actually declared declared.
+* Apart from this the Queue timing implementation has to be observed carefully as it may conflict the frequency of real time Data that causes error status as the receiving queue task cannot see any data on the queue.
+* We have faced difficulty in data synchronization during testing. The real-time data needs forced us to modify the Transmitting frequencies from certain controllers, particularly for Geographical controller.
+== '''Motor Controller''' ==
+==== Group Members ====
+ '''''Shashank Tupkar'''''
+ '''''Naghma Anwar'''''
+ '''''Shiva Moballegh'''''
+==== Motor Controller Team Schedule ====
 {| class="wikitable"
-|+ Controllers
 |-
-| Controller ID
+! scope="col"| Week No.
-| Controller Type
+! scope="col"| Start Date
+! scope="col"| Planned End Date
+! scope="col"| Task
+! scope="col"| Status
+! scope="col"| Actual End Date
 |-
-| 0x01
+! scope="row"| 1
-| Master Controller
+| 9/30/2014
+| 10/7/2014
+|
+* Study SJOne board's motor controller concepts and PWM
+|
+* Completed
+: Very simple code. Just two lines. Set the frequency. Set the duty cycle.
+| 10/7/2014
 |-
-| 0x02
+! scope="row"| 2
-| Motor Controller
+| 10/7/2014
+| 10/14/2014
+|
+* Open up RC Car's motor and servo connections
+* Study the Electronic Speed Control's functions
+|
+* Completed
+: Motor and Servo operate on the same frequency
+: ESC needs calibration each time it is switched on. Need to find a solution for this.
+| 10/11/2014
 |-
-| 0x03
+! scope="row"| 3
-| Sensor Controller
+| 10/14/2014
+| 10/21/2014
+|
+* Define the duty cycles for proper motor and servo signals
+|
+* Completed
+: Using trial and error, figured out the duty cycle for constant speed and turns
+| 10/19/2014
 |-
-| 0x04
+! scope="row"| 4
-| Geographical Controller
+| 10/21/2014
+| 10/28/2014
+|
+* Add CAN frame structure to the motor functions
+* Test for communication between motors and sensors for prototype demo
+* Define the Message List by working with other teams
+|
+* Completed
+| 11/04/2014
 |-
-| 0x05
+! scope="row"| 5
-| IO Controller
+| 10/28/2014
+| 11/04/2014
+|
+* Start working on CAN Periodic message structure
+* Start looking for speed sensors
+|
+* Completed
+: Bought magnetic speed sensor from Traxxas telemetry
+: from local RC Car store
+| 11/04/2014
 |-
-| 0x06
+! scope="row"| 6
-| Bridge Controller
+| 11/04/2014
-|}
+| 11/11/2014
+|
-{| class="wikitable"
+* Attach speed sensors to the motor
-|+ Common Communication Table
+* Test CAN communication between motor controller and other controllers
+|
+* Completed
+: Speed sensors attached
+| 11/11/2014
 |-
-| Message Number
+! scope="row"| 7
-| Purpose / Data layout
+| 11/11/2014
+| 11/18/2014
+|
+* Work on speed sensors. Figure out the way to send sensor data to master controller.
+* Test for proper and accurate CAN communication
+|
+* Completed
+| 11/18/2014
 |-
-| 0x101
+! scope="row"| 8
-| Get version and boot info
+| 11/18/2014
-|-
+| 11/25/2014
-| 0x102
-| Get general info
-|-
-| 0x103
-| Synchronize (set) time:
- byte [0-3] : System time
-|-
-| 0x201
 |
- byte [0-3] : Version Info
+* Project Integration and testing basic self drive capability of the car
- byte [4-7] : boot timestamp
+* Check the functionality and behavior of the motor controller in all the known contexts
-|-
+* Perform modifications (if any) to eliminate any bugs to make the motor work seamlessly
-| 0x202
+* Final Integration of car and testing there after
 |
- byte [0-3] : Current time
+* Completed
- byte [4]   : CPU usage %
+| 12/12/2014
 |}
-{| class="wikitable"
+==== Hardware Design ====
-|+ Subscription Rate Info
+[[File:CmpE243_F14_T3_Hardware.png|Anatomy of The Rustler]]
-|-
+===== Parts and their functions =====
-| Byte 0
+[[File:CmpE243_F14_T3_Motor.png|thumb|right|Velineon 3500 Brushless Motor]]
-| Effect
+'''''Motor''''' : Our RC car came with Velineon 3500 Brushless Motor. One of the main drawbacks of brushless motor is that it requires a speed controller to change the field polarity. We can't just give power to the motor directly and expect it to go. We can almost consider the controller as an integral part of the motor itself.
+[[File:CmpE243_F14_T3_ESC.png|thumb|left|Velineon VXL-3s ESC]]
+'''''ESC''''' : Electronic speed controller was the trickiest part to deal with, since it comes with a previously programmed microcontroller inside it. It needs callibration, for which you need to refer to the user manual. An electronic speed controller basically controls the power given to the motor. Our RC car came with VXL-3s ESC, which accepted 100 Hz PWM input signal whose duty cycle varied from 10% to 20%. When supplied with a 15% duty cycle at 100 Hz, the ESC responded by turning off the motor attached to its output.
+'''''Steering Servo''''' : Our RC car was equipped with a digital servo (Traxxas part #2075) for steering control. It does not require an ESC to operate. We can give PWM signal directly to the servo from the SJOne board. The servo accepted 100 Hz PWM input signal whose duty cycle varied from 10% to 20%, where 10% represents extreme right turn and 20% represents extreme left turn.[[File:CmpE243_F14_T3_Servo.jpg|thumb|right|Steering Servo]]
+'''''Speed Sensor''''' : To measure the RPM and speed of our car, we used the speed sensor provided by Traxxas Telemetry. This magnetic speed sensor worked on Hall effect. To learn more about Hall effect sensors, you can click on this [http://en.wikipedia.org/wiki/Hall_effect_sensor wikipedia article]. Since the sensor was provided by the same brand of our car, the installation was quick and easy. Here's a reference [https://www.youtube.com/watch?v=xx-Ft_kzTzs video] on how to attach magnetic speed sensor to the RC car.
+[[File:CmpE243_F14_T3_Battery.jpg|thumb|left|Traxxas 7-Cell 8.4V NiMH Battery Pack]]
+'''''Battery''''' : We used 7 Cell NiMH (Nickel-Metal Hydride) battery pack for our car but would recommend others to use Lipo (Lithium Polymer) batteries instead. NiMH batteries tend to discharge very quickly. Also we realized later that since this car was made for racing purpose, its speed was too fast for our project. We reduced the voltage by removing 2 cells from the 7 cell battery pack. So, go for the 5 cell battery pack instead. A Traxxas EZ-Peak Charger would help a lot while doing testing.
+'''''Gears''''' : Gears also play an important role in determining the Speed of the car. A gear is defined by the number of Cogs (teeth) which determines if the gear increases (or) decreases the output speed delivered to the axle. So, we can also opt for different gears to reduce the overall speed in any case necessary. In our case changing the gears isn't an option since our car is set with the minimum gear as it belongs to sports car category. But however some custom gears can still do the job in reducing the unnecessary speed, though they are a little bit hard to get our hands on it.
+==== Hardware Interface ====
+===== Motor, Servo and Speed Sensor Interface =====
+[[File:CmpE243_F14_T3_PinConnection.png]]
+{| class="wikitable"
+|+ Motor Controller Pin Connectivity Table
 |-
-| 0
+! scope="col"| '''Description'''
-| Off
+! scope="col"| '''Your Device Port'''
+! scope="col"| '''SJOne Development Board Port'''
+! scope="col"| '''Commands'''
+! scope="col"| '''Note'''
 |-
-| 1
+| Supply Voltage
-| 1Hz
+| 6V from NiMH battery
-|-
+| N/A
-| 5
+|
-| 5Hz
+|
 |-
-| 10
+| Ground
-| 10Hz
+| GND (Black Wire)
+| GND
+|
+|
 |-
-| 20
+| ESC
-| 20Hz
+|
+  Control (White Wire)
+|
+  P2.0 PWM
+|
+  PWM motor(PWM::''pwm1'', 101);
+  motor.set(14.5);
+|
+  Sets PWM signal of 101 Hz
+  Sets duty cycle of 14.5% for forward movement
 |-
-| 50
+| Servo
-| 50Hz
+|
+  Control (White Wire)
+|
+  P2.1 PWM
+|
+  PWM servo(PWM::''pwm2'', 101);
+  servo.set(15);
+|
+  Sets PWM signal of 101 Hz
+  Sets duty cycle of 15% for no turn
 |-
-| Any other value
+| Speed Sensor
-| Invalid date rate
+|
-|}
+  Signal (White Wire)
+|
+  P2.2 PWM
+|
+|
-{| class="wikitable"
+  It contains a trigger magnet and an rpm sensor
-|+ Master Controller Communication Table
+  It works on Hall effect.
 |-
-| Message Number
+| CAN Transceiver
-| Purpose
-| Data Byte Pattern
-|-
-| 0x101
-| Ask for Boot and Version Info. of all Controllers
-|
- Byte[0]: Send a '1'
 |
-|-
+  Pin no. 1 Driver Input
-| 0x103
+  Pin no. 4 Receiver Output
-| Sync. Master System Time on all Controllers
 |
- Byte[0-3]: System Time [HH:MM:SS]
+  P0.1 CAN TD1
-|
+  P0.0 CAN RD1
-|-
-| 0x201
-| Master Gets Status Update from all controllers
 |
- Byte[0]: Boot Status
- Byte[1]: Version Info.
 |
+  TI CAN Transceiver SN65HVD232D
+  Pin 7 - CAN H & Pin 6 - CAN L
 |-
-| 0x203
+|}
-| Master Gets current Time from all Controllers
-|
+==== Software Flow ====
- Byte[0-3]: Time in [HH:MM:SS]
+[[File: CmpE243_F14_T3_MotorFC.jpg]]
-|
+==== Implementation ====
+{| class="wikitable"
+|+ Motor Controller Communication Table
 |-
-| 0x301
+| Message Number
-| Master Enable Main UI in Android
+| Purpose
-|
+| Data layout
- Byte[0]: Send a '1'
-|
 |-
-| 0x302
+| 0x508
-| Master set GPS Destination on Geo Controller
+| Speed Sensor Data
 |
-  Byte[0-3]: Latitude Value
+  byte [0] : Speed sensor value in rpm
- Byte[4-7]: Longitude Value
+|-
+| 0x503
+| Vehicle Direction/Movement Data
 |
+ byte [0] : Movement Control
+x1 : Forward Fast
+x2 : Forward Slow
+x3 : Right
+x4 : Left
+x5 : Stop
+x6 : Back Right
+x7 : Back Left
+x8 : Back
 |-
-| 0x303
+|}
-| Master set Longitude Way-Points on Geo
-|
+==== Testing and Technical Challenge ====
-  bytes [0-1] : Total Way-Points count
+*Motor Controller
-  bytes [2-3] : Way-Point index
+**ESC
- bytes [4-7] : Longitude(float)
+***Electronic Speed Control is tricky to handle since it has its own pre-programmed micro-controller inside it which needs calibration according to the user manual.
-|
+***We started with calibrating the ESC using RC car's transmitter, but later we had to write our own calibration code.
+**Motor
+***We tested the motor speed by measuring the PWM signal on oscilloscope. We started by reading the PWM signal on oscilloscope while manipulating the speed of the RC car using its transmitter module.
+***Since the car was made for racing purpose, we had to keep the speed to its lowest value.
+***The transmitter and receiver of the RC car was detached from it. We gave PWM signal to the ESC and Servo through SJOne board.
+***It turned out that ESC was not accepting the PWM signal because it needed calibration each time its setting is changed.
+***We overcame this problem by including a calibration init code in our program.
+***We also noticed that as we added more hardware on top of the car, its speed was affected because of the load. We had to change the PWM value accordingly.
+**Servo
+***Since servo was not connected to the ESC it was pretty easy to handle. We could give PWM signal directly to servo and it moved accordingly.
+== '''Sensor Controller''' ==
+==== Group Members ====
+  '''''Deepak Yadav'''''
+  '''''Vinod Pangul'''''
+==== Sensor Team Schedule ====
+{| class="wikitable"
 |-
-| 0x304
+! scope="col"| Sl.No
-| Master set Latitude Way-Points on Geo
+! scope="col"| Start Date
-|
+! scope="col"| End Date
- bytes [0-1] : Total Way-Points count
+! scope="col"| Task
- bytes [2-3] : Way-Point index
+! scope="col"| Status
- bytes [4-7] : Latitude(float)
+! scope="col"| Actual Completion Date
-|
 |-
-| 0x305
+! scope="row"| 1
-| Master Send GPS FIX Ack to Bridge
+| 10/6/2014
-|
+| 10/18/2014
- Byte[0]: Send a value '1'
+| Order Ultra Sonic Sensors
-|
+| Completed [Got two sensors (front and back), 2 more (front right & left) to order ->Completed.]
+| 10/19/2014
 |-
-| 0x306
+! scope="row"| 2
-| Master Send Dest. Reached Ack to Bridge
+| 10/9/2014
-|
+| 10/9/2014
- Byte[0]: Send a Value '1'
+| Sensor Data Sheet review with the team
-|
+| Completed
+| 10/9/2014
 |-
-| 0x500
+! scope="row"| 3
-| Display Boot and Version Info. on LCD
+| 10/9/2014
-|
+| 10/16/2104
- Byte[0]: Boot Status Response
+| Sensor code development
- Byte[1]: Version Info.
+| Completed (Implementing filter (HW/SW) to get more accurate data ->(Done). Add logic to get the rest of the three sensor(front right/left and back data)->(Done) (Note: Delayed due to the implementation of CAN structure and calibration of IR sensor)
-|
+| 10/21/2014
 |-
-| 0x501
+! scope="row"| 4
-| Display Controllers Time on LCD
+| 10/22/2014
-|
+| 10/25/2014
- Byte[0-3]: Time in [HH:MM:SS]
+| Sensor software testing
-|
+| Completed
+| 10/25/2014
 |-
-| 0x502
+! scope="row"| 5
-| Display Destination Has Reached
+| 10/25/2014
-|
+| 10/28/2014
- Byte[0]: Send a '1'
+| Sensor real time testing
-|
+| Completed
+| 10/28/2014
 |-
-| 0x503
+! scope="row"| 6
-| Master Set Speed and Direction of Motor
+| 10/13/2014
-|
+| 10/15/2014
- Byte[0]: LEFT/RIGHT (or) FRONT/BACK command
+| Light sensor code Development
-|
+| Completed
+| 10/14/2014
 |-
-| 0x504
+! scope="row"| 7
-| Display Speed of Motor on LCD
+| 10/13/2014
-|
+| 10/15/2014
- Byte[0]: Speed Value
+| Accelerometer sensor code Development to detect tilt
-|
+| Completed
+| 10/14/2014
 |-
-| 0x505
+! scope="row"| 8
-| Display GPS and Compass values on LCD
+| 10/15/2014
-|
+| 10/15/2014
- Byte[0-1]: New Degree to Head
+| Light Sensor and Accelerometer Testing
- Byte[2-3]: Dist to Destination
+| Completed
- Byte[4-5]: Current Degree value
+| 10/15/2014
-|
 |-
-|0x506
+! scope="row"| 11
-| Display Sensor Values on LCD
+| 11/03/2014
-|
+| 11/04/2014
- Byte [0]: Front sensor value in inches
+| Common Communication SW code implementation and testing
- Byte [1]: Front Left sensor value in inches
+| Completed
- Byte [2]: Front Right sensor value in inches
+| 11/04/2014
- Byte [3]: Back sensor value in inches
-|
 |-
-|0x507
+! scope="row"| 11
-| Display Battery Status on LCD
+| 11/04/2014
-|
+| 11/09/2014
- Byte[0]: Battery Status Value
+| Complete Hardware testing-1
-|
+| Completed
+| 11/09/2014
 |-
+! scope="row"| 12
+| 11/10/2014
+| 11/15/2014
+| Complete Hardware testing-2
+| Completed
+| 11/15/2014
 |}
+==== Sensors : Sonar Sensors + Light and Accelerometer sensor====
+==== Hardware Design ====
+[[File:CmpE243_F14_T3_HardwareInterface.png]]
-{| class="wikitable"
+====A) Sonar Sensor:====
-|+ Motor Controller Communication Table
-|-
+[[File:CmpE243_F14_T3_sonarSensor.jpg]]
-| Message Number
-| Purpose
+*The LVMax long distance sonar sensors are used to detect the objects. We used four such sensors, three in the front and one in the back to get wide angle vision for the car. The Sonar Sensors sends sound waves when triggered and then the sensor signal emits a PWM that needs to be timed to detect the distance. The PWM width depends on the time it takes for the sound waves to bounce back from an object. The following figure explains how the distance is calculated.
-| Data layout
+[[File:CmpE243_F14_T3_Sensor.jpg]]
-|-
-| 0x508
+====B) Light and Accelerometer Sensor:====
-| Speed Sensor Data
+*The inbuilt accelerometer and light sensor on SJoneBoard is used to read their values. The inbuilt driver libraries provide by Prof. Preet is used to read both the accelerometer and the light sensor value and broadcast it over CAN bus for the detection of Car's light and front light of the car.
-|
- byte [0] : Speed sensor value in rpm
+==== Software Design ====
-|-
+===== Sonar Sensor =====
-| 0x509
+*Configure PW as input
-| Vehicle Direction/Movement Data
+*Enable PW as Rising and falling edge interrupt
-|
+*Configure RX as output, and give a 20uS Pulse of HIGH then LOW
- byte [0] : Movement Control
+*Take a snapshot of a hardware timer (T1) or start a hardware timer When Rising edge interrupt occur on PW.
-x1 : Forward
+--> After few microsecond <--
-x2 : Reverse
+*PW will go HIGH,take a snapshot of a hardware timer or start a hardware timer When Rising edge interrupt occur
-x3 : Stop
+--> After some time <--
- byte [1] : Steering Control
+*PW will go LOW and the interrupt on falling edge will now trigger, Take a snapshot of a hardware timer (T2).
-x1 : Left
+*Calculate the time difference (T2-T1) and convert the time into inches/CM (Formula is provided by the datasheet).
-x2 : Right
-x3 : Straight
+[[File:CmpE243_F14_T3_SensorFlowChart.png]]
-|-
-|}
+===== Light and Accelerometer =====
+*The library provided with SJOne Board has drivers for light and Accelerometer sensors. The only thing is to be done is to read the light sensor and accelerometer sensor data and broadcast to Master controller over CAN bus at rate of 1Hz.
+[[File:CmpE243_F14_T3_LightAccl.png]]
+===== Sensor Controller Task =====
+*Below is the overall flowchart of the sensor controller task.
+[[File:CmpE243_F14_T3_SensorTask.png]]
+==== Implementation ====
 {| class="wikitable"
@@ Line 1,020: / Line 1,129: @@
 |-
 | 0x511
-| Accelerometer/Light/Battery Sensor Data
+| Accelerometer/Light Sensor
 |
   byte [0] : X axis Value
@@ Line 1,026: / Line 1,135: @@
   byte [2] : Z axis Value
   byte [3] : Light sensor value
- byte [4] : Battery status value
 |-
 |}
+==== Testing and Technical Challenge ====
+*Front and Back Sensors Controller
+**To test the Sonar sensors, We placed the object in front of the sonar sensor and checked the pulse generated by the sonar sensors on Oscilloscope. The sensors data is verified by printing it on the Output terminal. We also tested the working of sensor with the moving car. We logged the data on the SD card and also displayed it on the seven segment display when the car was moving.
+We used Maxbotix LV-MaxSonar sensors. It has Three mode for getting data-Pulse width (PW), Analog (AN) and RS232. We went for Pulse width mode, because RS232 found to be very inaccurate and needed more pin connections (RX,TX,GND and 4 UART), SJOne board has only three available analog pins for use and we needed 4 of them and also they were not fast enough and their minimum distance is only 6 inch. So, we decided to go for Pulse width mode. The PW mode are much accurate and they are fast. Their distance range is from 3 inch to 254 inch. Moreover, PW can be connected to GPIO pins with external interrupt functionality. Since SjOne Board has more available GPIO pins on Port2 with external Interrupt functionality, PW mode option was chosen.
+The sonar sensors needs some time of delay to complete the full distance reading if no object is detected within the max range.The delay is ~50ms for each sensor to complete the distance calculation. So, a min 50ms delay is needed between every next triggering of RX pin. The value provided by the sensors are accurate, but not very stable. We tried using mode filters to avoid unstable readings. The only drawback of using filters was that it slowed down the sensors reading. After few experiment we found out that sensors are much more stable and provide a very accurate reading when we put a large delay around 20 ms between toggling the trigger pin (RX) and polling on CPU and not using external interrupt for calculating the distance time. This method is a very bad design as it can consume unnecessary CPU time, and its max range is not accurate and fixed (due to timeout delay), and it may give inaccurate reading if any interrupt occur. Since sensor task had no other major task running and after few experiment we found out that without using external interrupt and just polling the sensor value (bad design approach) was more reliable and accurate!!. The future implementation would be to find the solution to get the more reliable and accurate data using external interrupt function.
+== '''Geographical Controller''' ==
+==== Group Members ====
+ '''''Bhushan Gopala Reddy'''''
+ '''''Ryan Marlin'''''
+ '''''Rishikesh Nagare'''''
+==== Geographical Team Schedule ====
 {| class="wikitable"
-|+ GPS Controller Communication Table
 |-
-| Message Number
+! scope="col"| Sl.No
-| Purpose
+! scope="col"| Start Date
-| Data layout
+! scope="col"| End Date
+! scope="col"| Task
+! scope="col"| Status
+! scope="col"| Actual Completion Date
 |-
-| 0x518
+! scope="row"| 1
-| Send GPS Data to Master
+|
-|
+/4/2014
-  byte [0] : New Degree
+|
-  byte [1] : Distance
+/13/2014
-  byte [2] : Current Degree
+|
+Research and Order GPS module
+|
+Received GPS module
+|
+/7/2014
 |-
-| 0x519
+! scope="row"| 2
-| Send GPS FIX ACK to Master
+|
-|
+/7/2014
-  byte[0]: Send a '1'
+|
+/18/2014
+|
+Interface GPS module with LPC1758
+|
+Finished
+|
+/17/14
 |-
-| 0x52A
+! scope="row"| 3
-| Send Destination Reached ACK to master
+|
-|
+/14/2014
-  byte[0]: Send a '1'
+|
+/18/2014
+|
+Receive Compass module from Preet
+|
+Received
+|
+/9/2014
 |-
-|}
+! scope="row"| 4
+|
+/18/2014
-{| class="wikitable"
+|
-|+ IO Communication Table
+/4/2014
+|
+Parse GPS data and setup constructs to send appropriate data
+|
+Finished
+|
+/1/2014
 |-
-| Message Number
+! scope="row"| 5
-| Purpose
+|
-| Data layout
+/14/2014
+|
+/18/2014
+|
+Interface the Compass Module
+|
+Finished
+|
+/16/2014
 |-
-| 0x520
+! scope="row"| 6
-| Subscribe to Sensor data
+|
-| bytes [0-5] : Sensor Value in Inches
+/25/2014
+|
+/4/2014
+|
+Calibration of Compass
+|
+Finished
+|
+/1/2014
 |-
-| 0x521
+! scope="row"| 7
-| Subscribe to Motor data
+|
-| bytes [0-2] : Vehicle Direction
+/4/2014
+|
+/11/2014
+|
+Integrate GPS and Compass data
+|
+Finished
+|
+/4/2014
 |-
-| 0x522
+! scope="row"| 8
-| Subscribe to Compass Data
+|
-| bytes [0] : Compass Data in degrees
+/25/2014
-|-
+|
-| 0x523
+/30/2014
-| Subscribe to Battery Status
+|
-| bytes [0] : Battery Status Value
+Testing and mapping of GPS co-ordinates
+|
+Finished
+|
+/20/2014
 |-
+! scope="row"| 9
+|
+/18/2014
+|
+/18/2014
+|
+Final integration and testing
+|
+Finished
+|
+/15/2014
 |}
+==== Hardware Design ====
+[[File:CmpE243_F14_T3_HWDesign.png]]
+==== Hardware Interface ====
 {| class="wikitable"
-|+ Communication Bridge Communication Table
+|+ Geographical Controller Pin Connectivity Table
 |-
-| Message Number
+! scope="col"| '''Description'''
-| Purpose
+! scope="col"| '''Your Device Port'''
-| Data layout
+! scope="col"| '''SJOne Development Board Port'''
 |-
-| 0x528
+| Supply Voltage
-| Set Car Speed (Kill Switch) - temporary allow for other non-zero value for demo
+| Vcc
-| byte[0] - speed value
+| 3v3
 |-
-| 0x529
+| Ground
-| Destination GPS location
+| GND
+| GND
+|-
+| GPS Module
 |
-bytes [0-3] : latitude (float)
+ Channel 1 -> Rx, Channel 2 -> Tx
-bytes [4-7] : longitude (float)
-|-
-| 0x52A
-| Turn to degree
 |
-bytes [0-3] : degree(float)
+ Channel 1-> Tx P2.8, Channel 2-> Rx P2.9
 |-
-| 0x52B
+| Compass
-| Way points longitude
+|
-|
+ SCL
-  bytes [0-1] :total waypoints count
+  SDA
-  bytes [2-3] :waypoint index
+|
-  bytes [4-7] : longitude(float)
+  SCL2 -> P0.11
+  SDA2 -> P0.10
 |-
-| 0x52C
+| CAN Transceiver
-| Way points latitude
 |
-  bytes [0-1] :total waypoints count
+  Pin no. 1 Driver Input
-  bytes [2-3] :waypoint index
+  Pin no. 4 Receiver Output
- bytes [4-7] : latitude(float)
-|-
-| 0x52D
-| remote status (ie. Android connection status)
 |
-  bytes [0]=>
+  P0.1 CAN TD1
-:disconnected(passive send)
+  P0.0 CAN RD1
-:on disconnect(active)
-:connected(passive)
-:on connect(active)
-xFF:error(active/passive)
 |-
 |}
-=== Pin Connectivity Table ===
+==== Software Design ====
+[[File:CmpE243 F14 Team3OP GPS Module Software Top.jpeg||800px||Top level view of GPS software flow]]
+<br>
-{| class="wikitable"
+The figure above shows a top level view of the geographical team's software flow. The main message task, shown in the middle, is responsible for handling and updating the CAN message pointer. The CAN message pointer is read and handled in a separate periodic task that runs and sends messages across the CAN bus at frequencies of 1, 5, 10 or 20 Hz.
-|+ Sensor Controller Pin Connectivity Table
-|-
+The GPS and compass tasks, shown on the left and right respectively, collect their respective data and send that data to the message task. The message task will grab this data and stuff the CAN message variable to be sent to the Master module.
-! scope="col"| '''Description'''
-! scope="col"| '''Your Device Port'''
+[[File:CmpE243 F14 TeamUndergrad GPS GPS.jpeg||600px]]
-! scope="col"| '''SJOne Development Board Port'''
+[[File:CmpE243 F14 TeamUndergrad GPS compass.jpeg||600px]]
-! scope="col"| '''Commands'''
+<br>
-! scope="col"| '''Note'''
+''GPS''<br>
+NMEA (National Marine Electronics Association)<br>
+*NMEA consists of sentences, the first word of which, called a data type, defines the interpretation of the rest of the sentence. <br>
+*Each Data type would have its own unique interpretation and is defined in the NMEA standard.<br>
+*In our project we are using RMC (Recommended Minimum GPS data).Below is an example of RMC data.<br>
+$GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4,230394,003.1,W*6A
+Where:
+     RMC          Recommended Minimum sentence C
+       Fix taken at 12:35:19 UTC
+     A            Status A=active or V=Void.
+.038,N   Latitude 48 deg 07.038' N
+.000,E  Longitude 11 deg 31.000' E
+.4        Speed over the ground in knots
+.4        Track angle in degrees True
+       Date - 23rd of March 1994
+.1,W      Magnetic Variation
+     *6A          The checksum data, always begins with *
+Connection and Software Flow GPS:
+SJone board and GPS module is connected using UART.
+At boot-up GPS tries to get fix for all possible satellites to get proper GPS values.
+''Compass''<br>
+The Compass works over the I2C bus interface. Based on the datasheet, the compass will send data when it receives a 'A' command.
+==== Implementation ====
+{| class="wikitable"
+|+ GPS Controller Communication Table
+|-
+| Message Number
+| Purpose
+| Data layout
 |-
-| Supply Voltage
+| 0x518
-|
+| Send GPS Data to Master
 |
-|
+  byte [0] : New Degree
-|
+  byte [1] : Distance
+  byte [2] : Current Degree
 |-
-| Ground
+| 0x519
-|
+| Send GPS FIX ACK to Master
-| GND
+|
-|
+  byte[0]: Send a '1'
-|
 |-
-| Sonar Sensor
+| 0x52A
-|
+| Send Destination Reached ACK to master
 |
-|
+  byte[0]: Send a '1'
-|
 |-
-| IR Sensor
+|}
-|
-|
+==== Testing and Technical Challenge ====
-|
+*Geographical Controller
-|
+**GPS
+***GPS data was relatively straightforward to receive, however we ran into quite a few issues trying to parse the data.
+***Often times we would read the UART data in the middle of the buffer being changes to the next data point, for example, the reading would look like this:
+****$GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4$GPRMC,123519,A,4807.038
+****Instead of the normal data point: $GPRMC,123519,A,4807.038,N,01131.000,E,022.4,084.4,230394,003.1,W*6A
+***By checking the Checksum at the end of the string, *6A, we were able to determine the number of characters that were supposed to be in the string and exclude any strings that did not have the correct number of characters.
+**Compass
+***The Compass data was also straight forward to get. The compass HMC6352 has many useful features as provided in the datasheet, We focused on using the basic output data mode with heading mode.
+***The Compass is very sensitive to any kind of magnetic interference. In our project it were the motors and we had to make sure we mount the compass as far as possible from the motors to avoid any interference even though we had the calibration mode set up.
+***Sometimes the SDA and SCL used to get short (not because of hardware problem) maybe due to line impedance or parasitic capacitance since the wires were close to each other. A software reset can solve the problem.
+== '''Android & Communication Bridge Controller''' ==
+==== Group Members ====
+ '''''Chia-Pin Tseng (Ben)'''''
+ '''''Johnny Yam'''''
+ '''''Kevin Beadle'''''
+==== Communication Bridge & Android Team Schedule ====
+{| class="wikitable"
 |-
-| CAN Transceiver
+! scope="col"| Sl.No
-| Pin no. 1 Driver Input
+! scope="col"| Start Date
-Pin no. 4 Receiver Output
+! scope="col"| Planned End Date
-| P0.1 CAN TD1
+! scope="col"| Task
-P0.0 CAN RD1
+! scope="col"| Status
-|
+! scope="col"| Actual End Date
-|
 |-
-|}
+! scope="row"| 1
+| 9/30/2014
+| 9/30/2014
-{| class="wikitable"
+| Obtain Bluetooth Module (already had one)
-|+ Motor Controller Pin Connectivity Table
+| Done
+| 9/30/2014
 |-
-! scope="col"| '''Description'''
+! scope="row"| 2
-! scope="col"| '''Your Device Port'''
+| 9/30/2014
-! scope="col"| '''SJOne Development Board Port'''
+| 10/14/2014
-! scope="col"| '''Commands'''
+| Develop Basic Android App with Bluetooth Sensor Communication
-! scope="col"| '''Note'''
+| Done
+| 10/7/2014
 |-
-| Supply Voltage
+! scope="row"| 3
-| 6V from NiMH battery
+| 10/11/2014
-| N/A
+| 10/14/2014
-|
+| Interface Bluetooth Module with SJSU Dev Board
-|
+| Done
+| 10/11/2014
 |-
-| Ground
+! scope="row"| 4
-| GND (Black Wire)
+| 10/12/2014
-| GND
+| 10/19/2014
-|
+| Be able to send bi-directional arbitrary messages between Android App and Dev Board via Bluetooth
-|
+| Done
+| 10/14/2014
 |-
-| ESC
+! scope="row"| 5
-|
+| 10/14/2014
-  Control (White Wire)
+| 11/21/2014
-|
+| Subscribe to all CAN messages and dump all of them via Bluetooth to Android App or web interface
-  P2.0 PWM
+| Done
-|
+| 11/24/2014
-  PWM motor(PWM::''pwm1'', 101);
-  motor.set(14.5);
-|
-  Sets PWM signal of 101 Hz
-  Sets duty cycle of 14.5% for forward movement
 |-
-| Servo
+! scope="row"| 6
-|
+| 10/14/2014
-  Control (White Wire)
+| 11/21/2014
-|
+| Ajax & Websocket server remote structure
-  P2.1 PWM
+| Done
-|
+| 11/01/2014
-  PWM servo(PWM::''pwm2'', 101);
+|-
-  servo.set(15);
+! scope="row"| 7
-|
+| 10/14/2014
-  Sets PWM signal of 101 Hz
+| 11/21/2014
-  Sets duty cycle of 15% for no turn
+| Be able to input GPS coordinates through either (or both) Android App and web interface and send through Bluetooth then CAN bus
+| Done
+| 11/24/2014
 |-
-| CAN Transceiver
+! scope="row"| 8
-|
+| 10/21/2014
-  Pin no. 1 Driver Input
+| 11/24/2014
-  Pin no. 4 Receiver Output
+| Android App and webpage GUI enhancements (Google Maps, Google Drive)
-|
+| Done
-  P0.1 CAN TD1
+| 11/24/2014
-  P0.0 CAN RD1
-|
-|
-  TI CAN Transceiver SN65HVD232D
-  Pin 7 - CAN H & Pin 6 - CAN L
 |-
+! scope="row"| 9
+| 10/21/2014
+| 11/30/2014
+| Data visualization (status, compass, speed, location,....)
+| Done
+| 11/30/2014
 |}
+==== Hardware Design ====
+[[File:bbee_LRG.jpg|300px|thumb|right|Bluetooth Bee Module]]
+*In order to facilitate wireless communication between the SJSU One Board and a Android device, a Bluetooth Bee module is used. This module was chosen because it can connect and mount directly onto the SJSU One Board's XBee breakout socket.
+*The Bluetooth Bee is a Serial Profile Port (SPP) Bluetooth interface that connects with the SJSU development board's UART3.
+==== Hardware Interface ====
+The relevant pin connectivity table between the Bluetooth Bee module and the SJSU One Development Board is shown below:
 {| class="wikitable"
-|+ I/O Controller Pin Connectivity Table
+|+ Communication Bridge Pin Connectivity Table
 |-
-! scope="col"| '''Description'''
+| Description
-! scope="col"| '''Your Device Port'''
+| Bluetooth Bee Port
-! scope="col"| '''SJOne Development Board Port'''
+| SJSU Development Board Port
-! scope="col"| '''Commands'''
+| CAN Transceiver
-! scope="col"| '''Note'''
 |-
-| Supply Voltage
+| 3.3V Supply Voltage
-| 5V supply
+| 3V3
-|
+| 3V3
-|
+| 3V3
-|
-  Receives 5V supply that is used to power up all the boards
 |-
 | Ground
-| GND
 | GND
+| GND
+| GND
+|-
+| UART Channel 1
+| TX
+| RX
 |
-|
 |-
-| LCD Display
+| UART Channel 2
+| RX
+| TX
 |
-  Rx pin
-  Tx pin
-|
-  Rx ---> TXD2 (Port 2.8)
-  Tx ---> RXD2 (Port 2.9)
-|
-  u2.putline("F0")
-  u2.putline("$CLR_SCR")
-  u2.putline("$GOTO:3:0")
-|
-  Initialization command for LCD
-  Clears the screen
-  Point the cursor to line number 0 and character number 3
 |-
-| CAN Transceiver
+| CAN TXD
-|
-  Pin no. 1 Driver Input
-  Pin no. 4 Receiver Output
-|
-  P0.1 CAN TD1
-  P0.0 CAN RD1
-|
 |
+| CAN TD1
+| TXD
+|-
+| CAN RXD
+|
+| CAN RD1
+| RXD
 |-
 |}
+The Bluetooth Bee Module interfaces with an Android device through Bluetooth. In addition, various commands and data are then sent and received to and from the CAN bus through the Bluetooth Module to the Android device.
-{| class="wikitable"
+==== Software Design ====
-|+ Geographical Controller Pin Connectivity Table
+*The bridge controller and Android APP work as routers
-|-
-! scope="col"| '''Description'''
+''Bridge Controller ''
-! scope="col"| '''Your Device Port'''
+*Bridge controller translates CAN bus data into plain text and send it to android platform
-! scope="col"| '''SJOne Development Board Port'''
+*The Bridge controller is comprised of the SJSU Development Board with the Bluetooth Bee Module.
-! scope="col"| '''Commands'''
+*The Bluetooth Bee Module can be configured by writing to UART3 specific commands as specified in the [http://www.seeedstudio.com/wiki/Bluetooth_Bee Bluetooth Bee Seeedstudio Wiki].
-! scope="col"| '''Note'''
+*The Bluetooth Bee Module was configured as SLAVE MODE via the command: ''\r\n+STWMOD=0\r\n'' (The Android device will act as the Bluetooth Master)
-|-
+*The Bluetooth device name was set to "Yam_BluetoothBee" using the command: ''\r\n+STNA=Yam_BluetoothBee\r\n''
-| Supply Voltage
+*Allowing other devices to connect to the Bluetooth Module was enabled using the command: ''\r\n+STOAUT=1\r\n''
-| Vcc
+*Finally the Bluetooth Bee Module started broadcasting/inquiring to connect to another device using the command: ''\r\n+INQ=1\r\n''
-| 3v3
+*There are many other commands, such as to change the default pincode value, but they were not used for this project.
-|
+{| style="width:800px;" |
+|[[File:CmpE243_F14_T3_Bridge_flow_Dia.png|700px|thumb|left|Bridge framework ]]
+|}
+The architecture for our bridge controller is to interconvert the data between Bluetooth message and CAN bus message.
+Bluetooth message uses simple plaintext to transfer data. However, before we can deal with the string data, to collect and assemble several bytes into a package is needed, because UART is byte based data transmission. I use a byte 0x13(which is ‘\r’ in C code) at the end byte.The bluetooth sender must send 0x13 in the end of every text message. This process is achieved by BluBeeTask_BT2CAN class.
+CAN bus message uses 29bits as message ID and 8bytes data length as a single package to communicate with the master controller.
+There are two main classes for the controller. BluBeeTask_BT2CAN and BluBeeTask_CAN2BT.
+*BluBeeTask_BT2CAN
+BluBeeTask_BT2CAN is responsible for receiving the data which comes from bluetooth(via UART).We can setup multiple message filters to receive and process certain message data.
+Filter setting format.
+     blutoothReceiverTask->addCMD(
+     BluBeeTask_BT2CAN::CMDProp::gen((char* cmd,
+                bool (*func)(BluBeeTask_BT2CAN *, char* CMDStr)));
+For example, there is a message format “Speed<data>” to control the speed of the automatic car. We can simply apply a filter as below
+     blutoothReceiverTask->addCMD(
+     BluBeeTask_BT2CAN::CMDProp::gen("Speed", SpeedCMD));
+then, we have a callback function “SpeedCMD” that can only receive speed setting messages.(For instance there is a message “Speed23” was sent by Android)
+     bool SpeedCMD(BluBeeTask_BT2CAN *sender, char* CMDStr)//CMDStr will be “23”
+     {
+         int speed = 0;
+         CMDStr=parseInt(CMDStr,&speed);//parse string “23” into integer 23
+         can_msg_t msg = { 0 };//CAN message
+         msg.msg_id = make_id(cid_master_controller, CAN_TX_CAR_SPEED_MSG_ID);
+         //Set the ID to send to master controller with speed message ID
+         *(int *) &(msg.data.bytes[0]) = speed;//First byte is the speed 23
+         return sender->Send2CAN(msg);//Send message via CAN bus
+     }
+You can see the call back function SpeedCMD is doing a very simple string processing, then, send it to the master controller via CAN bus.
+*BluBeeTask_CAN2BT
+What BluBeeTask_CAN2BT doing is actually very similar to BluBeeTask_BT2CAN. First, you need to apply CAN message filters and set the corresponding callback functions.
+Filter setting format.
+     CANReceiverTask->addMsgTamp(
+            BluBeeTask_CAN2BT::MsgProp::gen(
+                  (controller_id_t MsgIdTmp, controller_id_t Mask,
+            bool (*func)(BluBeeTask_CAN2BT *, can_msg_t Msg)));
+controller_id_t is the set of information of CAN message ID including source, destination, and message number. To setup a controller_id_t variable you can simply use a function make_id.
+     controller_id_t ID= make_id(destination,source,message Number);
+MsgIdTmp is the message ID that you wanna receive. Bit 1 in mask means that certain bit you need to compare between MsgIdTmp and received message ID.
+{| class="wikitable"
+|+ CAN message mask example
+|-
 |
-|-
+received message ID
-| Ground
-| GND
+[00,12,07]
-| GND
+MsgIdTmp
+[20,12,31]
+Mask
+[00,FF,00]
+Success
+First mask data 00 means ignore the first data difference between received message ID and MsgIdTmp(ignore 00!=20).
+Second mask data FF means you need to compare the second data. In this case both are 12, therefore, it passes the comparison
+Third mask data is 00 (ignore 07!=20).
 |
-|
+received message ID
-|-
-| GPS Module
+[00,12,07]
-|
- Channel 1 -> Rx, Channel 2 -> Tx
+MsgIdTmp
-|
- Channel 1-> Tx P2.8, Channel 2-> Rx P2.9
+[20,12,31]
-|
-|
+Mask
-|-
-| Compass
+[00,FF,FF]
-|
- SCL
+Failed
- SDA
-|
+Third mask data is FF, so we need to compare 07 and 31. Apparently, 07 is not equal to 31, so the comparison is failed.
- SCL2 -> P0.11
- SDA2 -> P0.10
-|
-|
-|-
-| CAN Transceiver
-|
- Pin no. 1 Driver Input
- Pin no. 4 Receiver Output
-|
- P0.1 CAN TD1
- P0.0 CAN RD1
-|
-|
-|-
 |}
-{| class="wikitable"
+For example, there is a compass message comes from master. We can simply apply a filter as below
-|+ Master Controller Pin Connectivity Table
+    can2btptr->addMsgTamp(
+            BluBeeTask_CAN2BT::MsgProp::gen(
+                    make_id(0, cid_master_controller,
+                            CAN_RX_DA_COMPASSSTATUS_MSG_ID), //Message ID templete
+                    make_id(0,0xFFF,0xFFF)//Mask means don’t compare source section
+                    , compassMSG));//Set Callback function compassMSG
+We have a callback function “compassMSG” that can only receive compass messages and whichmessage was come from master controller. Since bridge controller receive this information, so we don’t need to compare destination.
+  bool compassMSG(BluBeeTask_CAN2BT *canbt, can_msg_t Msg)
+  {
+      sprintf(STRBUFF, "geo::%d,%d,%d,%d\r", (int16_t) Msg.data.words[0],
+            (int16_t) Msg.data.words[1], (int16_t) Msg.data.words[2],
+            (int16_t) Msg.data.words[3]);
+      //convert those data into a string
+      //notice the end of the string is ‘\r’, which is needed
+      canbt->Send2BT(STRBUFF);// send to UART(Bluetooth)
+      return true;
+  }
+''Android Controller ''
+*Android platform receives the text data from bridge controller, then, transmit the data through ajax or websocket
+*External controller could be any TCP accessible device (simple pebble watch program (20 lines) are used to control start and stop)
+*One administrator(control and receive), multiple observers(only receive)
+*Number of way points and routing is dynamically determined and done using the Google Maps API
+{| style="width:800px;" |
+|[[File:CmpE243_F14_T3_bridge_framework.png|400px|thumb|left|Bridge framework ]]
+|[[File:CmpE243 F14 T3 bridge cross.png|800px|thumb|left|cross platform ]]
+|}
+{| style="width:800px;" |
+|[[File:CmpE243_F14_T3_Android_Intro.png|200px|thumb|left|Intro]]
+|[[File:CmpE243_F14_T3_Android_Menu.png|200px|thumb|left|Intro]]
+|[[File:CmpE243_F14_T3_Android_OverView.png|200px|thumb|left|Intro]]
+|[[File:CmpE243_F14_T3_Android_Map.png|200px|thumb|left|Intro]]
+|}
+<BR/>
+==== Implementation ====
+{| class="wikitable"
+|+ Communication Bridge Communication Table
 |-
-! scope="col"| '''Description'''
+| Message Number
-! scope="col"| '''Your Device Port'''
+| Purpose
-! scope="col"| '''SJOne Development Board Port'''
+| Data layout
-! scope="col"| '''Commands'''
+|-
-! scope="col"| '''Note'''
+| 0x528
+| Set Car Speed (Kill Switch) - temporary allow for other non-zero value for demo
+| byte[0] - speed value
 |-
-| Supply Voltage
+| 0x529
-|
+| Destination GPS location
-|
-|
 |
+bytes [0-3] : latitude (float)
+bytes [4-7] : longitude (float)
 |-
-| Ground
+| 0x52A
-|
+| Turn to degree
-| GND
-|
 |
+bytes [0-3] : degree(float)
 |-
-| CAN Transceiver
+| 0x52B
-| Pin no. 1 Driver Input
+| Way points longitude
-Pin no. 4 Receiver Output
+|
-| P0.1 CAN TD1
+ bytes [0-1] :total waypoints count
-P0.0 CAN RD1
+ bytes [2-3] :waypoint index
+ bytes [4-7] : longitude(float)
+|-
+| 0x52C
+| Way points latitude
+|
+ bytes [0-1] :total waypoints count
+ bytes [2-3] :waypoint index
+ bytes [4-7] : latitude(float)
+|-
+| 0x52D
+| remote status (ie. Android connection status)
 |
-|
+ bytes [0]=>
+:disconnected(passive send)
+:on disconnect(active)
+:connected(passive)
+:on connect(active)
+xFF:error(active/passive)
 |-
 |}
+==== Testing and Technical Challenge ====
+''TESTs''
+*100000 message(20bytes per message) Bluetooth transmission between board and android under 200fps with range <5m
+**100% success
+''ISSUE''
+*3G network server could not be access(3G network is used for long range communication)
+**might use google sheet or external server to communicate
+== '''I/O Unit Controller''' ==
+==== Group Members ====
+ '''''Shreeram Gopalakrishnan'''''
+ '''''Sreeharsha Paturu Gangadhara'''''
+==== IO Team Schedule ====
 {| class="wikitable"
-|+ Communication Bridge Pin Connectivity Table
 |-
-| Description
+! scope="col"| Sl.No
-| Bluetooth Bee Port
+! scope="col"| Start Date
-| SJSU Development Board Port
+! scope="col"| End Date
-| CAN Transceiver
+! scope="col"| Task
+! scope="col"| Status
+! scope="col"| Actual Completion Date
 |-
-| 3.3V Supply Voltage
+! scope="row"| 1
-| 3V3
+| 10/7/2014
-| 3V3
+| 10/13/2014
-| 3V2
+| Research and Order LCD Display
+| Ordered LCD Display
+| 10/13/2014
 |-
-| Ground
+! scope="row"| 2
-| GND
+| 10/14/2014
-| GND
+| 10/21/2014
-| GND
+| Interfacing LCD Display with LPC1758
+| Completed
+| 10/21/2014
 |-
-| UART Channel 1
+! scope="row"| 3
-| TX
+| 10/21/2014
-| RX
+| 10/28/2014
-|
+| Implementing CAN structure with LCD tasks.
+| Completed
+| 11/30/2014
 |-
-| UART Channel 2
+! scope="row"| 4
-| RX
+| 10/28/2014
-| TX
+| 11/04/2014
-|
+| Subscribe data from sensor and GPS controller,display it on LCD.
+| Completed
+| 11/08/2014
 |-
-| CAN TXD
+! scope="row"| 5
-|
+| 11/04/2014
-| CAN TD1
+| 11/11/2014
-| TXD
+| Setup hardware and write code for START, STOP and Headlight buttons.
+| Completed
+| 11/12/2014
 |-
-| CAN RXD
+! scope="row"| 6
-|
+| 11/11/2014
-| CAN RD1
+| 11/18/2014
-| RXD
+| Testing and mounting hardware on car.
+| Completed
+| 11/27/2014
 |-
+! scope="row"| 7
+| 11/18/2014
+| 11/25/2014
+| Final Testing
+| Completed
+| 12/15/2014
 |}
-=== Communication Bridge + Android ===
 ==== Hardware Design ====
-*In order to facilitate wireless communication between the SJSU One Board and a Android device, a Bluetooth Bee module is used. This module was chosen because it can connect and mount directly onto the SJSU One Board's XBee breakout socket.
+*The IO Control Unit manages the LCD Display, switch to start and stop the car
-*The Bluetooth Bee is a Serial Profile Port (SPP) Bluetooth interface that connects with the SJSU development board's UART3.
+*It receives CAN data from the Master controller and accordingly processes to display on the LCD through UART
-{| style="width:300px;" |
+* The 7 segment LED displays the CPU usage
-|[[File:bbee_LRG.jpg|300px|thumb|left|Bluetooth Bee Module]]
+''LCD Display ''
+*The LCD Display is placed on the rear side of our RC Car
+*It displays the sensor and GPS values in real time.
+[[File: CmpE243_F14_T3_LCD_values.JPG|500px]]
+==== Hardware Interface ====
+{| style="width:800px;" |
+|[[File:CmpE243_F14_T3_IO_Interface.JPG|700px|thumb|left|LCD hardware interface]]
 |}
-==== Hardware Interface ====
-The relevant pin connectivity table between the Bluetooth Bee module and the SJSU One Development Board is shown below:
 {| class="wikitable"
-|+ Communication Bridge Pin Connectivity Table
+|+ I/O Controller Pin Connectivity Table
 |-
-| Description
+! scope="col"| '''Description'''
-| Bluetooth Bee Port
+! scope="col"| '''Your Device Port'''
-| SJSU Development Board Port
+! scope="col"| '''SJOne Development Board Port'''
-| CAN Transceiver
+! scope="col"| '''Commands'''
+! scope="col"| '''Note'''
 |-
-| 3.3V Supply Voltage
+| Supply Voltage
-| 3V3
+| 5V supply
-| 3V3
+|
-| 3V2
+|
+|
+  Receives 5V supply that is used to power up all the boards
 |-
 | Ground
+| GND
 | GND
-| GND
-| GND
-|-
-| UART Channel 1
-| TX
-| RX
 |
+|
 |-
-| UART Channel 2
+| LCD Display
-| RX
-| TX
 |
-|-
+  Rx pin
-| CAN TXD
+  Tx pin
 |
-| CAN TD1
+  Rx ---> TXD2 (Port 2.8)
-| TXD
+  Tx ---> RXD2 (Port 2.9)
+|
+  u2.putline("F0")
+  u2.putline("$CLR_SCR")
+  u2.putline("$GOTO:3:0")
+|
+  Initialization command for LCD
+  Clears the screen
+  Point the cursor to line number 0 and character number 3
 |-
-| CAN RXD
+| CAN Transceiver
+|
+  Pin no. 1 Driver Input
+  Pin no. 4 Receiver Output
+|
+  P0.1 CAN TD1
+  P0.0 CAN RD1
+|
 |
-| CAN RD1
-| RXD
 |-
 |}
-The Bluetooth Bee Module interfaces with an Android device through Bluetooth. In addition, various commands and data are then sent and received to and from the CAN bus through the Bluetooth Module to the Android device.
 ==== Software Design ====
-*The bridge controller and Android APP work as routers
+{|
+[[File:LCD.jpg|400px|thumb|left|LCD Software Interface ]]
-''Bridge Controller ''
+|}
-*Bridge controller translates CAN bus data into plain text and send it to android platform
+<BR/>
-*The Bridge controller is comprised of the SJSU Development Board with the Bluetooth Bee Module.
+<BR/>
-*The Bluetooth Bee Module can be configured by writing to UART3 specific commands as specified in the [http://www.seeedstudio.com/wiki/Bluetooth_Bee Bluetooth Bee Seeedstudio Wiki].
+<BR/>
-*The Bluetooth Bee Module was configured as SLAVE MODE via the command: ''\r\n+STWMOD=0\r\n'' (The Android device will act as the Bluetooth Master)
+<BR/>
-*The Bluetooth device name was set to "Yam_BluetoothBee" using the command: ''\r\n+STNA=Yam_BluetoothBee\r\n''
+<BR/>
-*Allowing other devices to connect to the Bluetooth Module was enabled using the command: ''\r\n+STOAUT=1\r\n''
+<BR/>
-*Finally the Bluetooth Bee Module started broadcasting/inquiring to connect to another device using the command: ''\r\n+INQ=1\r\n''
+<BR/>
-*There are many other commands, such as to change the default pincode value, but they were not used for this project.
+<BR/>
+<BR/>
+<BR/>
+<BR/>
+<BR/>
+<BR/>
+<BR/>
+==== Implementation ====
+|[[File:cmpe243.team3.IO_FLOW.jpg‎|500px]]
+{| class="wikitable"
+|+ IO Communication Table
+|-
+| Message Number
+| Purpose
+| Data layout
+|-
+| 0x102
+| Send boot status and version info
+| bytes [0-2] : Status and version info
+|-
+| 0x505
+| Display GPS and compass values
+|
+ Byte[0-1]: New Degree to Head
+ Byte[2-3]: Dist to Destination
+ Byte[4-5]: Current Degree value
+|-
+| 0x506
+| Display Sensor Values
+|
+ Byte [0]: Front sensor value in inches
+ Byte [1]: Front Left sensor value in inches
+ Byte [2]: Front Right sensor value in inches
+ Byte [3]: Back sensor value in inches
+ Byte [4]: Speed value
+|-
+|}
+==== Testing and Technical Challenge ====
 {| style="width:800px;" |
-|[[File:Bridge main system flow Dia.png|700px|thumb|left|Bridge framework ]]
+|[[File:CmpE243_F14_T3_LCD_error.jpg|700px|thumb|left|LCD junk values]]
-|}
-''Android Controller ''
-*Android platform receives the text data from bridge controller, then, transmit the data through ajax or websocket
-*External controller could be any TCP accessible device (simple pebble watch program (20 lines) are used to control start and stop)
-*One administrator(control and receive), multiple observers(only receive)
-*Number of way points and routing is dynamically determined and done using the Google Maps API
-{| style="width:800px;" |
-|[[File:Bridge framework.png|400px|thumb|left|Bridge framework ]]
-|[[File:Bridge cross.png|800px|thumb|left|cross platform ]]
 |}
+->'''Junk values being printed:'''
+*Although this error was not a show stopper, LCD printed junk values whenever it was on and any of the boards were programmed.
+**So, the only solution was to never program the board (connect the board to laptop) when LCD is on.
+->'''Coding improvement'''
+*In the code, initially, the GPS, Sensor values were being printed in one line in the code. So, either the values were overwritten or there was shifting of those values. This was a synchronization issue.
+**Resolved it by, clearing each line in the LCD before printing it and used individual line in the code to print the values.
-{| style="width:800px;" |
+== Conclusion ==
-|[[File:T3OP Android Intro.png|200px|thumb|left|Intro]]
+The whole project experience was fun and very educational. We learned about how CAN bus, sonar sensor, accelerometer sensor, light sensor, gps and compass module and motor controllers works. We faced some technical challenges such as controlling the motor speed, getting the right distance value from the sonar sensor, getting accurate readings from gps and compass and some of the power issues such as the right amount of current to the DC motors.
-|[[File:T3OP_Android_Menu.png|200px|thumb|left|Intro]]
-|[[File:T3OP_Android_OverView.png|200px|thumb|left|Intro]]
-|[[File:T3OP_Android_Map.png|200px|thumb|left|Intro]]
-|}
-<BR/>
-=== Sensors : Sonar Sensors + IR Sensors ===
-====A) Sonar Sensor:====
-*The ultrasonic sensors are in air, non-contact object detection and ranging sensors that detect objects within an area.
-*We are using 3 such sensors in front to get wide angle vision for the car.
-*Ultrasonic sensors use high frequency sound to detect and localize objects in a variety of environments. Ultrasonic sensors measure the time of flight for sound
-that has been transmitted to and reflected back from nearby objects. Based upon the time of flight, the sensor then outputs a range reading.
-====B) Infrared Sensor (IR):====
-*The basic principle of operation of an infrared sensor is based on infrared light that is reflected when its hits an an obstacle. An IR receiver captures
-the reflected light and the voltage are measured based on the amount of light received.
-*IR Sensors have 3 pins to connect to SJOne Board:
-<br>1)	Ground (GND)
-<br>2)	+Vcc (5 V)
-<br>3)	Vo (ADC-4 is on P1.30, select this as ADC0.4)
-{| style="width:800px;" |
-|[[File:BlockDiag.JPG|700px|thumb|left|IR Sensor Block Diagram ]]
-|}
-{| style="width:800px;" |
-|[[File:IR Sensor Graph.JPG|700px|thumb|right|Calibrated voltage output with distance ]]
-|}
-===I/O Unit:===
-*The IO Control Unit manages the LCD Display, switch to start and stop the car
-*It receives CAN data from the Master controller and accordingly processes to display on the LCD through UART
-* The 7 segment LED displays the CPU usage
-''LCD Display ''
-*The LCD Display is placed on the rear side of our RC Car
-*It displays the sensor and GPS values in real time.
-{| style="width:800px;" |
-|[[File:LCD.jpg|400px|thumb|left|LCD Initialization ]]
-|}
-<BR/>
-=== Motor Controller ===
-==== Hardware Design ====
-[[File:Capture12.PNG|Anatomy of The Rustler]]
-===== Parts and their functions =====
-[[File:Capture7.PNG|thumb|right|Velineon 3500 Brushless Motor]]
-'''''Motor''''' : Our RC car came with Velineon 3500 Brushless Motor. One of the main drawbacks of brushless motor is that it requires a speed controller to change the field polarity. We can't just give power to the motor directly and expect it to go. We can almost consider the controller as an integral part of the motor itself.
-[[File:Capture5.PNG|thumb|left|Velineon VXL-3s ESC]]
-'''''ESC''''' : Electronic speed controller was the trickiest part to deal with, since it comes with a previously programmed microcontroller inside it. It needs callibration, for which you need to refer to the user manual. An electronic speed controller basically controls the power given to the motor. Our RC car came with VXL-3s ESC, which accepted 100 Hz PWM input signal whose duty cycle varied from 10% to 20%. When supplied with a 15% duty cycle at 100 Hz, the ESC responded by turning off the motor attached to its output.
-'''''Steering Servo''''' : Our RC car was equipped with a digital servo (Traxxas part #2075) for steering control. It does not require an ESC to operate. We can give PWM signal directly to the servo from the SJOne board. The servo accepted 100 Hz PWM input signal whose duty cycle varied from 10% to 20%, where 10% represents extreme right turn and 20% represents extreme left turn.[[File:Capture8.jpg|thumb|right|Steering Servo]]
-'''''Speed Sensor''''' : To measure the RPM and speed of our car, we used the speed sensor provided by Traxxas Telemetry. This magnetic speed sensor worked on Hall effect. To learn more about Hall effect sensors, you can click on this [http://en.wikipedia.org/wiki/Hall_effect_sensor wikipedia article]. Since the sensor was provided by the same brand of our car, the installation was quick and easy. Here's a reference [https://www.youtube.com/watch?v=xx-Ft_kzTzs video] on how to attach magnetic speed sensor to the RC car.
-[[File:Capture11.jpg|thumb|left|Traxxas 7-Cell 8.4V NiMH Battery Pack]]
-'''''Battery''''' : We used 7 Cell NiMH (Nickel-Metal Hydride) battery pack for our car but would recommend others to use Lipo (Lithium Polymer) batteries instead. NiMH batteries tend to discharge very quickly. Also we realized later that since this car was made for racing purpose, its speed was too fast for our project. We reduced the voltage by removing 2 cells from the 7 cell battery pack. So, go for the 5 cell battery pack instead. A Traxxas EZ-Peak Charger would help a lot while doing testing.
-==== Hardware Interface ====
-===== Motor and Servo Interface =====
-[[File:Capture13.PNG]]
-===== Speed Sensor Interface =====
-==== Software Design ====
-===== Master Controller =====
-The software implementation of the master controller is explained by the flowchart.
-[[file: CMPE243_Team3_MASTER.jpeg]]
-== Testing & Technical Challenges ==
-===Sensor Controller===
-*Front and Back Sensors Controller
-**Describe how you tested the Sensors and calibration of the sensors
-Mention the Issues you faced and also the solutions you'll used to overcome the problem.
-===Motor Controller===
-*Motor Controller
-**Describe how you tested the motors. Explain the speed control methods used and difficulties you faced during calibration.
-Mention the Issues you faced and also the solutions you'll used to overcome the problem.
-===I/O Controller===
-{| style="width:800px;" |
-|[[File:LCD error.jpg|700px|thumb|left|Bridge framework ]]
-|}
-->'''Junk values being printed:'''
-*Although this error was not a show stopper, LCD printed junk values whenever it was on and any of the boards were programmed.
-**So, the only solution was to never program the board (connect the board to laptop) when LCD is on.
-===Communication Bridge===
+This project can be expanded to include more features such as an sonar sensor connected to the servo motor that rotates 360 degree to get distance from all the sides. This can reduce the number of sonar sensors. Furthermore, a improvement can be done in master and motor controller to control the car more precisely by controlling the car movement more accurately. A future suggestion would be to avoid non avoidable obstacles such as grass or follow only the planned route (may be be using some sensors or image detection).
-''TESTs''
-*100000 message(20bytes per message) Bluetooth transmission between board and android under 200fps with range <5m
-**100% success
-''ISSUE''
+=== Project Demonstration Video ===
-*3G network server could not be access(3G network is used for long range communication)
-**might use google sheet or external server to communicate
-===Geographical Controller===
-*Geographical Controller
-**Describe how you tested the Compass and explain how did you manage to achieve the maximum accuracy.
-Mention the Issues you faced and also the solutions you'll used to overcome the problem.
-===Master Controller===
-*Master Controller functions as the brain of car. The only challenge was integrating the master controller with the remaining five controllers.
-**Describe how you tested the Master Controller and problems faced while integrating it with all the other controllers.
-Mention the Issues you faced and also the solutions you'll used to overcome the problem.
-== Conclusion ==
-=== Project Video ===
+*  [https://www.youtube.com/watch?v=GBdmSaDHRtw CmpE243_F14_T3_ProjDemo]
 === Project Source Code ===
@@ Line 1,627: / Line 1,942: @@
 == References ==
 === Acknowledgement ===
+We would like to thank our instructor Preet for always inspiring and encouraging us to learn and build cool projects related to embedded systems. We really appreciate his patience and his guidance. This was our first exposure to CAN bus communication and we learned a lot about it. Last but not the least we would like to thank our awesome team members for supporting each other and helping each other out while working on this project.
 === References Used ===
@@ Line 1,646: / Line 1,962: @@
 http://www.seeedstudio.com/wiki/Bluetooth_Bee
-=== Appendix ===
+http://www.adafruit.com/product/746

Difference between revisions of "F14: Team3-Self Driving Car - Optimus Prime"

Latest revision as of 08:55, 14 April 2015

Contents

Optimus Prime: The Self-driving Car

Abstract

Parts List & Cost

Team Schedule

Introduction

CAN Bus: A brief introduction

The Six Controllers

Design & Implementation

Controller Communication Table

Master Controller

Group Members

Description

Master Controller Team Schedule

Hardware Design

Hardware Implementation

Hardware Challenges and Difficulties

Hardware Interface

Software Design

Software Implementation

Implementation

Testing and Technical Challenge

Motor Controller

Group Members

Motor Controller Team Schedule

Hardware Design

Parts and their functions

Hardware Interface

Motor, Servo and Speed Sensor Interface

Software Flow

Implementation

Testing and Technical Challenge

Sensor Controller

Group Members

Sensor Team Schedule

Sensors : Sonar Sensors + Light and Accelerometer sensor

Hardware Design

A) Sonar Sensor:

B) Light and Accelerometer Sensor:

Software Design

Sonar Sensor

Light and Accelerometer

Sensor Controller Task

Implementation

Testing and Technical Challenge

Geographical Controller

Group Members

Geographical Team Schedule

Hardware Design

Hardware Interface

Software Design

Implementation

Testing and Technical Challenge

Android & Communication Bridge Controller

Group Members

Communication Bridge & Android Team Schedule

Hardware Design

Hardware Interface

Software Design

Implementation

Testing and Technical Challenge

I/O Unit Controller

Group Members

IO Team Schedule

Hardware Design

Hardware Interface

Software Design

Implementation

Testing and Technical Challenge

Conclusion

Project Demonstration Video

Project Source Code

References

Acknowledgement

References Used

Navigation menu

Search