Difference between revisions of "Embedded System Tutorial GPIO"

From Embedded Systems Learning Academy
Jump to: navigation, search
Line 102: Line 102:
<b>Extra Credit:</b> Do something creative, such as lighting up an LED based on a terminal command.
<b>Extra Credit:</b> Do something creative, such as lighting up an LED based on a terminal command.
[[My HTML Wiki]]

Revision as of 07:44, 7 February 2018


Interface your LPC17xx to a switch and an LED.

Although the interface may seem simple, you do need to consider hardware design and know some of the fundamental of electricity. There are a couple of goals for us :

  • No hardware damage if faulty software is written.
  • Circuit should prevent excess amount of current to avoid processor damage.

Required Background

  • You should know how to bit-mask variables
  • You should know how to wire-wrap
  • You should know fundamentals of electricity and the famous V = IR equation.


GPIO stands for "General Purpose Input Output". Each pin can at least be used as an output or input. In an output configuration, the pin voltage is either 0v or 3.3v. In input mode, we can read whether the voltage is 0v or 3.3v.

You can locate a GPIO that you wish to use for a switch or an LED by first starting with the schematic of the board. The schematic will show which pins are "available" because some of the microcontroller pins may be used internally by your development board. After you locate a free pin, such as P2.0, then you can look-up the microcontroller user manual to locate the memory that you can manipulate.

GPIO Design


Hardware Registers

The hardware registers map to physical pins. If we want to attach our switch and the LED to our microcontroller's PORT0, then here are the relevant registers and their functionality :

LPC17xx Port0 Registers
LPC_GPIO0->FIODIR Direction of the port pins, 1 = output
Read : Sensed inputs of the port pins, 1 = HIGH
Write : Control voltage level of the pin, 1 = 3.3v
LPC_GPIO0->FIOSET Write only : Any bits written 1 are OR'd with FIOPIN
LPC_GPIO0->FIOCLR Write only : Any bits written 1 are AND'd with FIOPIN


We will interface our switch to PORT0.2, or port zero's 3rd pin (counting from 0).
/* Make direction of PORT0.2 as input */
LPC_GPIO0->FIODIR &= ~(1 << 2);

/* Now, simply read the 32-bit FIOPIN registers, which corresponds to
 * 32 physical pins of PORT0.  We use AND logic to test if JUST the
 * pin number 2 is set
if (LPC_GPIO0->FIOPIN & (1 << 2)) {
    // Switch is logical HIGH
else {
    // Switch is logical LOW
Note that the "inline" resistor is used such that if your GPIO is mis-configured as an OUTPUT pin, hardware damage will not occur from badly written software.
Switch Circuit


We will interface our LED to PORT0.3, or port zero's 4th pin (counting from 0).
/* Make direction of PORT0.3 as OUTPUT */
LPC_GPIO0->FIODIR |= (1 << 3);

/* Setting bit 3 to 1 of IOPIN will turn ON LED
 * and resetting to 0 will turn OFF LED.
LPC_GPIO0->FIOPIN |= (1 << 3);

/* Faster, better way to set bit 3 (no OR logic needed) */
LPC_GPIO0->FIOSET = (1 << 3);

/* Likewise, reset to 0 */
LPC_GPIO0->FIOCLR = (1 << 3);
Given below are two configurations of an LED. Usually, the "sink" current is higher than "source", hence the active-low configuration is used more often.
Active-low LED circuit
Active-high LED circuit


At the end of this lab, you should be familiar with how a microcontroller's memory can access physical pins. Test your knowledge by doing the following:

  • Interface your board's GPIO pin to an external switch
  • Interface your board's GPIO pin to an LED
  • If the switch is pressed, light up an LED
  • Do not use any pre-existing library such as a GPIO class

Upload into the textbox just the relevant code, probably just main.cpp

Extra Credit: Do something creative, such as lighting up an LED based on a terminal command.

My HTML Wiki