S23: CAN CLAN
Contents
CAN CLAN
Picture of the RC Car
Abstract
Our goal for this project is to use knowledge we gathered from lectures to design, implement, and test a self-driving RC car using a Controller Area Network (CAN) bus for controller communication. The project involves FreeRTOS and utilizes periodic tasks (running at 1Hz, 10Hz, and 100Hz) to gather, process, and display data from various embedded modules.
Introduction
The project was divided into 5 modules:
- Sensor Information
- Motor Operation
- Geological Information
- Driver & LCD Manager
- Bridge & Android Application
Team Members & Responsibilities
Gitlab Project Link - https://gitlab.com/rashmi_sv/the_CAN_clan.git
- Driver Controller
- Motor Controller
- Geo Controller
- GPS Interfacing
- Mobile App
- Integration Testing
Zeel Jatinkumar Lia
- Sensor and Bridge Controller
- Ultrasonic sensors
- LCD interfacing
- Integration Testing
Priyam Hajisheth
- Hardware mounting
- Mobile App
- Integration Testing
Xinyu He
- Hardware solution
- Wiki Page Update
- Integration Testing
Hongjin Cheng
- Protoboard soldering and Hardware assembling
- Compass, RPM Sensor, DC and servo motor interfacing
- Integration Testing
Schedule
| Week# | Start Date | End Date | Task | Status |
|---|---|---|---|---|
| 1 | 03/01/2023 | 03/07/2023 |
|
|
| 2 | 03/08/2023 | 03/14/2023 |
|
|
| 3 | 03/15/2023 | 03/21/2023 |
|
|
| 4 | 03/22/2023 | 03/28/2023 |
|
|
| 5 | 03/29/2023 | 04/04/2023 |
|
|
| 6 | 04/05/2023 | 04/11/2023 |
|
|
| 7 | 04/12/2022 | 04/18/2022 |
|
|
| 8 | 04/19/2023 | 04/25/2023 |
|
|
| 9 | 04/26/2023 | 05/02/2023 |
|
|
| 10 | 05/03/2023 | 05/09/2023 |
|
|
| 11 | 05/10/2023 | 05/16/2023 |
|
|
| 11 | 05/23/2023 | 05/23/2023 |
|
|
Parts List & Cost
| Item# | Part Desciption | Vendor | Qty | Cost |
|---|---|---|---|---|
| 1 | RC Car | Traxxas [1] | 1 | $251.51 |
| 2 | CAN Transceivers | Amazon [2] | 4 | $43.72 |
| 3 | SJ-2 Board | 4 | $200.00 | |
| 4 | LV-MaxSonar-EZ1 Ultrasonic Range Finder | Amazon [3] | 4 | $131.20 |
| 5 | GPS | Amazon [4] | 1 | $10.99 |
| 6 | RPM Sensor | Amazon [5] | 1 | $16.76 |
| 7 | Buletooth | Amazon[6] | 1 | $15.99 |
| 8 | LCD Display | Amazon [7] | 1 | $10.99 |
| 9 | Battery/Charger | 1 | $62.95 | |
| 10 | Cable | Amazon [8] | 1 | $7.99 |
| 11 | LSM303AGR Compass | Adafruit [9] | 1 | $19.57 |
| 12 | Magnet holder | 1 | $8.09 | |
| 13 | 2*20 header | 1 | $7.59 | |
| 14 | RPM holder | 1 | $7.73 | |
| 15 | long stand off | 1 | $2.21 | |
| 16 | Mount board | 1 | None | |
| 17 | Protoboard | 1 | None | |
| 18 | Small stand off | None | ||
| 19 | Pin header | None | ||
| 20 | Switch for DC motor | 1 | None | |
| 21 | wire connectors | 1 | None |
Printed Circuit Board
The Following table indicate the pin connection of all Hardware .
This is the pictures show protoboard and the mount board.
CAN Communication
<Talk about your message IDs or communication strategy, such as periodic transmission, MIA management etc.> We are using 100HZ for CAN bus communication, 50HZ for sensors, 10HZ for calculation, 1HZ for printing. The following table shows the Message ID.
| Node | Message ID | |
|---|---|---|
| 1 | ULTRASONIC_TO_DRIVER | 100 |
| 2 | GPS_DESTINATION | 300 |
| 3 | DRIVE_STATUS_CMD | 50 |
| 4 | SELF_TEST_CMD | 600 |
| 5 | DRIVER_TO_MOTOR | 200 |
| 6 | DRIVER_SELF_TEST_RESULT | 610 |
| 7 | GEO_STATUS | 400 |
| 8 | GEO_SELF_TEST_RESULT | 620 |
| 9 | GEO_CURRENT_COORDS | 650 |
| 10 | MOTOR_TO_APP_DBG | 500 |
Hardware Design
<Show your CAN bus hardware design>
- The following is the CAN Transceiver Design logicwork.
DBC File
Gitlab link to our DBC file : https://gitlab.com/rashmi_sv/the_CAN_clan/-/blob/dev/dbc_file/dbc/project.dbc
<You can optionally use an inline image>
VERSION ""
NS_ :
BA_
BA_DEF_
BA_DEF_DEF_
BA_DEF_DEF_REL_
BA_DEF_REL_
BA_DEF_SGTYPE_
BA_REL_
BA_SGTYPE_
BO_TX_BU_
BU_BO_REL_
BU_EV_REL_
BU_SG_REL_
CAT_
CAT_DEF_
CM_
ENVVAR_DATA_
EV_DATA_
FILTER
NS_DESC_
SGTYPE_
SGTYPE_VAL_
SG_MUL_VAL_
SIGTYPE_VALTYPE_
SIG_GROUP_
SIG_TYPE_REF_
SIG_VALTYPE_
VAL_
VAL_TABLE_
BS_:
BU_: DBG DRIVER GEO MOTOR SENSOR_BRIDGE
BO_ 100 ULTRASONIC_TO_DRIVER: 5 SENSOR_BRIDGE
SG_ ULTRASONIC_TO_DRIVER_left : 0|10@1+ (1,0) [0|511] "cm" DRIVER
SG_ ULTRASONIC_TO_DRIVER_right : 10|10@1+ (1,0) [0|511] "cm" DRIVER
SG_ ULTRASONIC_TO_DRIVER_front : 20|10@1+ (1,0) [0|511] "cm" DRIVER
SG_ ULTRASONIC_TO_DRIVER_back : 30|10@1+ (1,0) [0|511] "cm" DRIVER
BO_ 300 GPS_DESTINATION: 8 SENSOR_BRIDGE
SG_ GPS_DEST_LATITUDE_SCALED_100000 : 0|32@1- (1,0) [0|0] "Degrees" GEO
SG_ GPS_DEST_LONGITUDE_SCALED_100000 : 32|32@1- (1,0) [0|0] "Degrees" GEO
BO_ 50 DRIVE_STATUS_CMD: 1 SENSOR_BRIDGE
SG_ DRIVE_STATUS_CMD_start : 0|1@1+ (1,0) [0|0] "" MOTOR
BO_ 600 SELF_TEST_CMD: 1 SENSOR_BRIDGE
SG_ SELF_TEST_CMD_start : 0|1@1+ (1,0) [0|0] "" MOTOR, GEO, DRIVER
BO_ 200 DRIVER_TO_MOTOR: 2 DRIVER
SG_ DRIVER_TO_MOTOR_steer : 0|8@1- (1,0) [0|0] "degrees" MOTOR, SENSOR_BRIDGE
SG_ DRIVER_TO_MOTOR_speed : 8|8@1- (1,0) [0|50] "mph" MOTOR, SENSOR_BRIDGE
BO_ 610 DRIVER_SELF_TEST_RESULT: 1 DRIVER
SG_ DRIVER_SELF_TEST_RESULT_status : 0|8@1+ (1,0) [0|0] "" SENSOR_BRIDGE
BO_ 400 GEO_STATUS: 8 GEO
SG_ GEO_STATUS_COMPASS_HEADING : 0|12@1+ (1,0) [0|359] "Degrees" DRIVER, SENSOR_BRIDGE
SG_ GEO_STATUS_COMPASS_BEARING : 12|12@1+ (1,0) [0|359] "Degrees" DRIVER, SENSOR_BRIDGE
SG_ GEO_STATUS_DISTANCE_TO_DESTINATION : 24|16@1+ (0.1,0) [0|0] "Meters" DRIVER, SENSOR_BRIDGE
SG_ GEO_STATUS_SATELLITE_LOCKED : 40|1@1+ (1,0) [0|0] "" DRIVER, SENSOR_BRIDGE
BO_ 620 GEO_SELF_TEST_RESULT: 1 GEO
SG_ GEO_SELF_TEST_RESULT_status : 0|8@1+ (1,0) [0|0] "" SENSOR_BRIDGE
BO_ 650 GEO_CURRENT_COORDS: 8 SENSOR_BRIDGE
SG_ CURR_LATITUDE_SCALED_100000 : 0|32@1- (1,0) [0|0] "Degrees" SENSOR_BRIDGE
SG_ CURR_LONGITUDE_SCALED_100000 : 32|32@1- (1,0) [0|0] "Degrees" SENSOR_BRIDGE
BO_ 500 MOTOR_TO_APP_DBG: 2 MOTOR
SG_ MOTOR_TO_APP_DBG_current_steer : 0|8@1- (1,0) [0|0] "degrees" SENSOR_BRIDGE
SG_ MOTOR_TO_APP_DBG_current_speed : 8|8@1- (1,0) [0|50] "mph" SENSOR_BRIDGE
BO_ 620 MOTOR_SELF_TEST_RESULT: 1 MOTOR
SG_ MOTOR_SELF_TEST_RESULT_status : 0|8@1+ (1,0) [0|0] "" SENSOR_BRIDGE
CM_ BU_ DRIVER "The LED display and driver controller driving the car";
CM_ BU_ MOTOR "The RPM sensor, DC and servo motor controller of the car";
CM_ BU_ SENSOR_BRIDGE "The Bluetooth and the sonar sensor controller of the car";
CM_ BU_ GEO "The GPS and compass sensor controller of the car";
BA_DEF_ "BusType" STRING ;
BA_DEF_ BO_ "GenMsgCycleTime" INT 0 0;
BA_DEF_ SG_ "FieldType" STRING ;
BA_DEF_DEF_ "BusType" "CAN";
BA_DEF_DEF_ "FieldType" "";
BA_DEF_DEF_ "GenMsgCycleTime" 0;
BA_ "GenMsgCycleTime" BO_ 100 1000;
BA_ "GenMsgCycleTime" BO_ 200 50;
Sensor ECU
<Picture and link to Gitlab> Sensor Node GitLab
Hardware Design
LV-MaxSonar-EZ1 Ultrasonic Range Finder
- MaxSonar-EZ1 detects objects from 0" to 254".
- 2.5-5.5V operation range. Low 2mA supply current.
- 42kHz Ultrasonic sensor with 20Hz reading rate.
- Incredibly Small Package Sonar Range Finder.
- Serial Output, PWM output, Analog Output.
Sensor Design
- We used 4 sensors-LV-MaxSonar-EZ1 Ultrasonic Range Finder. These ultrasonic sensors are used by the RC car for the purpose of obstacle avoidance. Three sensors were placed on the front side of the RC car and one on the back. They use I2C communication to send distance data to the SJ2 microcontroller. On the SJ2 microcontroller, P0.10 was used for SDA, and P0.11 was used for SCL. It takes in +5V supply voltage. A LED is soldering on sensors to indicate if the sensor is working well.
Software Design
<List the code modules that are being called periodically.>
- Sensors are divided into two groups:
- 1. Front-rear group
- 2. Left-right group
Each group use 50HZ. The following code shows how it being called periodically.
void periodic_callbacks__100Hz(uint32_t callback_count) {
CAN_RX_MSGS_FOR_BRIDGE();
Sensor_Controller__100hz_handler(callback_count);
can_ultrasonic_sensor_transmit_messages();
}
The following is the code for sensor controller.
#include "LV_sensor_controller.h"
#include "LV_sensor_pin_init.h"
static dbc_ULTRASONIC_TO_DRIVER_s ultra_sonic_data;
static gpio_s FRONT_OBSTACLE_LED;
static gpio_s LEFT_OBSTACLE_LED;
static gpio_s RIGHT_OBSTACLE_LED;
static gpio_s BACK_OBSTACLE_LED;
void Sensor_Controller_init(void) {
FRONT_OBSTACLE_LED = gpio__construct_as_output(GPIO__PORT_2, 2);
LEFT_OBSTACLE_LED = gpio__construct_as_output(GPIO__PORT_2, 0);
RIGHT_OBSTACLE_LED = gpio__construct_as_output(GPIO__PORT_2, 1);
BACK_OBSTACLE_LED = gpio__construct_as_output(GPIO__PORT_2, 4);
adc_init_for_LV_sensors();
trigger_pins_for_LV_sensors();
}
void Sensor_Controller__print_sensor_values() {
printf("L:%d F:%d R:%d B:%d\n", ultra_sonic_data.ULTRASONIC_TO_DRIVER_left,
ultra_sonic_data.ULTRASONIC_TO_DRIVER_front, ultra_sonic_data.ULTRASONIC_TO_DRIVER_right,
ultra_sonic_data.ULTRASONIC_TO_DRIVER_back);
}
static void update_obstacle_LED(int sensor_value, gpio_s obstacle_led) {
if (sensor_value > 100) { // no obstacle detected. Turn OFF LED
gpio__reset(obstacle_led);
} else {
gpio__set(obstacle_led); // obstacle detected. Turn ON LED
}
}
void Sensor_Controller__100hz_handler(uint32_t callback_count) {
if (callback_count % 2 == 0) {
collect_left_LV_sensor_values_buffer();
ultra_sonic_data.ULTRASONIC_TO_DRIVER_left = sort_sensor_buffer_data_and_get_median(LEFT_ULTRA_SONIC);
update_obstacle_LED(ultra_sonic_data.ULTRASONIC_TO_DRIVER_left, LEFT_OBSTACLE_LED);
collect_right_LV_sensor_values_buffer();
ultra_sonic_data.ULTRASONIC_TO_DRIVER_right = sort_sensor_buffer_data_and_get_median(RIGHT_ULTRA_SONIC);
update_obstacle_LED(ultra_sonic_data.ULTRASONIC_TO_DRIVER_right, RIGHT_OBSTACLE_LED);
}
else {
collect_back_LV_sensor_values_buffer();
ultra_sonic_data.ULTRASONIC_TO_DRIVER_back = sort_sensor_buffer_data_and_get_median(BACK_ULTRA_SONIC);
update_obstacle_LED(ultra_sonic_data.ULTRASONIC_TO_DRIVER_back, BACK_OBSTACLE_LED);
collect_front_LV_sensor_values_buffer();
ultra_sonic_data.ULTRASONIC_TO_DRIVER_front = sort_sensor_buffer_data_and_get_median(FRONT_ULTRA_SONIC);
update_obstacle_LED(ultra_sonic_data.ULTRASONIC_TO_DRIVER_front, FRONT_OBSTACLE_LED);
}
}
dbc_ULTRASONIC_TO_DRIVER_s get_ultra_sonic_data(void) { return ultra_sonic_data; }
Technical Challenges
< List of problems and their detailed resolutions>
- Issue: Sensors test well independently, but not sensitive when mount on RC car .
- Reason: Sensor do not have enough power supply.
- Solution: 1.check connecting and solder in protoboard.
- 2.Re-design the power supply plan.
- Issue: While using two brand sensors, Front sensor works well, but left/right sensor working randomly. For sensors couldn’t work well at the same time.
- Reason: We config the sensor in two groups, and it causes the sensors to crosstalk.
- Solution: 1. Only use one brand.
- 2.Turning on only two sensors at a time.(left + right then front +rear).
- Issue: Rear Sensor doesn't work well with bad mounting.
- Reason: the sensors are mounted heading to LCD.
- Solution: we use higher stand off of read sensor.
Motor ECU
Hardware Design
On protoboard, a single SJ2-C board labeled motor was designed to control Traxxas car, in witch included DC motor for back-forward control, a servo motor for steering control, and a RPM sensor for speed control.
Following are the key hardware component from the car.
Servo Motor
We are using Traxxas 2075 for this project which came with the car and it is responsible for steering the car. It takes the 6V power directly from ESC. The servo motor is controlled directly from the SJ2 micro-controller board. The PWM signal is supplied at a frequency of 100 Hz. Based on the duty cycle of the signal sent to the servo, the direction of servo motor can be changed.
RPM Sensor
The RPM sensor is used as an input to maintain a constant speed of the vehicle. The sensor we are using is Traxxas RPM sensor which using hall effect to detect the movement of the DC motor.
Mounting
Software Design
<List the code modules that are being called periodically.>
motor.h
#pragma once
#include <stdint.h>
void motor__init(void);
// Apply brake by setting the ESC throttle to neutral
void brake();
// Set the throttle to go forward
void go_forward(float dc_speed);
// Set the throttle to go in reverse
void go_reveser();
// Set the servo motor to go straight
void go_straight();
// Set the servo motor to turn left
void go_left(float servo_speed);
// Set the servo motor to turn right
void go_right(float servo_speed);
}
Technical Challenges
< List of problems and their detailed resolutions>
- Issue: RC-Car sometimes goes forward while the code commands it to backward, whereas sometimes goes backward when the code commands it to go forward.
- Reason: Do not initialize the RC car.
- Solution: Keep Neutral With remote more than 3 seconds. Otherwise, it may fail to receive the correct signals.
- Issue: Giving the command with sequence Forward-Neutral-backward. The car acts as Forward-stop-Forward.
- Reason: ignored the RC-Car protection mechanism.
- Solution: The command should be Forward-Neutral-Backward-Backward
Geographical Controller
<Picture and link to Gitlab>
Hardware Design
- GPS
- An Adafruit Ultimate GPS breakout module using the MTK3339 chipset is interfaced over UART to the Geographical controller to provide latitude and longitude updates.
- Compass
- Triple-axis accelerometer/magnetometer compass module. Inside are two sensors, one is a classic 3-axis accelerometer, which can tell you which direction is down towards the Earth (by measuring gravity). The other is a magnetometer that can sense where the strongest magnetic force is coming from, generally used to detect magnetic north.
Software Design
<List the code modules that are being called periodically.> The GEO controller consisted of 4 main parts which are:
- 1. GPS
- 2. Compass
- 3. Waypoints
- 4. Geo Algorithm
- 1. GPS
gps.h
#pragma once
#include "stdbool.h"
// Note:
// South means negative latittude
// West means negative longitutde
typedef struct {
float latitude;
float longitude;
} gps_coordinates_t;
void gps__init(void);
void gps__get_gps_data_and_parse_coordinates(void);
gps_coordinates_t gps__get_coordinates(void);
bool gps__get_satellite_lock_status(void);
}
- 2. Compass
compass.h
#pragma once
#include "compass.h"
void compass__init();
float compass__get_current_bearing();
}
- 3. Waypoints
waypoint.h
#pragma once
#include "gps.h"
#include <stdint.h>
uint16_t waypoints__calculate_heading_to_next_point(gps_coordinates_t current_coords, gps_coordinates_t dest_coords);
int waypoints__calculate_distance_to_dest(gps_coordinates_t current_coords, gps_coordinates_t dest_coords);
}
- 4. Geo Algorithm
haversine.h
#pragma once
double calculate_heading(double lat1, double lon1, double lat2, double lon2);
double calculate_distance_in_meters(double lat1, double lon1, double lat2, double lon2);
}
line-buffer.h
#pragma once
#include "app_queue.h"
#include <stdbool.h>
#include <stddef.h>
#include <stdint.h>
typedef queue_s line_buffer_s;
bool line_buffer__init(line_buffer_s *buffer, void *memory, size_t size);
bool line_buffer__add_byte(line_buffer_s *buffer, char byte);
bool line_buffer__remove_line(line_buffer_s *buffer, char *line, size_t line_max_size);
}
Technical Challenges
< List of problems and their detailed resolutions>
- Issue: Unable to get accurate coordinate from gps sensor. we will getting coordinate 30 kilometers away from correct location.
- Reason: Do not correct conversion in calculation.
- Solution: do conversion before calculation.
- Issue: In compass, we will getting values in the oppsite direction.
- Reason: This is the compass mechanism.
- Solution: subtract the compass from 360 degree
Communication Bridge Controller & LCD
<Picture and link to Gitlab>
Hardware Design
- LCD
- An Adafruit Ultimate GPS breakout module using the MTK3339 chipset is interfaced over UART to the Geographical controller to provide latitude and longitude updates.
Software Design
<List the code modules that are being called periodically.>
LCD_int.h
#pragma once
#include <stdint.h>
void init__LCD(void);
void reset__LCD(void);
void send_LCD_char(uint8_t character);
void send_LCD_string(char *input_string);
void send_LCD_command(uint8_t command);
void set_LCD_to_4_bit_mode(void);
}
LCD_process.h
#pragma once
#include "project.h"
void update_sensor_for_LCD(dbc_ULTRASONIC_TO_DRIVER_s *sensor_data);
void update_compass_for_LCD(dbc_GEO_STATUS_s *compass_data);
void update_motor_for_LCD(dbc_DRIVER_TO_MOTOR_s *motor_data_s);
void LCD_display_1Hz(void);
// void LCD_status__display_handle_1hz(void);
}
Technical Challenges
< List of problems and their detailed resolutions>
- Issue: LCD sometime does work well.
- Reason: We do not provide good power supply plan.
- Solution: we bought another power bank and adjust the power supply plan.
Master Module
<Picture and link to Gitlab>
Hardware Design
LCD is the most important hardware using to testing different design cases.
Software Design
Streer_processor to control left, right turn function.
steer_processor.h
#pragma once
#include "project.h"
#include <stdint.h>
typedef enum speed_throttle_level {
THROTTLE_LEVEL_0 = 0,
THROTTLE_LEVEL_1 = 4,
THROTTLE_LEVEL_2 = 5,
THROTTLE_LEVEL_3 = 6,
THROTTLE_LEVEL_4 = 7,
} speed_throttle_level_t;
typedef enum steer_angle_level {
STEER_SHARP_RIGHT = -60,
STEER_MEDIUM_RIGHT = -50,
STEER_SOFT_RIGHT = -45,
STEER_STRAIGHT = 0,
STEER_SOFT_LEFT = 45,
STEER_MEDIUM_LEFT = 50,
STEER_SHARP_LEFT = 60,
} steer_angle_level_t;
typedef enum obstacle_threshold_level {
OBSTACLE_THRESHOLD_LEVEL_0 = 0,
OBSTACLE_THRESHOLD_LEVEL_1 = 50, // unit cm
OBSTACLE_THRESHOLD_LEVEL_2 = 75, // unit cm
OBSTACLE_THRESHOLD_LEVEL_3 = 100, // unit cm
NO_OBSTACLE = 150, // unit cm
} obstacle_threshold_level_t;
void steer_processor(dbc_DRIVER_TO_MOTOR_s *motor_val, dbc_ULTRASONIC_TO_DRIVER_s sensor_val,
dbc_GEO_STATUS_s geo_heading);
void steer_processor__obstacle_LEDs_init();
}
Controller received message then navigate to destination. driver_controller.h
#pragma once
#include "stdbool.h"
void driver_controller__init();
void driver_controller__read_all_can_messages();
bool driver_controller__send_cmd_to_motor_over_can();
void print_heading_and_motor_cmds();
}
Technical Challenges
< List of problems and their detailed resolutions>
- Issue: difficulties with obstracl avoidance logic.
- Reason: complex logic to design.
- Solution: implementation different test cases and adjust the algorithm according to the results from actually test.
Mobile Application
<Picture and link to Gitlab>
APP Interface
Software Design
The map block is used to create and display a 2D map of the world for location, navigation and other map functions. It uses an open-source map library which is very similar to Google Maps. The Map bloc has several functions including display, zoom, direction, distance, coordinate calculation. Fireblot uses this block to locate a destination location for the car and send the corresponding latitude and longitude values. This is made possible by the marker block. Markers can be placed on any location on the map and the pinpointed location coordinates can be received as floating point integers. These values are displayed on the app and also used to send as a bluetooth message to the HC-05 module when required.
Technical Challenges
< List of problems and their detailed resolutions>
- Issue: Don't know how to start.
- Reason: not familiar with mobile app
- Solution: learn from some video .
Conclusion
Generally speaking ,this is a successful project for team CAN CLAN. We achieved all required functions, and bonus reverse function for the RC car. However, the process is not that easy. We were even still testing and debugging at the night before demo day.
<What did you learn?>
There are many problems we faced and learn to solve through the project:
- Hardware solution
We need to find a clear and easy solution to mount all components on the car. We were considered to order PCB board online. However, none of us used the PCB designers' software before. Since time limited, we switch to plan b, to mount on protoboard. To avoid connection fault, we need to draw the connection mechanism and soldering carefully. We also meet the wight balance issue, which makes RC car always go right. In order to solve that, we changed to use long stand off and put power bank in the mid.
- Test and debugging
we spend the most time on debugging. Tested each component again and again when is not working coordinately. To troubleshoot driving logic issue, we set many cases, test one by one, read the date from LCD, and adjust our code accordingly.
Project Video
https://www.youtube.com/watch?v=kvuTwDW_AXE
https://youtube.com/shorts/Oli5RZc1EBU?feature=share
Project Source Code
https://https://gitlab.com/rashmi_sv/the_CAN_clan
Advise for Future Students
- Teamwork is the most important key skills in this project.
- Plan your teamwork well. Meet to discuss tasks for the week, working individually, meet own weekend and debugging together.
- Assign task to suitable person.
- Read the wiki pages from previous groups as early as possible
- It will give you the key idea of the what the project about
- You are actually study how to code during the lab HW
- You may meet the same challenge they are facing
Acknowledgement
Don't hesitate to communication, talk to Preet, talk to TA, talk to other team. It will help you more clear about your own ideas, and may open a new direction solving problems.
References
- LV-MaxSonar-EZ1 Ultrasonic Range Finder
- Bearing and Distance computation formulas
- Bluetooth Tutorial
- Compass datasheet
- GPS tutorial
- Compass calibration tutorial
- Compass calibration tool
