S22: Silver Arrow

From Embedded Systems Learning Academy
Revision as of 06:40, 22 May 2022 by 243 user3 (talk | contribs) (Wheel Encoder)

Jump to: navigation, search

Project Title

<Team Name>



Abstract

<2-3 sentence abstract>

Introduction

The project was divided into N modules:

  • Sensor ...
  • Motor..
  • ...
  • Android

Team Members & Responsibilities

Pushkar Deodhar LinkedIn

  • App development
  • Mechanical/Hardware/circuit/PCB designing

Vilas Dhuri LinkedIn\

  • Driver Logic
  • Hardware and PCB designing

Rishabh Gupta LinkedIn

  • Driver Logic
  • Wiki page manage

Vivek Tapkir LinkedIn

  • Sensor controller
  • Communication Bridge Controller
  • Hardware Integration

Saharash Shivahre LinkedIn

  • Geo controller
  • Wiki page manage

Naveena Sura LinkedIn

  • Geo controller
  • Git repo managment

Daya Modekar LinkedIn

  • Motor controller
  • Hardware Integration and design





Schedule

Week# Start Date End Date Task Status
1 03/16/2022 03/22/2022
  • Read previous projects, gather information and discuss among the group members.
  • Distribute modules to each team member.
  • Completed
  • Completed
2
03/23/2022
03/29/2022
  • Purchased RC car and batteries.
  • Research and finalize which ultrasonic sensor the project will use
  • Purchased Bluetooth connector
  • Research math needed to determine the distance between navigation points. Decide on distance algorithm
  • Create a branch for motor controller driver. Create draft template API for motor controller
  • Using previous projects, determine what works needs to be completed for main board. Bring findings to weekly meeting
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
3
03/30/2022
03/04/2022
  • Ordered and received necessary parts for the car
  • Getting acquainted with the basics of the android studio application
  • Researched basic mobile application development
  • Completed basic driver logic code, Motor controller, and sensor node logic
  • Completed
  • Completed
  • Completed
4
04/05/2022
04/11/2022
  • Updated DBC file as per requirement
  • Completed ultrasonic sensor level testing
  • Completed Bluetooth configuration for mobile app connection, and established communication with SJ2 board
  • Developed a basic mobile application showing maps and current location
  • Began coding compass data
  • Ongoing testing of RPM sensors, motor logic, and sensors for different node
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • In Progress
5
04/12/2022
04/18/2022
  • Sensor data tuning and crosstalk avoidance by loading multiple samples into the buffer
  • Bridge controller data sending and receiving over Bluetooth has been established
  • Implement an application with a startup Bluetooth connection page and test bluetooth data transmission
  • Implement Maps page with OnClick marker with coordinates
  • Ensure CAN bus nodes are communicating correctly by verifying PCAN data.
  • Unit Test Direction Distance Calculation Module. Manual calculation of data should match module output
  • Tune driver and obstacle avoidance algorithm based on data from sensor nodes with unit-testing
  • Begin laying out hardware requirements for PCB and discuss hardware integration
  • Start researching on Wheel encoder according to the requirement
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • In Progress
  • In Progress
  • In Progress
6
04/19/2022
04/25/2022
  • Begin to analyze real-world tests from the previous week's implementation and perform fixes for issues faced
  • Final integration and of all modules (sent data from GPS&Compass to->Driver to->Motors & Wheels)
  • Start working on the PCB, order the PCB, and also purchase the required components
  • Integration testing with obstacle avoidance
  • Send Destination coordinates over BT to the Driver node
  • Complete Prototype 1
  • Incomplete
  • Incomplete
  • Incomplete
  • Incomplete
  • Incomplete
  • Incomplete


Parts List & Cost

Item# Part Desciption Vendor Qty Cost
1 RC Car Traxxas 1 $250.00
2 CAN Transceivers MCP2551-I/P Microchip [1] 8 Free Samples


Printed Circuit Board

<Picture and information, including links to your PCB>



CAN Communication

<Talk about your message IDs or communication strategy, such as periodic transmission, MIA management etc.>

Hardware Design

<Show your CAN bus hardware design>

DBC File

<Gitlab link to your DBC file> <You can optionally use an inline image>




Sensor ECU

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Motor ECU

Hardware Design

Motor Controller Node includes the operational control of the DC motor, Servo motor, Electronic speed control (ESC), and the wheel encoder(RPM Sensor). The job of the motor controller is to control the steering of front wheels at appropriate angles and to spin the rear wheels at speeds commanded by the driver node in order to traverse the RC car to the destination location.The DC motor, servo motor, and ESC(Traxxas ESC XL-05) were provided with the Traxxas RC car. The wheel encoder and the trigger magnet were purchased separately from Traxxas's website.

Motor Node Pinout
SJ2 Board Pin Description
5V Input power
3.3V CAN transceiver power
PWM2 P2.1 DC Motor Speed Control
PWM5 P2.4 Servo Motor Angle Control
CAP0 P2.6 RPM Sensor\Wheel Encoder
CAN1 TX CAN Transceiver Tx
CAN1 RX CAN Transceiver Rx
GND Grounding

DC Motor and ESC

The DC motor and ESC were provided with RC car. The DC motor is controlled by the ESC using PWM signals which were provided by the motor controller board for forward, neutral, and reverse movements. The ESC is powered ON using a 7.4 LiPo battery. The ESC converts this 7.4V to 6V and provides input to DC Motor.

DC Motor and ESC
ESC wires Description Wire Color
Vout Output Power (6V) RED
GND Ground BLACK
PWM PWM input from SJ2-Board (P2.1) WHITE

The car can be operated at 100Hz in the following 3 modes :
Sport Mode (100% Forward, 100% Brakes, 100% Reverse)
Racing Mode (100% Forward, 100% Brakes, No Reverse)
Training Mode (50% Forward, 100% Brakes, 50% Reverse)


Servo Motor

Servo Motor
Servo Wires Description Wire Color
Vin Input Voltage (6V) RED
GND Ground BLACK
PWM PWM input from SJ2-Board (P2.4) WHITE

The PWM frequency for our Traxxas Servo motor also needed to be 100Hz. An idle (wheel's pointing forward) duty cycle is 15%. The full duty cycle range is [10%, 20%], where [10%, 15%) is the steer left range, and (15%, 20%] is the steer right.

Wheel Encoder

For speed sensing we purchased a Traxxas RPM sensor as it mounted nicely in the gearbox. The RPM sensor works by mounting a magnet to the spur gear and a hall effect sensor fixed to the gearbox. To get the revolutions per second we used Timer2 as an input capture.

RPM Sensor
Trigger Magnet
RPM Sensor Wires Description Wire Color
Vin Input Voltage (6V) RED
GND Ground BLACK
Sensor Output Input Capture to SJ2-Board (P2.6) WHITE

Software Design

The motor controller code modules consisted of 3 main parts, which are: 1. PWM drivers and motor logic, 2. RPM/speed sensor, 3. PID controller.


Technical Challenges

  • First and foremost, the Traxxas motor ESC and other Traxxas components are Traxxas Hobby Parts, and they are not designed for development. As a result, no technical specification documentation or program/development guidelines are accessible. The motor ESC must be tested by supplying PWM duty cycles in different sequences at different duty cycle percentages. We utilized the remote control to recreate certain circumstances in which the ESC acted strangely.
  • If a Lipo battery is used, the ESC setup switches to the Lipo battery state. When the NiMH battery is replaced, the ESC begins flashing the led in a green-red pattern, and the ESC power button stops working. In this case, the handbook contains a calibration procedure that can rescue your boat and restore regular ESC operation.
  • Another challenge with the motor node program development is that you cannot rely on unit testing. Whoever works on the motor node, should make sure that the sequence of the duty cycles being fed to the ESC produces the expected results on the motor as well. The forward-reverse transitioning and the speed controlling both can be a bit tricky. Also, the hard brake logic can take a while to get working properly.
  • We somehow destroyed the ESC and wanted to replace it. We spent both time and money on this. Make sure you don't short the ESC by mistake!


Geographical Controller

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>





Communication Bridge Controller & LCD

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Master Module

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>



Mobile Application

<Picture and link to Gitlab>

Hardware Design

Software Design

<List the code modules that are being called periodically.>

Technical Challenges

< List of problems and their detailed resolutions>






Conclusion

<Organized summary of the project>

<What did you learn?>

Project Video

Project Source Code

Advise for Future Students

<Bullet points and discussion>

Acknowledgement

References