F17: Alpha

From Embedded Systems Learning Academy
Revision as of 17:08, 19 December 2017 by Proj user1 (talk | contribs) (Testing & Technical Challenges)

Jump to: navigation, search

Project Title

Alpha - Self-navigating RC car using CAN communication based on FreeRTOS.

Git Link - ALPHA
Git Users:

  • Anirudh1313
  • chhavi17
  • DoyalPatel
  • jigar29
  • kthnptl
  • rajvisharia
  • ShubhamKulkarni93
  • SnehaSharma
  • SushmaSJSU
  • SuchetaCiyer

Abstract

The aim of this project is the development of an autonomous RC car which navigates from a source location to destination location avoiding all obstracles on the way.This car is connected to GPS, Compass and Bluetooth and multiple sensors such as ultra sonic sensors and RPM sensors to fulfill the purpose of navigation, obstacle detection and avoidance.A Google map based android application is developed which finds the shortest path between current location and destination inside SJSU and connects to self-driving car using Bluetooth. The car can moves along the route provided by the application to reach the destination. Communication between all the modules on car is done through CAN. Cgreen Unit testing (For C++) and JUnit Test (For android) is used to improve performance. LCD, LEDs and headlights on the car are used for debugging issues and to get all relevant information of the status of the car, in real time.

Objectives & Introduction

Introduction

The project was divided into six modules:

1)Sensor Module : To detect the distance to an obstacle from the car using ultrasonic sensors.

2)Motor Module : To move the car forword and reverse with accurate speed and different steering angle.

3)Geographical Controller : To navigate the car in the direction of the destination using current location and heading angle of the car.

4)Master Module : To make all descision for the smooth navigation of the car.

5)Communication Bridge Controller & LCD : To establish communication between car and android application as well as displaying all the informaton of car on LCD.

Communication between above five modules is established using CAN Bus.

6)Android Application : To provide shortest path nevigation inside SJSU campus which communicates to car using bluetooth.

Objective

1) To be able to detect and avoid obstacle.

2) To be able to move in constant speed, able to increase and decrease speed as per requirement.

3) To be able to nevagate to current location to destination.

4) To be able to communicate with android application.

Team Members & Responsibilities

  • Master Controller
    • Jigar Agarwal
    • Sucheta Iyer
  • Geographical Controller
    • Chhavi Mehta
    • Krishna Sai Anirudh Katamreddy
  • Sensor Controller
    • Sneha Sharma
    • Sushma Macha
  • Communication Bridge Controller & LCD
    • Kathan Patel
    • Sushma Macha
  • Android Application
    • Doyal Patel
    • Sneha Sharma
  • Testing
    • Doyal Patel
    • Jigar Agarwal
    • Sucheta Iyer

Schedule

Week# Start Date End Date Task Status
1 09/15/2017 09/16/2017
  • Read previous projects, gather information and discuss among the group members.
  • Distribute modules to each team member.
Completed
2 09/17/2017 10/03/2017
  • Set up individual Git accounts and perform individual git commits on a GIT file.
  • Create a project report template on Wiki.
  • Finalize the scope of each individual modules.
  • Study the datasheet and prepare the high-level design.
  • Order an RC Car (appropriate height and suspension), rechargeable batteries, sensors, GPS and compass module.
Completed
3 10/04/2017 10/10/2017
  • Sensor: Interface individual sensor and observe the sensor readings under different conditions. Determine pins and architecture of board for all four sensors.
  • Motor: Test DC and servo motors using RC Transmitter and Receiver.
  • Master: CAN bus test interface with the sensor.
  • Communication Bridge Controller: Refer previous projects and get an overview of ‘Communication Bridge Controller’. Deciding the Bluetooth module and place orders based on the requirements.
  • Geo: Testing GPS and compass modules by checking connections from the datasheet.
  • Android: Android development environment setup and basic Android application development.
Completed
4 10/11/2017 10/17/2017
  • Sensor: Generate a DBC structure and acceptance filter for the sensor, and send the distance of an obstacle if any over the CAN bus. Interface multiple sensors and experiment with the angles of the sensors to have minimum interference.
  • Motor: Get the motors running using SJOne board based on the observation of the PWM waveforms for DC and servo motors on the Oscilloscope.
  • Master: Finalizing the PCB design and general hardware model layout. Brainstorming on CAN message details like ID, priority, etc.
  • Communication Bridge Controller: Understanding the RFCOMM Protocol for Bluetooth communication and Bluetooth hardware. Configure Bluetooth module using Bluetooth terminal.
  • Android: Work towards enabling Bluetooth in the Android environment and create a basic application for controlling a Bluetooth-enabled phone.
Completed
5 10/18/2017 10/24/2017
  • Complete all the Hardware setup for the project and prepare sensor stands of suitable height (positioned at suitable angle on the car).
  • Sensor: Develop an algorithm to trigger all the sensors sequentially i.e., MIDDLE, LEFT, RIGHT, and BACK. Interface sensors with LEDs to indicate the direction to be taken.
  • Motor: Get the motors to move Left, Right, Forward and Reverse through CAN communication from Master module (pressing the switches on Master module).
  • Master: Establish CAN communication between all the modules.
  • Communication Bridge Controller: Interfacing Bluetooth module with SJOne board and test the working of the module.
  • Geo: Interface GPS module to SJOne board using UART and collect the data from GPS and calcualte bearing angle.
  • Android: Establish basic communication between SJOne and mobile application.
Completed
6 10/25/2017 10/31/2017
  • Sensor: Calculate minimum and maximum range of obstacle detection and send the values to Master module. Interface the sensors to RC Car and take real-time readings on a moving car.
  • Motor: Design a robust algorithm to avoid obstacles based on the communication with Master and Sensor modules.
  • Master: Interfacing with the Motor Module and Sensor Module.
  • Communication Bridge Controller & Android: Bi-directional communication between SJOne board and Android application.
  • Geo: Take checkpoints at varios locations on the campus.
Completed
7 11/01/2017 11/07/2017
  • 3D print the sensor stands and place them on the board at proper angle and orientation.
  • Sensor: Test the obstacle detection algorithm with various obstacles like hard flat surfaces, curved surface etc. Stress test the sensors under different temperatures.
  • Motor: Get wheel feedback using RPM sensor values for vehicular movement on the slope.
  • Communication Bridge Controller: Interfacing Bluetooth module with the Master module over the CAN Bus.
  • Geo: Integrate GPS module with the compass and calibrating them with SJOne board as per the values obtained. Send Latitude and Longitude of the current position of the car on CAN Bus.
  • Android: Get important data required for the Android application over CAN Bus with the help of the Bluetooth module.
Completed
8 11/08/2017 11/14/2017
  • Motor: Modify the code to move slight left/right, half left/right, full left/right, straight or stop as per the GPS data sent by the Master module.
  • Master: Develop an algorithm to calculate the servo motor angle as er the data from Geo controller in order to move the car closer to the destination.
  • Geo: Send the heading and bearing angle difference based on the current position and next position to the Master module.
  • Communication Bridge Controller: Interfacing Bluetooth module with GPS module over the CAN bus.
  • Android: Add Google map to the application and get current location of the car. Implement an algorithm to find the shortest path by using different position marker on the Google map.
Completed
9 11/15/2017 11/21/2017
  • Car: Get Destination and Routing Path from the Android app. Develop an algorithm to move the car in the given routing path as well as avoiding the obstacles on its way.
  • Android: Communication between Android application and Master node to pass GPS coordinates and routing details.
Completed
10 11/22/2017 11/29/2017
  • Add additional functionalities and indicators on the car.
  • Integrating RC Car controllers as a single unit. Start with the testing, debugging and optimization process.
  • Make the PCB design for the entire unit. Give extra Vcc and ground pins at the ends for added functionalities like headlights and indicators.
In Progress
11 11/30/2017 12/14/2017
  • Completion of the final Wiki page and the report.
  • Further testing and optimization of the project on campus routes.
In Progress
**************Final Demonstration.*************** To Do

Parts List & Cost

Item# Part Desciption Vendor Datasheet Qty Cost
1 RC Car 1
2 CAN Transceivers MCP2551-I/P Microchip [1] MCP2551-I/P Datasheet 8 Free Samples
3 Sonar Sensor Amazon [2] Maxbotix EZ1 MB 1010 Datasheet 4 $24.95
4 Headlights
5 NiMH Battery From seniors 2
6 Charger for NiMH/NiCd Battery From seniors 1
7 Bluetooth (HC-05) HiLetgo [3] 1 49.0
8 Graphics LCD Display 4D systems [4] 1 49.0
9 SJOne Boards From Preet 4 400.00
10 RPM Sensor Amazon Prime 1 25
11 Magnets From Seniors 15 0.00

Sensor Module

The sensor module refers to the sensors and the embedded board that controls the sensors. In this project we have used four Maxbotix EZ0 ultrasonic sensors. Each of these is mounted in four positions. Three sensors face the front of the car and are positioned in the centre, the left edge and right edge of the car. One sensor is mounted on the back of the car.

The main goal of the sensor module is to detect the distance to an obstacle, from the car and provide this information to the driver module so that it can successfully avoid the obstacle.

MaxSonar Ultrasonar Sensor

Hardware Design

The sensors used are LV-MaxSonar-EZ1 Ultrasonic Range Finder MB1010.

The valid sensors output is a value between 6 and 254. This value is in inches and represents the distance to the obstacle, from the sensor. It is to be noted that if the obstacle is closer than 6 inches from the sensor it will not be detected.

The sensor provides output in three forms; As a pulse on the PW pin, where pulse width represents the distance to obstacle; As an analog voltage on the AN pin; As a digital output on the TX pin, in RS-232 format. We have used the PW pin in this project to receive the input from the sensor.

It is to be noted that if two sensors which are placed so that their beams/detection areas overlap, are ranging at the same time, they cause each other interference and hence incorrect values. Hence we trigger each sensor separately one by one so that at any time, only one sensor is ranging.


Sensor Beam Overlap
Pin connections - middle sensor

Hardware Interface

Pin connections for each sensor is as follows:

PW (Pin 2) - GPIO Pin configured as interrupt to receive input from sensor

RX (Pin 4) - GPIO Pin configured as output to trigger the sensor

VCC (Pin 6) - +5V

GND (Pin 7) - GND

Pin connections for the middle sensor are displayed.


Software Design

Sensor CAN message

As described in the previous section, the sensors are triggered one by one to prevent corruption of data. In our implementation the sensors are triggered in the following order: middle, right, left and back. The back and left sensors are triggered together since they would not interfere with each other.

Every sensor needs a power up time of 250 ms and some time to calibrate and take the first reading. After this period the sensor can provide a reading every 49 ms. In our implementation, all 4 sensor values are taken every 120 ms and put on the CAN bus. The format of the CAN message is shown in the following snippet taken from the DBC file. It can be observed that the sensor message has a high priority since it is critical to the operation of the car.

Implementation

The following steps are followed to get a valid sensor reading.

1. Initialize the sensors - account for power up and calibration delay.

2. Enable falling edge interrupts and setup callback functions - this is to record the pulse width output of the sensor

3. Trigger each sensor and record the current time. This is the start time.

4. When falling edge interrupt occurs record the time. This is the end time.

5. Calculate pulse width using the start and end time. This pulse width would indicate the distance to the obstacle.

Sensor operation flowchart

Testing & Technical Challenges

There were a few difficulties during implementation and testing of the sensors. Lessons learned include the following:

1. Research different types of sensors, find out the strengths and weaknesses of each before making a decision.

2. Ultrasonic sensors need to be slightly tilted upwards when mounted on the car to prevent them from accidentally detecting ground as an obstacle. This becomes especially necessary when testing on a slope/ramp.

3. Ultrasonic sensors are very sensitive and care needs to be taken while soldering them. Accidental overheating can cause them to be destroyed.

4. The ultrasonic sensors provide more range when +5V is used as supply rather than +3.3V.

5. Testing both indoors and outdoors is necessary to check if the sensor readings are accurate in both conditions.

Motor Module

Motor module is one of the five controllers used in our self-driving car. Motor controller is responsible for driving the car forward and for steering the vehicle. The motor module has two motors viz.DC motor and Servo motor. DC motor makes the car move forward and reverse. Servo motor steers the car either left or right. Along with the two motors, we have the rpm speed sensor which is interfaced with our controller to control the speed of DC and move the car at the desired speed in Miles per Hour(MPH).

Team Members

Hardware Design

The Motor Module consists of 2 motors viz. DC motor and Servo motor controlled by an SJOne board by varying the PWM signals, which is nothing but the duty cycle. PWM stands for pulse-width modulation, a type of digital signal and can be used to control the motors.Along with two motors we have interfaced the RPM sensor with the motor module micro-controller to get the wheel feedback and move our car at a constant speed even if the car is going uphill or downhill.

Block Diagram for Motor module

Hardware Interface

Schematic diagram for Motor module with all connections


Servo Motor:
Varying Duty cycle and PWM waveforms according to steering position

RC car came with a digital servo motor, requiring around 3-5V. The motor is directly controlled by giving a varying PWM signal from the SJOne board. Servo motor is used to convert an electrical signal into a linear motion. As per the PWM pulse received by the servo motor from SJOne board, it will rotate its shaft by a certain degree left or right. Below table gives the PWM values given to the motor for turning the car in the desired direction.


No. PWM Direction
1 10.1 Full Left
2 13.3 Slight Left
3 14.7 Very Slight Left
4 15.4 Straight
5 16.1 Very Slight Right
6 17.5 Slight Right
7 19.8 Full Right


DC Motor:
DC motor Traxas#3785_Titan_12T


Like servo motor, the DC motor was also embedded in the RC car. The DC motor is used to convert an electrical signal into mechanical power. DC motor is controlled in the same manner as the servo motor i.e., by varying the PWM signal. The only difference here is that the PWM signal from the SJOne board is given to an Electronic Speed Controller or ESC. The ESC is used to generate three-phase electric power of low voltage in order to vary the speed of the DC motor. In case of no ESC, the DC motor will either not move or will start moving at full throttle. The RC car DC motor required 7.4V of power supply to work. The maximum speed that can be attained by this DC motor is 31mph.

Software Design

Implementation

The following steps

1.

2.

Testing & Technical Challenges

Following were the problems faced and their resolutions:

Problem 1: DC motor would not work unless initialized with the transmitter (remote) before connecting to SJOne board.

Solution 1: DC motor was initialized in init function by passing the neutral command (PWM of 15.4) and giving a delay of 1 second.


Problem 2: RPM sensor was not able to detect the magnet fixed on the wheel.

Solution 2: We had to stack together 3 magnets instead of one so that it was just millimeters away from the RPM sensor as well as its magnetic strength increased to be detected accurately by the RPM sensor.


Problem 3: Speed was not accurate with one magnet on the wheel.

Solution 3: Five magnets at an equidistant position from each other were used for better accuracy. More the magnets, better is the accuracy of speed calculation.


Problem 4: In spite of controlling speed using RPM sensor, the car was not in control while on a downhill.

Solution 4: After trying all possible solutions we could think of, we applied a brake momentarily at the start to reduce the sudden increase in PWM and then controlled the car based on the inclination. Also, made sure that if PWM value went below a certain range, then no brake was applied to the car.


Problem 5: Reverse functionality was difficult to implement.

Solution 5: Forward -> stop = 16.0 (with time delay) and then reverse using PWM = 15.3. Neutral PWM = 15.4


Problem 6: The car did not go reverse all of a sudden even with the working code.

Solution 6: When checked with the transmitter/remote, still didn't work. It was found by reading the manual that ESC has 3 modes which can be set by long pressing the power button. And accidentally, ESC was changed to mode 2 where reverse wouldn't work. Car was set back to Mode 1.


Problem 7: Servo and DC motors didn't move even in open surroundings with no obstacles or MIA condition at one instance.

Solution 7: It was found that the Bluetooth start button was disabled from the Android application.

Geographical Controller

The geographical Controller is responsible for navigating the car in the direction of the destination selected by an android user. It uses a compass module for getting the heading angle with respect to the North and a GPS module which returns the current location of the car. After a particular destination has been chosen from the android app, the bridge module generates a number of checkpoints according to the shortest path algorithm. These are then sent to the geographical controller one by one. Using each of them, the bearing angle and the distance between the car and the checkpoint is calculated. Subsequently, the angle that the car should turn is determined and sent to the master module. On reaching the destination, the car is stopped.

Hardware Design

The Geographical controller makes use of the following two modules:

GPS

Venus638FLPx GPS Receiver

Venus638FLPx is used for detecting the location of the car. It returns the NMEA GPS string which needs to be parsed to get the latitude and longitude values from the module. It is a high performance, low cost, single chip GPS receiver that offers very low power consumption, high sensitivity, and best in class signal acquisition and time-to-first-fix performance.

Features:

 20Hz update rate
-148dBm cold start sensitivity
-165dBm tracking sensitivity
29 second cold start TTFF
1 second hot start
2.5m accuracy
67mW full power navigation
Works directly with active or passive antenna


COMPASS

CMPS11

CMPS11 tilt-compensated compass module is employed for getting a heading angle value between 0-359. It requires a power supply of 3.6-5V. It can be interfaced via both serial(UART) and I2C. We have incorporated the I2C interface in which the 'mode' pin of the compass is left unconnected. It has a 28-byte array of registers and compass bearing can be read from 8-bit register 1.

Calibration of CMPS11 - We are using switch 1 and switch 2 of the SJOne board for entering and exiting the calibration mode respectively. When switch 1 is pressed, a 3-byte sequence of 0xF0, 0xF5 and 0xF6 is sent to the command register 0 and an led on the module starts blinking indicating the calibration mode. Compass is then slowly rotated in all 3 dimensions to get both negative and positive maximums. Only after the led completely extinguishes, switch 2 is pressed and 0xF8 command is sent to exit the calibration mode. More accurate readings can be achieved by performing calibration meticulously.

Hardware Interface

Schematic diagram

UART :

Pin connections for GPS is as follows:

VCC (Pin 1) - +5V

TX (Pin 2) - RX

RX (Pin 3) - TX

GND (Pin 4) - GND

I2C:

Pin connections for compass is as follows:

VCC (Pin 1) - +3.3V

SDA (Pin 2) - SDA

SCL (Pin 3) - SCL

GND (Pin 6) - GND

Software Design

Flowchart

GPS Module flowchart

Algorithm

STEP 1: Read data from GPS sensor through UART and parse the string to get latitude and longitude of the current location.

STEP 2: Read satellite count from the GPS sensor to enable GPS lock.

STEP 2: Get heading angle from compass through I2C, compass can be calibrated on pressing switch 3 and 4 at the same time and can be stopped on pressing switch 1.

STEP 3: Sending GPS heartbeat message on CAN bus to master, so that master knows that GPS module is connected.

STEP 3: Receiving destination location message on CAN bus from bridge controller.

STEP 4: Computing bearing angle from the current and destination locations obtained.

STEP 5: Sending the current location latitude and longitude obtained, to bridge controller on CAN bus.

STEP 6: Sending the bearing angle, heading angle and GPS lock enable in one message to the bridge controller through CAN bus.

STEP 7: Computing the distance between the current location and the destination location.

STEP 8: If obtained distance is less than 5 meters then a message is sent to master as well as bridge controller, so that bridge controller can send the next checkpoint.

STEP 9: If all the checkpoints are done then that is the final destination, and bridge controller will not send any new location, so master should stop the car on receiving the car arrived message.

STEP 10: Finding the difference between heading angle and bearing angle, and realizing how much does the car should turn to navigate towards the destination.

STEP 11: Sending a car turn direction message to the master module, so that master module sends the message to motor module to set a pwm frequency, depending on the message sent, to turn the car.

Implementation

Formulae used:

On obtaining the current latitude and longitude position, and destination latitude and longitude position should be determined from CAN message sent by bridge (bluetooth) module. Bearing angle has to be computed from the obtained current location and destination location.

Bearing angle - Bearing angle is the angle between the direction towards the destination from the current location with respect to north. The bearing angle range is form 0 to 359.

Both bearing and heading angle’s should have the same range, can be from -180 to +180 or 0 to 360, we are using 0 to 360.

Bearing Angle Computation

Degrees - We need to compute the angle that the car has to turn from its current direction towards the destination, from the obtained obtained bearing angle(angle at which the car should go with respect to north to reach the destination) and heading angle (angle at which our car is going currently with respect to north).

Degree = Heading angle - Bearing angle

Degrees calculation

Depending on the degree, the car’s front wheel servo motors are to be turned accordingly. The turn direction messages to the master and their corresponding interpretations are as shown in the figure.

Turn direction messages

Distance Caluculation-

Distance between current location to destination


Testing & Technical Challenges

Problem 1: GPS usually takes a long time to get the fix.

Solution 1: The GPS module should be operated in hot start mode wherein an external battery(VBAT) of 3V is connected to it.


Problem 2: There was significant delay(5-10 seconds, approximately) in the getting the latitude and longitude values while the car is moving.

Solution 2: The receive queue/buffer size of UART should be kept minimum.


Problem 3: The compass values were inaccurate.

Solution 3: The calibration needs to be done with a lot of patience. Also, it should be positioned as far away from magnets(GPS antenna and RPM sensors) as possible which can easily generate erroneous values from it.

Communication Bridge Controller & LCD

The purpose of Communication Bridge Controller is to establish communication between Andriod app and Car via bluetooth communication protocol. This ECU send the updated checkpoints to Geo Controller at a particular instance when the car reaches at one checkpoint and sends the current location of the car to Android phone so the tracking of the car on-road becomes easy. The Communication Bridge Controller also displays the Current location, Sensor readings, Car Speed on graphics LCD.

Hardware Design

This section highlights the hardware components used. The components used are SJOne board, Bluetooth, Gen4-uLCD-32PT (graphics LCD).

HC-05 Bluetoooth module
HC-05 Bluetooth

Used HC-05 Bluetooth modem to establish wireless communication between the car and the Android phone. This module is based on the Cambridge Silicon Radio BC417 2.4 GHz BlueTooth Radio chip. This is a complex chip which uses an external 8 Mbit flash memory It includes the Radio and Memory chips, 26 MHz crystal, antenna and RF matching network. The right section of the Bluetooth Board has connection pins for power and signals as well as a 5V to 3.3V Regulator, LED, and level shifting.

  • HC-05 PinOut :
    • EN: In case brought HIGH before power is applied, forces AT Command Setup Mode
    • VCC: +3.3V Power
    • GND: Ground
    • TXD: Serial Transmit pin connected to RXD2 of SJOne board
    • RXD: Serial Receive pin connected to TXD2 of SJOne board
    • STATE: States if connected or not
  • LED Blinking signals:
    • if flashing RED fast: ready to pair
    • if flashing RED slow: paired and connected
Gen4-uLCD graphics LCD
Graphics LCD from 4D systems

This project uses gen4 3.2” Picaso Integrated Display Module by 4D Systems. This LCD comes with resistive touch. It is powered by the well-known 4D Systems Picaso Graphics Processor, which offers wide range of functionality and options for any Designer/Integrator. We have used Workshop4 IDE and its Visi-Genie development environment for interfacing the LCD with Controller.

Specifications and Features

  • 4.0V to 5.5V range operation (single supply)
  • Maximum current sunk/sourced by all ports- 200.0mA
  • The Picaso processor features include 13 customisable GPIO, 2 Serial ports, and a Master I2C interface.
  • The 3.2” Picaso Integrated Display Module features a TFT LCD Display, is capable of Touch Detection, microSD memory Storage, GPIO and Communications, along with multiple millisecond resolution timers, and Audio Generation.
  • 14KB of Flash memory for User Application Code and Data
  • 2 x Asynchronous hardware serial ports (COM0, COM1), TTL interface, with 300 to 600K baud.
  • 1 x I2C interface (Master).
  • 8 x 16 bit timers with 1 millisecond resolution.
  • 13 x General Purpose I/O pins. Supports fast 8-bit parallel data transfer through Upper 8 bits.
  • 30pin FPC connection, for all signals, power, communications, GPIO and programming.
  • On-board latch type micro-SD memory card connector for multimedia storage and data logging purposes.
  • DOS compatible file access (FAT16 format) as well as low level access to card memory.

Hardware Interface

Communication Hardware Interface

The Communication Bridge Controller is the interface of communication between user and the car. The ECU is interfaced with Bluetooth via UART and with graphics LCD via UART. The Communication Bridge Controller displays the messages on LCD. This section details the designs of the hardware components used for the communication and display. Android app routes the car.


Software Design and Implementation

Communication Process Flow Diagram

Algorithm Design

  • Step 1: Initialize the CAN controller, UART2 for Bluetooth communication, UART3 for graphics LCD, setting appropriate queue size for the UART and CAN communication.
  • Step 2: For UART2, read the characters from the queue to decode the type of value. The string type is indicated by the starting character.
  • Step 3: Convert the string to appropriate message, and store correctly. So after the conversion the value can be either START_STOP, CHECKPOINTS_COUNT or LATITUDE_LONGITUDE.
  • Step 4: For the simplicity before reading the checkpoints the START_STOP bit is set to Zero and after reading all the checkpoints the START_STOP bit is set to One to Start the Car.
  • Step 5: The car is running now to reach to the first checkpoint values. As the Car reaches in the suitable range of the location, the Communication Bridge ECU sends next checkpoint. Otherwise it keeps on transmitting the checkpoint yet to reach.
  • Step 6: Parallel with the wireless communication. The UART3 queue is getting the messages from CAN bus.
  • Step 7: Calculate the checksum of the messages to display on LCD and Display important values like CURRENT_GPS_LOCATION, CAR_SPEED, GPS_BEARING, GPS_HEADING_ANGLE, DISTANCE_to_Destination, and CAR_TURN_ANGLE_Direction.


Testing & Technical Challenges

1) The first problem we had was to read the data from queue. Some part of actual transmitted data from Android phones was not at all received in the queue. So we changed the timeout value and handled the newline character while reading data.

2) The second issue we had was that our START_STOP bit were dependent on the validate and store function which if the START_STOP bit was not received, the default value of zero was passed on the bus and that falsely stopped the car. So we transmitted the START_STOP bit only when we receive it, and not otherwise.

3) Graphics LCD did not display data correctly. So we figured out that we have to compute the checksum of the data and other related information to correct readings on the display.


Master Module

The master module is the driver which is responsible for the smooth navigation of the car. It accepts all the inputs from sensors, the geo controller, the android app and makes a decision to drive the car according to this data received.

Hardware Design

The objective of the master module is to make the car reach the destination location via all the checkpoints given by the android app with the help of geo-controller. On its way to the destination, there may be obstacles in the path of the car which it should avoid at all times. The flow of the CAN messages is as shown below

CAN Messages Flow



















Hardware Interface and Pin Connections

One SJ One board is used as a master controller. These boards have the following connections:

  • CAN receiver and transmitter connections.
  • Headlights and Taillights for the car.
  • VCC and GND connections.
Pin Number Connection Details Description
P 1.20 Front LED Headlights of the car
P 1.22 Rear LED Taillights of the car
P 0.1 CAN TXPin Connected to pin 7 of MCP2551
P 0.0 CAN RXPin Connected to pin 6 of MCP2551
GND Connected to common ground
3V3 Connected to incoming supply voltage All the VCC are commong, coming from 5V battery supply.
Hardware Design Master Module






























Software Design

The software flow of the master module is as shown in the following image. Let's get a brief idea of how it made,


Master Module Software Flow Chart.png

Implementation

The software is made up of 3 main modules.

  • Obstacle Avoidance
Obstacle avoidance algorithm takes care of all the obstacles and moving direction of the car. Obstacle avoidance sends signals to move the car in a certain direction.
  • Motor Commands Generator
  • Indicators Controller

Overview of modules

Obstacle Avoidance
Obstacle avoidance algorithm is the essence if the driver module. It takes care of all the obstacles that come in between the path and avoids the car from colliding or hurting someone.
Some properties of the obstacle avoidance algorithm,
  • It uses a total of 3 sensors mounted at the precise angle on the car to detect obstacles that come in the front and 1 sensors for the rear of the car.
  • Whenever all the front sensors senses an object in the middle it will keep on taking reverse with a left astern until the front is clear.
  • When all the 4 sensors sense an object at the same time, the car will not move as there is no space for it to move.
  • The priority for operation between all the modules is highest for obstacle avoidance.
  • Obsatcle avoidance doesn't move the car at all when:
  • There is a stop signal from the android app forcing the car to stop
  • The destination is reached.
  • Bluetooth, GPS, and Sensor modules are not on the CAN
Let's peek more into the working of obstacle avoidance algorithm,
Obstacle avoidance algorithm is written based on the following state diagram. It keeps on checking the center sensor at the beginning. If the center sensor is sensing an object there is no way we can go further as the car may collide with an obstacle if it detects an obstacle. So, in this case, the car will check whether there is an object in the back or not if the back is also blocked the car will stop at the position. If the rear is not blocked it will take reverse until the front is unblocked. If the center direction is not blocked it will go straight in this case and keep on checking side sensors, if any one of the direction is blocked it will move in the opposite direction. If both the side sensors are blocked then the car will go into reverse condition as it does not have any front direction to go. If the rear is blocked during this operation the car will be stopped at that position, and if not it will take reverse until font direction is clear. If none of the direction is blocked it will always follow the GPS directions sent by GPS module.


Obstacle Avoidance Flowchart.


Motor Commands Generator
This module is responsible for sending all the actions taken by obstacle avoidance to the motor.
It sends following commands to the motor module at the execution of the obstacle avoidance algorithm.
  • Angle at which the car should move
  • Driving speed at which the motors should be driven
  • Direction in which the car should go(Reverse or Forward)
It frames this messages into a structure and sends to the motor to take control accordingly.
Indicator Controller
This module is responsible for controlling all the lights mounted on the car. The car has 2 head lights and 2 tail lights.
All the indicators are updated in 100ms periodically
Opearation of these lights are as following
Head Light Tail Light Car State
On Off Going Forward
Off On Stopped
Off Blinking Going Reverse
Blinking Blinking Reached The Destination

Testing & Technical Challenges

Android Application

A GoogleMap-based Android application was developed to provide the required information to our self-navigating car, Alpha to reach destination. The information includes the routing information between the source and the destination as well as a software-based command to start and to stop the car. This application also displays information regarding the current position and heading angle of Alpha.

Hardware Interface

Image of Interface between android app and bluetooth module is as shown. Bluetooth Module part hase explained it in detail.

Interface between android and bluetooth module on car

Software Design

1. Bluetooth: Bluetooth allows to wirelessly exchange data with another Bluetooth device. Here, we are using Bluetooth to communicate our self-driving car with our Android application.

1.1. Enable Bluetooth: Bluetooth in the phone programmatically enabled using BluetoothAdapter. If Bluetooth in the phone is not enabled, then it can be enabled from the application.
1.2. Connect to Bluetooth on Car: A new Socket was created using UUID of Bluetooth device on Alpha. A connection request is sent by calling a connect method created on the socket. Here, "Connect" is the blocking call which will return if the connection request is accepted and the connection is established or an exception will be thrown. To establish an automatic connection between Alpha and the mobile device, a separate thread was created which will continuously check the connection and try to make a connection in case Bluetooth on car is not connected. A connection indicator shows the current connection status.
Heading angle and location indicator
1.3. Read from Alpha: Read the data from input-stream and convert it into accurate latitude, longitude, and heading angle. A separate thread is used to continuously read data and update it on the screen.
1.4. Write to Alpha: Write the data in the output stream so that it can be available to Alpha. In this application Start bit, Stop bit and the routing checkpoints are sent to move the car.

2. Routing Algorithm: Dijkstra Routing Algorithm is used to calcite shortest path algorithm between source and destination. Check points are taken inside San Jose State University. Latitude and Longitude of each check point is considered as a node of directed graph. The routing path is stored as an array of check points and sent to car using Bluetooth. On map the routing is shown by blue line which connect to all check points. All check point between source location and destination location is shown by violet colored markers, source location is shown by blue marker and destination is shown by red marker in routing path.

3. Start and Stop: Command to start the car and stop the car provided by android aplication. Here, for both command a single button is used as start and stop are alternative activity. Once car is started by pressing on "GO" button on aplication, the button on app will convert in "STOP" button. A voice command indication is provided to Start and to stop.

Implementation

Algorithm:

PREREQ: All possible checkpoints should be previously saved in the app before the routing algorithm is run. This is a one-time activity.

1. Check Bluetooth Status

a. If Bluetooth is not enabled
Enable Bluetooth.

2. Fork a child thread for automatic connection to the car’s Bluetooth module.

3. Fork a child thread to read data from the car continuously through the Bluetooth connection.

4. Get the Destination from ‘On click’ method on map.

5. On clicking on Go Button

a. If Bluetooth connectivity lost
Error: Car is not connected to Bluetooth
b. Else If Destination is not selected
Error: Destination is not selected
c. Else
I. Get current location latitude and longitude and save as source.
II. Calculate routing path using Dijkstra routing algorithm.
III. Send all check points to car using Bluetooth.
IV. Send start message to car using Bluetooth.

6. On clicking on Stop Button send stop message to car using Bluetooth.


Algorithm For Automatic Connection Thread:

1. If Connection to car is available go to sleep.

2. Else

Delete Old socket.
Create new socket and send connection request to connect.
Go to sleep.

3. Repeat step 1 and 2 till app is destroyed.


Algorithm For Read data From Bluetooth Continuously:'

1. Read data from Bluetooth buffer.

2. Convert data to Current Location and Compass Angle.

3. Display Current Location and Compass Angle on the Display Screen.

4. Repeat Step 1 to Step 4 till app is not destroy.

Flowchart :

 Flowchart.
Flow chart for Android Application.

Testing & Technical Challenges

1. Automatic connection to bluetooth: In case of bleutooth connectivity lost, while trying to reconnect using same Socket was not conncting to Bluetooth again.

Solution : If connection lost between Android app and bluetooth a new Socket should create and try to connect using newly created socket. As, now old socket is not used delete old socket.

2. Routing Algorithm: There are many shortest path algorithm available which move from one check point to another check point in the map.(Logically all points in the map cannot be check points.) In the application current checpoint and destination may not be from the check point which are taken.

Solution : make algorithm to find nearst check point from the source towards the destination and connect source node to this check point. In same manner, Find nearest check point from Destination towards source and connect destination to this check point. Calculate sortest path between these two check point using Disktera's algorithm.

3. Adding Check points: Check point taken by normal view of google map were not accurate.

Solution: All the check points taken using satellite view of google map and accuracy confirmed by reading of GPS used by car.

Conclusion

We were able to successfully navigate our car to the destination marked in our Android application by avoiding any obstacle in its path. This project gave us a real-world project experience. It helped us gain a working knowledge of CAN bus and communication, interfacing various components such as motors, GPS, Bluetooth and ultrasonic sensors along with some knowledge regarding pulse width modulation (PWM), UART, I2C. We also gained knowledge of freeRTOS, Android, Unit testing and Git. We faced many hardware and software issues, especially while integrating each new module into the existing working solution. In all, it has been a great experience watching our work slowly come together and seeing our RC car avoid all obstacles and move from source to destination.

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learned from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

Git Link - ALPHA

Acknowledgement

We would like to thank our professor, Preetpal Kang for designing such a course where learning was his guidance and consistent feedback. We would also like to thank the ISA team for their valuable inputs as per their own experience of the course when taken and their support and motivation at every phase of this project. There were some unsung, selfless classmates who helped us whenever necessary, whenever any immediate hardware was required or any other guidance needed in spite of being from the rival teams. We would like to thank each one of them who forgot their differences or considered the course and project as a competition to selflessly help us when in need.

References

[1] Preetpal Kang's lecture notes of CMPE 243, Computer Engineering, San Jose State University, Aug-Dec 2017.

[2] Routing Guide

[3] Android Development Guide

[4] Traxxas - RC Car & Forum