F16: Piano Glove

Grading Criteria

• How well is Software & Hardware Design described?
• How well can this report be used to reproduce this project?
• Code Quality
• Overall Report Quality:
  • Software Block Diagrams
  • Hardware Block Diagrams

    Schematic Quality

  • Quality of technical challenges and solutions adopted.

Project Title

OVS: Piano Glove

Abstract

The Piano Glove is a device that is capable of synthesizing the notes of a Baby Grand Piano.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

Melissa Ortiz

• Full System & PCB Design
• Digital Signal Processing in MATLAB
• Device Driver Implementation
• System Integration, Verification, and Validation Testing

Benjamin Vuong

• Algorithm Development
• Device Driver Implementation
• System Integration, Verification, and Validation Testing

Schedule Overview

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Week #	Start Date	End Date	Team Task Description	Status	Actual End Date
1	10/14/16	10/21/16	Research Design Approach and Assign Tasks	Complete	10/21/16
2	10/21/16	10/28/16	Set up Version Control and Research Parts	Complete	10/28/16
3	10/28/16	11/4/16	Discuss MCU Responsibilities and Communication	Complete	11/4/16
4	11/4/16	11/11/16	Purchase Parts and Begin Prototyping	In Progress	11/11/16
5	11/11/16	11/18/16	Status Update: Demo First Round of Prototyping	N/A
6	11/18/16	11/25/16	Interface Modules and Perform System Design Verification/Validation Testing	N/A
7	11/25/16	12/02/16	Continue Validation and Optimize System	N/A
8	12/02/16	12/20/16	Finalize Design and Prepare for Demo	N/A

Parts List & Cost

Give a simple list of the cost of your project broken down by components. Do not write long stories here.

Item #	Part Description	Vendor	QTY	Cost (USD)
1	SJSUOne Board	Preet	1	$80
2	Flex Sensor	Mouser	10	$6.45
3	MCP4822-E/P DAC	Mouser	10	$3.06
4	MCP6242-E/P OPAMP	Mouser	10	$0.36
5	Gloves	Nike	1	$12.99
6	Misc Parts (Wires, Resistors, etc)	Personal	N/A	Free

Hardware Design & Interface

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Schedule

Discuss your hardware design here. Show detailed schematics, and the interface here.

Week #	Start Date	End Date	Description	Status	Actual End Date	Comments
1	10/21/16	11/4/16	Research Design Implementation and Brainstorm PCB Schematic Layout Determine and Purchase Parts	Completed	11/4/16
2	11/4/16	11/11/16	Design and Interface Schmitt Trigger Circutry w/SJSUOne Board Create PCB Schematic	Completed	11/11/16	PCB design is not complete, we are not sure that it is necessary.
3	11/11/16	11/18/16	Sew Flex Sensors onto Gloves and Interface w/Development Board Send PCB out for fabrication Status Update: Demo First Round of Prototyping	In Progress		Sewing the sensors onto the gloves was tedious. The sensors are very fragile, so they had to be handled with caution.
4	11/18/16	11/25/16	Interface Modules and Perform System Design Verification/Validation Testing	N/A
5	11/25/16	12/02/16	Continue Validation and Optimize System	N/A
6	12/02/16	12/20/16	Finalize Design and Prepare for Demo	N/A

Hardware Development

System Block Diagram

The following diagram is a high-level overview of our system. It is depicts the general structure of our design. In addition to that, it also demonstrates a generalization of the major system components that were used as well as their relationship among each other.

Schmitt and Trigger

The Schmitt and Trigger circuit is used to convert the Analog Output of the Flex Sensors into a Digital Signal. This Analog to Digital Conversion (ADC) is done so that the SJSUOne MCU can interpret the input signal using a GPIO port.

Design Choice: we decided to create our own ADC circuit because of the limited availability on the SJSUOne board. There are simply not enough ADC pins to perform our task, as we would need 10 ADC pins.

Datasheets

• 12-Bit DAC
• MCP624 Operational Amplifier
• Spectra Flex Sensor

System Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design & Implementation

Software Schedule

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Week #	Start Date	End Date	Description	Status	Actual End Date
1	10/21/16	10/28/16	Research the following: Algorithm Design/Implementation and Digital Signal Processing in MATLAB	Complete	10/28/16
2	10/28/16	11/11/16	Develop Algorithm and Device Drivers as well as Incorporating RTOS	In Progress
3	11/11/16	11/18/16	Status Update: Demo First Round of Prototyping	In Progress
4	11/18/16	11/25/16	Implement Code w/Integrated Unit and Begin Debugging As Necessary	N/A
5	11/25/16	12/02/16	Continue System Integration Testing for Validation and Optimization	N/A
6	12/02/16	12/20/16	Finalize Design and Prepare for Demo	N/A

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Integration Testing, Results, & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

Hardware

My Issue #1

• Initially we had ordered the wrong parts. Due to time constraints, we rushed selecting parts and were not careful on selecting the components that had the right packaging. Therefore, we ended up purchasing MSOPs (Mini-Small-Outlined-Package) instead of PDIPs (Plastic Dual Inlined Package). Using MSOPs would not work for us because the IC was simply too small to work with. It would not be able to fit on our breadboard for prototyping purposes.

For more information on IC Packaging and Dimensions, please refer to this link: IC Package Dimensions

Oscilloscope Readings

My Issue #2

Discuss the issue and resolution.

Software

DSP Simulations

My Issue #2

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

• Sourceforge Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

• Commuted Piano Synthesis
• Piano Sounds Synthesis
• The Gloves Project
• PHL Gloves

Appendix

You can list the references you used.