Difference between revisions of "F21: ACE MARIO"

From Embedded Systems Learning Academy
Jump to: navigation, search
(References Used)
Line 1: Line 1:
  
[File:13.jpg|center|500px|thumb|ACE MARIO GAME]
+
[[File:13.jpg|center|500px|thumb|ACE MARIO GAME]]
  
 
== Project Title ==
 
== Project Title ==
Line 628: Line 628:
  
  
Graphics Designing
+
Image Designing
  
 
* [http://mtpaint.sourceforge.net/ Mtpaint Source & Documentation]
 
* [http://mtpaint.sourceforge.net/ Mtpaint Source & Documentation]

Revision as of 04:36, 18 December 2021

ACE MARIO GAME

Project Title

Ace Mario

Abstract

Super Mario is one of the best-selling games of all time, with more than 50 million copies sold worldwide. Our goal will be to produce a similar version of it where the player controls Mario. Mario has to race through the Mushroom Kingdom and save Princess.

Objectives

The main objective of this project was to create a Mario video game displayed on an RGB LED matrix. We used two SJ2 boards. One for graphics processing and, the other SJ2 board was used as a gamepad controller, which controller the graphics board and sends data to the LED matrix board. Other objectives are as follows:

  • Use the FreeRTOS Real-Time operating system on both the SJ2 boards.
  • Interface the 64*64 RGB LED Matrix and MP3 decoder on one of the SJ2 boards.
  • Interface Joystick, vibration sensor, bluetooth on the other SJ2 board.
  • Establish wireless communication between these two nodes using bluetooth.
  • Create and display characters on the LED matrix.
  • Create different sound effects at different functions of the game.
  • Create multiple display screens at different stages of the game.
  • Intergrate all the modules and develop smooth game logic.

Introduction

This project was divided into two SJ2 nodes. Each node had its own function as described below:

  • LED Matrix controller board:




  • Game Pad Controller:




How to Play ACE MARIO







Team Members & Responsibilities

Name Roles / Responsibilities
Vivek Tapkir
  • Collision Detection
  • Game Logic Developer
  • LED Matrix Driver
  • Hardware Integration
Shreevats Gadhikar
  • Game Logic Developer
  • Bluetooth and Joystick Driver
  • Hardware Integration
  • PCB Design
Daya Modekar
  • MP3 Decoder Driver
  • Game Logic Developer
  • Graphics Driver
  • Hardware Integration

Schedule

Week# Start Date End Date Task Status
1
  • 10/15/2021
  • 10/25/2021
  • Read previous projects, gather information and discuss among the group members.
  • Decide on 2 game ideas and submit Project Proposal assignment
  • Discussion on using wireless or wired controllers,3D printing options,PCB softwares and manufacturer.
  • Finalize parts list
  • Setup splitwise account for cost sharing
  • Create GitLab repository for project
  • Decide on day/time for weekly meetings
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
2
  • 10/25/2021
  • 11/03/2021
  • Choose game based on Preet's Project Proposal feedback
  • Finish schedule rough draft and upload to Wiki report
  • Order project parts
  • Break project up into tasks and assign project tasks to team members
  • Obtain datasheets for all parts and upload to team Google Drive folder
  • Brainstorm gameplay, rules, and level design on paper
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
3
  • 11/04/2020
  • 11/08/2020
  • Read and familiarize with LED Matrix Datasheet
  • Read datasheets and conduct research for driver writing
  • Finalize wiki schedule
  • Test all parts to ensure proper functionality
  • LED matrix can light a pixel(s) at specified locations.
  • Finalize gameplay, rules, and level design on paper
  • Start Developing graphics driver for LED matrix and implement initial game objects
  • Begin developing MP3 decoder board driver
  • Begin designing PCB in EasyEDA software
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
4
  • 11/09/2021
  • 11/15/2021
  • Begin developing Bluetooth board driver
  • LED matrix can display our game character and obstacles
  • MP3 decoder can play/pause, jump to next/previous song, and increase/decrease volume
  • Bluetooth modules can send controls data back and forth between gamepad board and master board
  • Controls data can be accessed using "get" and "set" API
  • Gamepad controller can read joystick and accelerometer values and detect switch presses
  • Decide how to handle each collision detection case (character/enemy, obstacles/enemy, etc.)
  • Finish enclosure design in AutoCAD software and start printing
  • Finalize PCB design on paper and design in PCB software
  • LED matrix displays character orientation correctly depending on current movement direction
  • Controller input (joystick or accelerometer) option is implemented on a gamepad controller
  • Finalize PCB design in software and order PCB
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
5
  • 11/16/2021
  • 11/22/2021
  • LED matrix menu screens and game over/victory screens are implemented on matrix
  • Volume controls and controller input select in the options menu are implemented
  • Integrate circuitry with 3D printed enclosure
  • PCB arrives, conduct PCB testing to ensure proper connections
  • Solder PCB and integrate with existing project circuitry
  • LED matrix can scroll to next screen when the character reaches the bottom of the current screen
  • Finalize MP3 track selection for each screen and during gameplay
  • Collision detection logic is fully functional and displays correctly on the LED matrix
  • Testing and debugging the game logic
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
6
  • 11/23/2021
  • 11/29/2021
  • Integrate game logic code with LED matrix
  • Write gameplay logic code on the master controller. Gameplay logic should update the score and status bar items correctly
  • LED matrix graphics design for all levels is complete
  • MP3 decoder plays correct song/track during gameplay and for each menu/game over screen
  • Integrate game sounds with game logic
  • Completed
  • Completed
  • Completed
  • Completed
  • Completed
7
  • 11/30/2021
  • 12/06/2021
  • Sub-system Integration
  • Finish rough draft of project report
  • Finalizing the video game
  • Completed
  • Completed
  • Completed
8
  • 12/07/2021
  • 12/13/2021
  • Address bugs during testing of an integrated system
  • Test pause/play functionality
  • Completed
  • Completed
9
  • 12/14/2021
  • 12/16/2020
  • Final Demo
  • Update Gitlab repo with final code.
  • Finalize project report and submit
  • Completed
  • Completed
  • Completed


Parts List & Cost

General Parts

Item # Part Vendor Qty Cost
1 64x64 RGB LED Matrix Adafruit 1 $54.95
2 SJ-2 Boards SJSU 2 $100.00
3 HC-05 Bluetooth Boards Amazon 2 $20.00
4 MP3 Decoder/Player Board Amazon 1 $6.99
5 Joystick Amazon 1 $4.89
6 Power Supply for LED Matrix (5V 5A) Amazon 1 $15.99
7 JBL Speakers already had 1 $0
8 Audio Jack Cable already had 1 $0
9 MicroSD Card & Adapter already had 1 $0
10 Vibration Sensor Amazon 1 $10.99

Design & Implementation

Hardware Design

For our project, we choose EasyEDA online software for designing the PCB. EasyEDA is completely free to use and all the footprints are easily available online. Also, EasyEDA has a feature of auto-routing which is very useful. The most important thing about EasyEDA is its ability to create a PCB from schematics.


LED Board PCB Schematic


Game Board PCB Schematic


Game Pad PCB (Front)
Game Pad PCB (Back)

We checked our schematics several times. We also manually checked the footprints for each part before ordering the PCB.

Fabrication

Using the EasyEDA we designed a 2 layer PCB. PCB was sent to fabrication to JLCPCB China which provided PCB within 7 days with MOQ of 5. The dimension of the 1st PCB was 8.5cm * 8 cm while the other was with the dimension of 16cm * 11.5cm. All the components were mounted as close to each other as possible to minimize the PCB dimensions.

PCB Properties: Size: 8.5cm * 11.5cm and 16cm * 11.5cm
Signal Layers: 2
Componenets: 16
Routing width: 0.254mm
Track Width: 1mm
Clearance: 0.3mm
Via diameter: 0.61mm
Via Drill Diameter: 0.31mm
Vias: 20


LED Board Final PCB
Game pad controller



LED Matrix


MP3 Decoder

The MP3 player device which is based on a high-quality MP3 audio chip -YX5300 is used in our project to play different soundtracks based on the current state of the game such as jump, victory, game over and Mario run states. Our master controller unit (sjtwo-c board) controls MP3 playback state by sending commands to serial MP3 via UART port

Serial MP3 Module

Hardware Design

The MCU controls the device playback by sending serial commands through a TTL level UART control interface (GND, VCC, TX, RX). Sound is output through a headphone jack to headphones or an external amplifier. The board has a playback indicator led that blinks during playback and is steady otherwise. The TF card socket on the PCB reverse is for plugging in the micro SD card with mp3/wav files. The micro SD card should be formatted as fat16 or fat32 and songs must be prefixed with a unique 3 digit index number (for example, 001xxx.mp3, 002xxx.mp3, 003xxx.mp3, etc, where xxx is an arbitrary optional name). The baud rate required for communication is 9600 bps. This decoder also contains an audio jack to connect headphones or speakers.

Hardware connection between SJ2 and MP3 Decoder
Hardware support

Software Design

The SJ2 board initializes UART for communicating to the MP3 decoder and allocates memory to load packet information before sending via TX line.Different song tracks were played depending on the game state for example victory song when the players wins, super Mario theme song else where.

In the project, we wait for an event, such as entering the title screen or game to start playing music.

MP3 Decoder flowchart

Below, are snippets of the code used to set up the commands and send them through UART. Before sending any other command, we must command the decoder to select device 2 (as described in the datasheet). A command we used in our ace Mario project was to play the song at index. The function that sends this command is called mp3_decoder__play_song_at_index(). Within commands, there are two function calls for setting up the packet (set_command_and_data()) and the other for sending the packet over UART (send_command_via_uart()) as shown below

static void intialize_command_message(mp3_decoder__msg_t *mp3_decoder_message) {
  mp3_decoder_message->mp3_decoder_command_byte.start_byte = cmd_start;
  mp3_decoder_message->mp3_decoder_command_byte.version_byte = version;
  mp3_decoder_message->mp3_decoder_command_byte.data_length = cmd_length;
  mp3_decoder_message->mp3_decoder_command_byte.feedback_byte = no_feedback;
  mp3_decoder_message->mp3_decoder_command_byte.end_byte = cmd_end;
}

static void set_command_and_data(uint8_t command, uint8_t data_0, uint8_t data_1) {
  mp3_command_message.mp3_decoder_command_byte.command_byte = command;
  mp3_command_message.mp3_decoder_command_byte.data_byte0 = data_0;
  mp3_command_message.mp3_decoder_command_byte.data_byte1 = data_1;
}


static void send_command_via_uart(void) {
  uint8_t i = 0;
  while (i < 8) {
    if (uart__polled_put(uart, mp3_command_message.mp3_decoder_command.bytes[i])) {
      i++;
    }
  }
}

static void select_storage_device(void) {
  static const uint8_t device = 0x02;
  set_command_and_data(mp3_decoder__select_device, no_data, device);
  send_command_via_uart();
}

void mp3_decoder__play_song_at_index(uint8_t index) {
  set_command_and_data(mp3_decoder__play_at_index, no_data, index);
  send_command_via_uart();
}

Bluetooth Interface

For this project, we used two HC-05 Bluetooth modules. One Bluetooth was configured on the LED matrix controller board while the other was configured on the gamepad controller. The Bluetooth configured on the led matrix controller worked as a slave, only receives commands, while the one configured on the gamepad worked as master, sending controls to the other controller. The master Bluetooth connected to the gamepad controller transmitted the joystick direction. The transmitted direction was in the form of x and y coordinates. The UP and FORWARD direction was calibrated using the x and y coordinates. So along with UP and FORWARD direction, the joystick switch button data was also transmitted using Bluetooth.

We selected the HC-05 Bluetooth module to transmit data over other modules because of their ease to configure, they are extremely reliable and also easy to set up. Both the Bluetooth modules were configured using AT commands. Using AT commands made our job easy to set one Bluetooth as a master while the other as a slave. The best thing about using AT commands is that we can change the configuration as per our needs. The UART baud rate was set to 38400.


HC-05 Bluetooth Module

Hardware Design

The HC-05 Bluetooth module was connected to both boards using the SJ2 pins. The pins used were P0.0 and P0.1. These Bluetooth modules communicate with each other over the UART interface. The gamepad controller board process the joystick signals to UP and FORWARD and also the button press and then sends them to the Bluetooth module via UART.


HC-05 Bluetooth Module to SJ2 Connections


Software Design

The following function "receive_from_bluetooth" was used to receive data from the Bluetooth.

void receive_from_bluetooth (void *p) {
 char bluetooth_command_received[50];
 bluetooth_command_received[0] = '\0';
 while (1) {
   char received_data = '\0';
   if (uart__get(UART__3, &received_data, portMAX_DELAY)) {
     strncat(bluetooth_command_received, &received_data, 1);
     if (received_data == '\n') {
       bluetooth__process_receive_data(bluetooth_command_received);
       strcpy(bluetooth_command_received, "\0");
    }
   }
  }
 }

The following code snippet was used to process the received data. It simply compares the strings and, if the match is found the direction is set accordingly.

void bluetooth__process_receive_data(char string[]) {
 if (strcmp(string, "CENTERED\r\n") == 0){
   set_joystick_direction(CENTERED);
   printf("CENTERED\n");
 } else if (strcmp(string, "RIGHT\r\n") == 0){
   set_joystick_direction(RIGHT);
   printf("RIGHT\n");
 } else if (strcmp(string, "JOYSTICK_ON\r\n") == 0) {
   set_joystick_button_pressed(true);
   printf("JOYSTICK_BUTTON\n");
 }
}



Game pad Controller

Gamepad Controller basically consists of only three main components. Firstly the joystick, which is used to get the UP and FORWARD direction, and also the press button. Second is the Bluetooth module which is used to transmit the data via UART to the other board. And lastly, the vibration sensor to produce the vibration. The vibration sensor is used to get the real game feel.


Game Pad Controller

Joystick

The joystick was interfaced on the Game-pad controller. We used a joystick to get a UP and FORWARD direction. The joystick was configured using ADC pins of the SJ2 board. The Joystick provides an analog output, therefore they were connected to ADC pins to get the digital values. The values of the X-axis and Y-axis varied from 0 to 4095. The center was 2048 for both X-axis and Y-axis. The UP and FORWARD direction was calculated using these ADC values. The joystick also had a digital switch. This digit switch was used as a press button in our game. These three contents (i.e UP, FORWARD, Button_press) were transmitted to the led board using Bluetooth.


Joystick Module


Hardware Design

The hardware design was pretty simple. The two analog output pins i.e X-axis and Y-axis were connected to ADC pins of the SJ2 board. The ADC pins used were P1.30 and P1.31 to get the UP direction and the FORWARD direction. The digital switch was connected to one of the gpio pins on the SJ2 board. This gpio pin was read to detect if the switch was pressed.


Joystick Schematics


Software Design

This code snippet below demonstrates how we calculated the direction using the joystick. The joystick provides the analog values, so we used the ADC pins of the SJ2 board to get the digital values. The values range from 0 to 4095. According to these values threshold for UP and FORWARD/RIGHT were set.

static const int16_t UP_threshold = 500;
static const int16_t RIGHT_threshold = 3500;
joystick_direction_t joystick_controls__get_joystick_direction(void) {
 joystick_direction_t joysticks_direction = CENTERED;
 int joystick_pos_x = adc__get_channel_reading_with_burst_mode(X_axis);
 int joystick_pos_y = adc__get_channel_reading_with_burst_mode(Y_axis);
 if (joystick_pos_y < UP_threshold) {
   joysticks_direction = UP;
   printf("UP\n");
 }
 if (joystick_pos_x > RIGHT_threshold) {
   joysticks_direction = RIGHT;
   printf("RIGHT\n");
 }
 vTaskDelay(500);
 return joysticks_direction;
}

Vibration Module

A vibration module was used to produce the vibration on the game-pad controller to get the real feel of the game. The vibration module was triggered on the Mario jump state and also when Mario died.


Vibration module

Hardware Design

Vibration consists of just 3 pins. VCC for power, Signal pin to trigger the pin, and GND. The signal pin of the vibration module was connected to one of the gpio pin (P0.29) of the SJ2 board.


Vibration module schematics

Software Design

A GPIO pin was used to signal the SIG pin of the vibration module.

gpio_s vibration_module_pin = {1, 29};

gpio__set(vibration_module_pin);
 delay__ms(500);
 gpio__reset(vibration_module_pin);

Testing & Technical Challenges

MP3 Decoder

  • The datasheet lacks some information and clarity on module initialization and working. Initially, non of the commands appeared to work or have any effect. The issue was resolved after sending the command to select a device, which was not explicitly stated in the datasheet. Once this command is first sent, the MP3 decoder now begins accepting commands.
  • The TF card folder structure for songs was unclear in the first go.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Project Source Code

XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX

Acknowledgement

We'd want to express our gratitude to our professor Preet and all of the ISAs for putting together such a fantastic class and for setting such high standards. This instilled in us the desire to go above and beyond.

References Used


LED Matrix


Image Designing


MP3 Decoder


HC-05 Bluetooth Modules


PCB Designing