|
|
| Line 97: |
Line 97: |
| | * Electronic Speed Controller (included w/hull) | | * Electronic Speed Controller (included w/hull) |
| | | | |
| − | == Design & Implementation ==
| + | = Design & Implementation = |
| | The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation. | | The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation. |
| | | | |
| − | === Hardware Design ===
| + | == Hardware Design == |
| | Considerations for our hardware include power consumption and usefulness in a water scenario. | | Considerations for our hardware include power consumption and usefulness in a water scenario. |
| | The root of this project where sensor input is analyzed and output signals are distributed | | The root of this project where sensor input is analyzed and output signals are distributed |
| Line 108: |
Line 108: |
| | | | |
| | | | |
| − | [[File:Project_Hardware_Overview_ANSOTAS.jpg|300px|thumb|center]] | + | [[File:Project_Hardware_Overview_ANSOTAS.jpg|450px|thumb|center]] |
| | | | |
| | = Hardware Interface = | | = Hardware Interface = |
Revision as of 02:29, 21 December 2016
Grading Criteria
- How well is Software & Hardware Design described?
- How well can this report be used to reproduce this project?
- Code Quality
- Overall Report Quality:
- Software Block Diagrams
- Hardware Block Diagrams
- Schematic Quality
- Quality of technical challenges and solutions adopted.
Autonomous Nautical Systems for Ocean Transit and Survey (ANSOTAS)
Abstract
Constructing an autonomous navigation system responsive to GPS and Tilt Compass feedback to form and track trajectories to a given location. Low power, and observant system.
Objectives & Introduction
Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.
Team Members & Responsibilities
GPS control
Servo control
Motor Control
Schedule
Table 1. Schedule
| Week#
|
Date
|
Tasks
|
Actual
|
| 1
|
10/8
|
Decide on boat hull based on the amount of devices
we planned to us.
Purchased motor, servo, and battery accordingly
|
Completed
Brushed DC motor powered by Electronic
Speed controller was purchased.
|
| 2
|
11/4
|
Intercept the pwm signals issued by a remote
control for steering and speed throttling. Decode
these signals over time to identify which values produce
what kind of effect to the driving system.
|
Completed
Using a logic analyzer did not work the way we planned
An oscilloscope was used but only to prove that this
was not necessary since the motor and servo reacts to
PWM as any other motor or servo.
|
| 3
|
11/25
|
Make separate compass, gps, and pwm tasks
|
Completed
These tasks are a simple tasks demoing the functionality
|
| 4
|
12/02
|
Link separate task outputs together using navigation task.
|
Completed
Debug the steering and motor control commands issued
by the state of the navigation task state machine.
|
| 5
|
12/16
|
Revise gps task to give only needed information and use
all task outputs in the navigation task
|
Completed
Buggy and needs to check for invalid information using checksum
|
| 6
|
12/20
|
Update the wiki page
|
Completed
Clean up exceptions in the land demo program
|
Parts List & Cost
- SJ One Board | $80.00
- Tilt Corrected Compass | $30.00
- GPS | $50.00
- 7.2V 2600mAH Battery (included w/hull)
- 5V 5200mAH Battery | $13.00
- Hull | $155.00
- DC Motor (included w/hull)
- Servo (included w/hull)
- Electronic Speed Controller (included w/hull)
Design & Implementation
The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.
Hardware Design
Considerations for our hardware include power consumption and usefulness in a water scenario.
The root of this project where sensor input is analyzed and output signals are distributed
is the SJ One board. Using the FreeRTOS OS an autonomous system can adjust its velocity
and direction by controlling the motor and servo. GPS and Tilt compass provides the feedback
needed to make adjustments.
Hardware Interface
I2C
I2C was used to communicate to and from the SJ One board to the tilt adjusted compass. This protocol allows numerous sensors to be connect to a single wire to all devices for transmitting and receiving address and data information. This is possible because of synchronization of a clock signal and a pull-up resistor used in setting up the data/address bus. The disadvantage with this choice is speed since it can only transfer a max of 100KHz.
For our design we use our SJ One board as the master and the compass as the slave device. It is only enabled if it receives it's address from the master. Through out the operation of protocol a slave and master are under constant bidirectional communication. Using a byte or more to communicate what is desired in the form of an slave address, byte address and a quantity for receiving or transferring data. This continuous process follows a state machines for both the slave and master devices.
SPI
UART
PWM
Software Design
Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.
Implementation
This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.
Testing & Technical Challenges
Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again?
Make a smooth transition to testing section and described what it took to test your project.
Include sub-sections that list out a problem and solution, such as:
My Issue #1
Discuss the issue and resolution.
Conclusion
Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?
Project Video
Upload a video of your project and post the link here.
Project Source Code
References
Acknowledgement
Any acknowledgement that you may wish to provide can be included here.
References Used
GPS module DataSheet
NMEA Decoding
GPS Recommended Minimum Specifics Parsing
SJ One board MCU Datasheet
SJ One board Introduction
Appendix
You can list the references you used.
