Difference between revisions of "F15: Undergrads++"

Revision as of 10:05, 17 December 2015

Undergrads++

Abstract

The project is an autonomous car that shall avoid obstacles. The car will consist of five SJ One controllers connected and communicating via one operational CAN bus. Each controller shall be handled by teams of two people per component and integrated to 1 working autonomous car. The Master Controller team shall be responsible for collecting data from the other controllers and guiding the car using high-level logic. The Motor I/O Controller team shall be responsible for the operation of the motors and operation of the LCD display, which will display debugging or current status messages. The Sensor Controller team shall be responsible for collecting data from the sonar sensor and sending the appropriate data. The Geographical Controller team shall be responsible for calculating the orientation of the car. The Bluetooth/Bridge Controller team shall be responsible for the interface to the end user and sending the way-points. All of these five devices shall operate simultaneously and reach the requested destination.

Objectives & Introduction

• The user shall be able to set a longitude/latitude using an Android app
• The user shall be able to send a Start command to start the navigation routine
• The car shall avoid obstacles and navigate appropriately around them
• The car shall contain sensors in the front and back to go forward and backward without intervention
• The car shall reach the destination before the battery dies
• The car shall contain a GPS and compass to calculate the heading, longitude, and latitude
• The car shall contain a Bluetooth device to receive information from the Android App
• The car shall contain appropriate sensors to internally calculate the speed of the car
• The car shall be able to adjust it's speed appropriately when commanded by the Master controller
• The car shall display appropriate information on the LCD display

System Communication Overview

Team Members & Responsibilities

Master Controller

• Marvin Flores
• Hassan Naveed

Sensor Controller & Finances

• Arlen Eskandari
• Onyema Ude

GPS Controller

• Calvin Lai
• Jonathon Hongpananon

Motor/LCD Controller

• Hector Prado-Guerrero
• Jashan Singh

Bridge/Android Controller

• Phil Tran
• Shangming Wang

Parts List & Cost

This section goes over the parts that we ordered and the cost of each item.

Design & Implementation

The section goes over our top-level designs of our project.

CAN Message ID Table

DBC File Implementation

Throughout the development and life-cycle of our project we used a DBC file and a python parser to generate C-code for the five controllers. The DBC file contained CAN messages organized in a particular format, which the python parser generated appropriate code for each CAN node. The C-code generated contained inline functions to convert messages to and from raw CAN messages using marshal and unmarshal operations. This provided a centralized CAN message base for all of the teams to use so that there was consistency throughout the project.

• The DBC file :

 VERSION ""
  
 
 NS_ : 
 	NS_DESC_
 	CM_
 	BA_DEF_
 	BA_
 	VAL_
 	CAT_DEF_
 	CAT_
 	FILTER
 	BA_DEF_DEF_
 	EV_DATA_
 	ENVVAR_DATA_
 	SGTYPE_
 	SGTYPE_VAL_
 	BA_DEF_SGTYPE_
 	BA_SGTYPE_
 	SIG_TYPE_REF_
 	VAL_TABLE_
 	SIG_GROUP_
 	SIG_VALTYPE_
 	SIGTYPE_VALTYPE_
 	BO_TX_BU_
 	BA_DEF_REL_
 	BA_REL_
 	BA_DEF_DEF_REL_
 	BU_SG_REL_
 	BU_EV_REL_
 	BU_BO_REL_
 	SG_MUL_VAL_
 
 BS_:
 
 BU_: NOONE SENSOR MASTER MOTOR GPS ANDROID
 
 BO_ 100 HEARTBEAT: 1 MASTER
  SG_ MASTER_HEARTBEAT_cmd : 0|8@1+ (1,0) [0|0] "" SENSOR,MOTOR
 
 BO_ 600 INFO_SONARS: 4 SENSOR
  SG_ SENSOR_INFO_SONARS_left : 0|8@1+ (1,0) [0|255] "inch" MASTER
  SG_ SENSOR_INFO_SONARS_middle : 8|8@1+ (1,0) [0|255] "inch" MASTER
  SG_ SENSOR_INFO_SONARS_right : 16|8@1+ (1,0) [0|255] "inch" MASTER
  SG_ SENSOR_INFO_SONARS_rear : 24|8@1+ (1,0) [0|255] "inch" MASTER
 
 BO_ 604 MOTOR_CMD: 2 MASTER
  SG_ MASTER_MOTOR_CMD_steer : 0|8@1+ (1,0) [0|20] "" MOTOR
  SG_ MASTER_MOTOR_CMD_drive : 8|8@1+ (1,0) [0|20] "" MOTOR
 
 BO_ 700 STOP_GO_CMD: 1 ANDROID
  SG_ ANDROID_STOP_CMD_signal : 0|8@1+ (1,0) [0|0] "" MASTER,GPS
 
 BO_ 708 INFO_CHECKPOINTS: 1 ANDROID
  SG_ ANDROID_INFO_CHECKPOINTS_count : 0|8@1+ (1,0) [0|255] "" MASTER,GPS 
 
 BO_ 712 INFO_COORDINATES: 8 ANDROID
  SG_ GPS_INFO_COORDINATES_lat : 0|32@1+ (0.00001,0) [0|0] "" MASTER,GPS
  SG_ GPS_INFO_COORDINATES_long : 32|32@1+ (0.00001,0) [0|0] "" MASTER,GPS
 
 BO_ 716 INFO_HEADING: 4 GPS
  SG_ GPS_INFO_HEADING_current : 0|16@1- (1,0) [0|0] "" MASTER
  SG_ GPS_INFO_HEADING_dst : 16|16@1- (1,0) [0|0] "" MASTER
 
 BO_ 720 DESTINATION_REACHED: 1 GPS
  SG_ GPS_DESTINATION_REACHED_signal : 0|8@1+ (1,0) [0|0] "" MASTER,ANDROID
 
 CM_ BU_ NOONE "No node, used to indicate if it's a debug message going to no one";
 CM_ BU_ MASTER "The driver controller driving the car";
CM_ BU_ SENSOR "The sensor controller of the car";
 CM_ BU_ MOTOR "The motor controller of the car";
 CM_ BU_ ANDROID "The android controller of the car";
 CM_ BO_ 100 "Sync message used to synchronize the controllers";
 
 BA_DEF_  "BusType" STRING ;
 BA_DEF_ SG_ "FieldType" STRING ;
 BA_DEF_ BO_ "GenMsgCycleTime" INT 0 0;
 
 BA_DEF_DEF_ "BusType" "CAN";
 BA_DEF_DEF_ "FieldType" ""; 
 
 BA_ "GenMsgCycleTime" BO_ 100 1000;
 BA_ "GenMsgCycleTime" BO_ 200 100;
 BA_ "GenMsgCycleTime" BO_ 300 100;
 BA_ "FieldType" SG_ 100 MASTER_HEARTBEAT_cmd "MASTER_HEARTBEAT_cmd" 
 BA_ "FieldType" SG_ 604 MASTER_MOTOR_CMD_drive "MASTER_MOTOR_CMD_drive"
 BA_ "FieldType" SG_ 604 MASTER_MOTOR_CMD_steer "MASTER_MOTOR_CMD_steer"
 
 VAL_ 100 MASTER_HEARTBEAT_cmd 0 "MASTER_HEARTBEAT_cmd_NOOP" 1 "MASTER_HEARTBEAT_cmd_SYNC" 2 "MASTER_HEARTBEAT_cmd_REBOOT" ;
 VAL_ 604 MASTER_MOTOR_CMD_drive 4 "MASTER_MOTOR_CMD_drive_FAST" 3 "MASTER_MOTOR_CMD_drive_MEDIUM" 2 "MASTER_MOTOR_CMD_drive_SLOW" 1 "MASTER_MOTOR_CMD_drive_REVERSE" 0 "MASTER_MOTOR_CMD_drive_STOP" ;
 VAL_ 604 MASTER_MOTOR_CMD_steer 4 "MASTER_MOTOR_CMD_steer_HARD_RIGHT" 3 "MASTER_MOTOR_CMD_steer_SOFT_RIGHT" 2 "MASTER_MOTOR_CMD_steer_STRAIGHT" 1 "MASTER_MOTOR_CMD_steer_SOFT_LEFT" 0 "MASTER_MOTOR_CMD_steer_HARD_LEFT"   ;
 

Git Submodule Add-on

To increase productivity and be more organized through the life-cycle of this project our team implemented and used a git submodule. A git submodule is a separate Git repository, which is a subdirectory of our entire main Git repository. What this does is lets us clone another repository within our project and keep commit history of this submodule separate from the separated projects. The Git submodule allowed a central repository to be used for common code such as the DBC file, python parser, and other source/header files we shared. Every team had a separate branch they were working off of the master branch so there was no way for us to share common code. The submodule made code portable to all teams instead of manually making chances when necessary. For example, if 1 team made a change to a file, then the other 4 teams already have the recent change without having to manually update. The update is automatic to everyone who has the Git submodule set up.

• To set up a git submodule you can perform the following instructions:
  • Create your separate repository on GitLab.com or GitHub.com, whichever Git repository you prefer to use.
  • Execute : git submodule add ssh_url relative_path_to_new_dir
  • Execute : git status
  • Notice a new change to be commited. There should be a .gitmodule created. This contains details supplied about the new submodule.
  • Execute : git submodule init
  • Execute : git submodule update
• To use the git submodule you just 'cd' into the directory where the git submodule repo is located, and treat it as an independent Git project. There is a master branch you can checkout and pull from to pull-in the most recent changes. Make commits and push like you would to any other Git project. When there are changes made to this Git submodule then there will be new changes shown in the top project directory. You will want to add this change to your next commit so that your top project points to the correct Git submodule commit number.

Master Controller

Master Controller

• Marvin Flores
• Hassan Naveed

Master Controller Team Schedule

Hardware Design

For the master controller, hardware part essentially covers setting up the CAN bus. The master controller communicates with all other controllers on board i.e the motor, android, GPS, compass and sensors. The bus was set up using five SN65HVD233-HT 3.3-V CAN transceiver chips to send and receive CAN messages from the master controller.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

The RD1 (pin 0.0) and TD1 (pin 0.1) on the SJ ONE board are connected to the CAN RECEIVE data output and CAN TRANSMIT data input pins on the CAN transceiver. A 120 ohm resistor is attached as a termination resistor between CANH and CANL pins of the two transceivers. This ensures that a transmitting node does not get its own reflection. For the software part, we configured the CAN bus using the FULL CAN mode. The main advantage of using the FULL CAN is that the processor does not have to parse the incoming message and messages go inside designated mail boxes. To initialize the CAN bus in FULL CAN mode, we set its baud rate to be 100kbps, the receive and send queue size to be 50 and pass an array of accepted message IDs and its size as parameters to the following function which initializes the CAN BUS.

bool iCAN_init_FULLCAN(uint32_t * std_list_arr, size_t arraySize); The function returns true if the bus is initialized successfully and all the message IDs are added to the acceptance filter. Now to

These messages can then be read using a pointer to that mail box like:

iCAN_rx(&fc_msg, msg_id_to_check);

Software Design

Motor Control Logic

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

The software design is based on layered architecture. There are a total of three layers and they are listed below:

• Communication layer - responsible for sending and receiving can messages
• Data layer - responsible for extracting or encoding the data from CAN messages
• Control layer - responsible for making decisions based on data processing and controlling the overall behavior of the car.

Motor I/O Controller

Motor/LCD Controller

• Hector Prado-Guerrero
• Jashan Singh

Motor control/LCD Team Schedule

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

The Android program was written with the Android SDK. The program uses one Activity and three fragments under that Activity (as seen in the Visio diagram). The Activity is the base of the program, and it manages the three fragments in it using a FragmentTransaction and FragmentManager class. There is another layout in the Activity's layout that is specifically made as a fragment container. The Activity features three buttons at the bottom of the screen. Each button with show a fragment. All fragments are constantly running, and the Activity simply hides fragments from the user when the user clicks on a button in the bottom menu. Fragments communicate with each other by using the Activity as a middle man. Information from Fragment A can pass its information to Fragment B by first going through Activity.

Google Maps was inserted into the Maps Fragment. An API key was needed in order for Google Maps to work on the phone. An open source API was used to get the directions and and coordinates of the start and end position. A LatLng list array was inserted to the API to get the list of coordinates. After choosing a point, the "SET" button should be pressed, and the array will be transmitted through bluetooth. The Maps Fragment features buttons that allow operation of the vehicle. These buttons will transmit data to the SJOne board through Bluetooth.

The Bluetooth API was used to send data to and from the Android and SJOne board. When transmitting data from Android to SJOne, a terminal command is used on the SJOne board side to receive data. This is done by using the UART2 ports of the board, and connecting it with a Bluetooth transceiver.

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Sensor Controller

Sensor Controller & Finances

• Arlen Eskandari
• Onyema Ude

Sensor Controller Team Schedule

Hardware Design

4 LV-MaxSonar sensors are used for the project, they are used for obstacle detection and avoidance. These sensors are able to detect obstacles 0 – 254 inches, though objects 6 inches or closer are simply registered as 6 inches. Sensors are powered with 5Volts (3.3Volts option is also available). Each reading takes 50ms, and each sensor is enabled at a time using the RX pin on the sensor to avoid crosstalk. Three sensors are placed in front of the car (Left , Middle, Right) and one at the back. The image below shows the wired connections between sensors and SJOne board.

Sensor Hardware Design

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

In this project the PWM option of the sonar sensor is used to measure the distance. To have the sensor to range, 250ms after the power up the sensors are ready to take their first measurement, the very first measurement take 98ms (49ms for initial calibration) and the consecutive measurements take 49ms each.

The software start measuring from in order of Left, middle, right, and rear sensors. To measure the PW pin of the sensor (which is connected to a dedicated GPIO pin separately for each sensor) is held high for 50ms (49ms is the minimum), at the moment the software saves the system clock uptime in a variable "trig_time". As soon as sensor is enabled, it sends out an ultrasonic burst, after the burst is bounced back from an obstacle and at the moment when the sensor receives the bounced back burst the "PW" pin of the sensor which is connected to an "interrupt enabled" (falling edge enabled) GPIO pin is pulled low. The moment the Interrupt enabled GPIO pin goes low, the interrupt service routine goes to "calculate_dist" function to calculate the distance by first subtracting the current system uptime from trig_time which was saved before; the dividing it by 174 (given by datasheet) to measure the distance in inches.

After the left sensor finished its measurement, the RX pin on the left sensor is pulled low to disable the sensor, then the RX pin of the middle sensor is pulled high to enable the sensor (at this moment all other sensors are disabled except the middle one to eliminate crosstalk. Then after enabling the middle sensor all the ranging procedure is identical to the one explained above. For the right, and rear sensors the same procedure is repeated all over.

void Range_left(void) {

   Left_en.setHigh(); // enable Ranging   (enable left sonar)
   delay_us(21); //hold high  >20uS to enable ranging
   Left_trig_time = sys_get_uptime_us(); //get timer at the moment ranging starts
   Left_en.setLow(); // disable ranging of left sonar

} void Range(){

   Range_left();
   delay_ms(50);
   Range_middle();
   delay_ms(50);
   Range_right();
   delay_ms(50);
   Range_rear();
   delay_ms(50);
   CAN_send();
   test();

}

Bluetooth/Bridge Controller

Bridge/Android Controller

• Phil Tran
• Shangming Wang

Android/Bluetooth Team Schedule

Hardware Design

The Bridge communication hardware design is very simple. A BTBEE Pro Bluetooth XBee socket chip is connected to the SJOne board. UART2 port on the SJOne board is used. UART2 Rx and Tx from the pins on the board are connected to the CAN Bus, which is then connected onto the CAN wires.

Android Hardware Design

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

The Android program was written with the Android SDK. The program uses one Activity and three fragments under that Activity (as seen in the Visio diagram). The Activity is the base of the program, and it manages the three fragments in it using a FragmentTransaction and FragmentManager class. There is another layout in the Activity's layout that is specifically made as a fragment container. The Activity features three buttons at the bottom of the screen. Each button with show a fragment. All fragments are constantly running, and the Activity simply hides fragments from the user when the user clicks on a button in the bottom menu. Fragments communicate with each other by using the Activity as a middle man. Information from Fragment A can pass its information to Fragment B by first going through Activity.

Fragment Layout under Activity

Fragment Layout under Activity

Google Maps was inserted into the Maps Fragment. An API key was needed in order for Google Maps to work on the phone. An open source API was used to get the directions and and coordinates of the start and end position. A LatLng list array was inserted to the API to get the list of coordinates. After choosing a point, the "SET" button should be pressed, and the array will be transmitted through bluetooth. The Maps Fragment features buttons that allow operation of the vehicle. These buttons will transmit data to the SJOne board through Bluetooth.

The Bluetooth API was used to send data to and from the Android and SJOne board. When transmitting data from Android to SJOne, a terminal command is used on the SJOne board side to receive data. This is done by using the UART2 ports of the board, and connecting it with a Bluetooth transceiver.

The Bluetooth communication is sent using the write function on Android. Each write function takes a command that the terminal command one the SJOne board will receive. At every command, an action happens. Every command takes a format:

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Geographical Controller

The Geographical Controller is responsible for providing the location of the car and heading direction to the master controller. It receives the way-points from the Bridge Controller and calculates the distance to the final destination. The Master Controller is still responsible for controlling the logic of forward, backward, left, and right to reach the final destination.

GPS Controller

• Calvin Lai
• Jonathon Hongpananon

GPS Controller Team Schedule

Hardware Design

The figure below illustrates the high-level design for the Geographical Controller. The Geographical controller uses an Adafruit GPS Breakout and an Adafruit 10 Degrees Of Freedom (DOF) IMU Breakout. The Adafruit GPS breakout is a GPS module with a 10Hz update rate with a low current draw, which makes this an excellent device for low power consumption. The Adafruit 10-DOF IMU Breakout contains an accelerometer, gyroscope, magnetometer, barometer, and temperature sensor; however, only the magnetometer was used to calculate the heading direction.

Geographical Hardware Design

Hardware Interface

Software Design

GPS Data Format

The following table below shows the type of information that is retrieved from the Adafruit GPS chip. When interfaced with the GPS via UART, the string that is received is in the format

$GPGGA,hhmmss.ss,llll.ll,a,yyyyy.yy,a,x,xx,x.x,x.x,M,x.x,M,x.x,xxxx*hh.

The Geographical Controller is responsible for parsing this information and handling the data appropriately.

Tasks

Algorithms Used

 correctHeading = atan2(dy, dx) * 180 / pi; (where dy and dx are the delta of latitude and longitude)

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

Problems Encountered

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

• Sourceforge Source Code Link
• GitLab Source Code Link
• Git Submodule Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.