Difference between revisions of "S14: Quadcopter"

Revision as of 21:01, 23 April 2014

Grading Criteria

Quadcopter

Abstract

A Quadcopter (Quad-rotor helicopter) is a multi-rotor aerial vehicle that is lifted and propelled by four rotors. The thrust generated by the propellers lifts the Quadcopter while the flight controller system govern the rotor speed for attitude control. A wireless remote control is used to interact with the flight controller system for changing the flight path. Our objective is to assemble the Quadcopter, then design and build a flight controller system that stabilizes the flight and accept commands from a hobbyist remote control during its flight.

Objectives

The scope of our project can be divided into three parts:

• Design and build interfaces to all the on-board electronic sensor such as IMU, barometer and distance sensors
• Design and build interfaces to telemetry and radio modules to communicate with remote control and the computer
• Process the various sensor inputs and control the brushless motors on board using an electronic speed control system to stabilize the aircraft

Team Members & Responsibilities

1. Sree Harsha
   • PWM Design, Remote Control Input, Quadcopter assembly
2. Balaji
   • Sensor Data Processing, Quadcopter Assembly
3. Divya Kamath
   • Flight Controller Design, Code Integration

Introduction

Quadcopter is one of the successful aerial vehicles which support vertical take-off and landing.It has 4 rotors - 2 run clockwise(CW) and 2 counter-clockwise(CCW). This is to cancel out the torque generated by a set of rotors running in any one direction.

There are two types of orientation for a quadcopter : + configuration and X configuration. Our design is an X configuration as it allows unblocked front view for mounting a camera. The quadcopter motion in the 3 axis is known as Pitch, Roll and Yaw.

Pitch is the ascending or descending motion. Roll is tilting towards the left or right. Yaw is rotating left or right.

Quadcopter Modes

Most commercially available quadcopters work in one of two possible modes:

1. Aerobatic Mode: This mode allows you to perform spins and flips on the quadcopter. The accelerometer is not necessary in this case.
2. Attitute/Stable Mode: This is the preferred mode for beginners and this is the mode our quadcopter will run in. In this mode, data from accelerometer and gyro sensor is combined to calculate the quadcopter angle. Once the remote control stick is moved to non-idle location, the quadcopter angle is changed accordingly and held at the angle. Unlike the aerobatic mode, no spins or flips will be performed.

Remote Control Channels

We are currently using a 6 channel remote control to maneuver the quadcopter. The 6 channels are as below:

1. Roll/Aileron - Controls the aircraft's right/left movement
2. Pitch/Elevation - Moves the copter front/back
3. Throttle - Increases the thrust output of the motors
4. Yaw/Rudder - Causes movement about the vertical axis. This changes the direction in which the aircraft is pointing.
5. Gear
6. AUX1

Arming/Disarming the Quadcopter

Schedule

Parts List & Cost

Backup Parts & cost

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Pin Connections

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Current Design UART for reading sensor data PWM for motor control UART for telemetry

Software Design

MPU-9150

The MPU-9150 consists of a 3-axis accelerometer, 3axis Gyroscope and a 3 axis magnetometer. its a one chip IMU solution with onboard Motion processor for sensor fusion.Though it inherently supports on board Sensor Fusion, the IP is undisclosed. Therefore we used the library for arduino by Pansenti. (https://github.com/Pansenti) The 6 axis sensor fusion (accel+gyro) is done on the MPU and sent to an arduino where the magnetometer data is used for YAW correction. The arduino transmits the orientation data over UART which is recieved by the SJONE for further processing.

For testing, we coded a GUI in python. The code parses the serial data from the arduino and displays the orientation of the IMU in real-time using Vpython.(video and code to be linked).

PID Controller

For our flight controller algorithm, we are using a PID controller. PID (proportional, integral, derivative) controller is a feedback control system which attempts to minimize the error in the output using three constant values: P, I and D i.e. the proportional, integral and derivative values.

Converting Remote Control Data to Motor Speed

The following steps are involved in converting raw RC (remote control) data to motor speed

1. Get the RC data. Usually a PWM signal
2. Scale up/down this value using a pre-decided curve. (Linear/Exponential)
3. Convert this value into angles.
4. Apply PID on Roll/Pitch/Yaw RC command (Using the angles calculated by IMU (Inertial Measurement Unit) as the PID input and angles calculated from the previous step as the desired setpoint)
5. Use these angles to adjust motor speeds and direction (Add/Subract to Throttle Command)

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Mechanical Design

Testing & Technical Challenges

Getting a quadcopter is fly smoothly isn't a smooth process at all. But failures do have teach us a lot. Listed below are some of the issues we faced during the course of this project.

Quadcopter Assembly

1. Unexpected Throttle: Throttle seems to shoot to maximum without command. Solution - Order new remote control (:O)
2. Bricked ESC: Tried flashing SimonK Firmware into ESC for faster update rate. ESC didnt respond! Solution - Buy a whole new set ESCs (!)
3. Propeller Issue: Didnt check propeller specs before ordering. Had to return.
4. Specifications were not clear for the products ordered online: Motors were too big for the frame. Different countries follow different metrics. Need to be careful while assembling parts ordered from different websites.
5. Magnetic Interference on Compass:Motors create really intense magnetic fields which interferes with the magnetometers magnetic field. As a result magnetometer readings are affected. Magnetometer needs to be kept at an elevation to avoid this.

Quadcopter Software

1. UART FIFO: If messages longer than 16 bytes is transmitted over UART, then all characters exceeding 16 bytes are lost. This issue is yet to be resolved. Looking into it.
   1. (4/23)Resolved this by using Interrupts and queues. The polling method created a time delay causing some data to be lost.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

Send me your zipped source code and I will upload this to SourceForge and link it for you.

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

1. https://github.com/Pansenti
2. https://code.google.com/p/sf9domahrs/
3. http://www.rcgroups.com/forums/showthread.php?t=1284741
4. http://blog.oscarliang.net/quadcopter-pid-explained-tuning/
5. http://aeroquad.com/showthread.php?1167-Stable-Mode-Explained
6. http://www.ece.ucdavis.edu/~spencer/195/datasheets/PID-Without-a-PhD.pdf
7. http://support.motioneng.com/downloads-notes/tuning/pid_overshoot.htm
8. http://www.instructables.com/id/RC-Quadrotor-Helicopter/?ALLSTEPS
9. http://www.modelflight.com.au/blog/how-to-fly-remote-control-quadcopter/

Appendix

You can list the references you used.