Difference between revisions of "S18: Team Nemesis(SJSU Cam)"

Revision as of 22:28, 23 May 2018

Grading Criteria

SJSU Cam

Abstract

Our project is a digital camera implemented using the SJONE board. An image is captured using a camera and is then displayed on an LCD screen. An SD card is also used to store the output of the camera as the captured image. For navigating through various options on the LCD screen, a menu is created.

The camera is mounted on a 3D printed box which contains an LCD screen behind to display the image being captured by the camera.

Objectives & Introduction

The objective for this project was to learn how timing and buffer play an important role in capturing the pixels from the camera and displaying them on the LCD screen. The following objectives were set for the project:
1. Write a driver for camera (mention what kind of camera ), which has a better rate of capturing the image with the SJONE board and integrate it.
2. Store the output of the camera to SD card.
2. Write the driver for LCD (mention the name) and integrate it by choosing the right resolution.
3. Have a menu implemented for the options available on the digital camera.

Team Members & Responsibilities

• Chhavi Mehta
  • Camera Module Driver
• Deeksha Prakash Kankalale
  • PCB Design, Camera driver interfacing.
• Parth Gujar
  • LCD Module Driver, 3D design.
• Sagar Kalathia
  • LCD Module interfacing, implementing graphics library
• Saurabh Badenkal
  • LCD Driver, Integration of camera and LCD on the PCB and data pipelining.

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Parts List & Cost

Design & Implementation

This design section outlines the hardware and software design of the project.

Hardware Design

The two main hardware components used in the project are discussed in detail below.

LCD Screen:

Figure : 5 inch LCD screen This is a 5.0" TFT screen with 800x480 pixels. These screens are commonly seen in consumer electronics, such as miniature TV's, GPS's, handheld games car displays, etc. A 40-pin connector has 8 red, 8 green, and 8 blue parallel pins, for 24-bit color capability. The display is supposed to be constantly refreshed, at 60Hz, with a pixel clock. The backlight requires a constant-current mode boost converter that can go as high as 24V. Hence along with the display we use an RA8875 driver board.

LCD Driver :

Figure : RA8875 Driver Board

The RA8875 is a powerful TFT driver chip, it has 768KB of RAM, so it can buffer the display (and depending on the screen size also have double overlaying).The RA8875 can also handle standard 4-wire over the SPI interface.

Camera:

Figure : OV2640 camera

The OV2640 Camera Module is a small image sensor, works at low operating voltages.It provides all functions of a single chip of VGA camera and image processor. Through Serial Camera bus control, the sensor can output the whole frame, sampling at various resolution 8 bits of data. The product VGA image can reach up to a maximum of 30 frames per second. We can control the image quality, data format and transmission mode. All the process of image processing functions can through the SCCB programming interface, including gamma curve, white balance, saturation, and chroma .

Camera Module Block Diagram :

System block diagram:

Hardware Interface

The SPI interface is done to both the camera and the driver board of the LCD display. The PCB design was done on Dip Trace, which is a CAD software for creating schematic diagrams and printed circuit boards.

Schematic:

PCB Design:

Software Design

Software Design mainly consist of two part

1) Design for LCD : LCD would continuously display menu on its right with different option. Menu driver is programmed dynamically using pointers & Function Pointer.

Various API & functions as follows:

• Add_Menu API, whenever gets called would add one more node to linked list.

• Add_Submenu API would create Node inside its parent Node.

• "Navigate" API enables user to navigate through Menus. This API navigates pointer to different nodes and calling respective functions such as capture image or going inside sub_menu.

With this dynamic functionality we can create menus as required inside which we can call respective function to be performed according to submenu.

2) Design for SJOne & CAM : Controller has to Configure camera, receive data from camera and send this to LCD as soon as it gets the data.

Function includes :

• To Configure Camera Includes

• To receive Data from Camera at 8 MHz through SPI. After receiving One Frame, it is sent to LCD via SPI. In both the case, Controller is Master and other device is slave.

• To Store Image in SD card, whole frame is sent to SD card through SPI, and new text file with unique name is created and pixel values in that text file would be ascii values in matrix.

Software Flow of Project:

The general flow of our project can be explained by the flowchart shown below:

Implementation

The camera is interfaced to the board where Image Sensor Configuration is done through I2C Protocol and Sending pixel data through SPI communication protocol. The raw pixels are read from the camera to the SJONE board. There are five buttons on the camera. One of them used to capture an image and store it on the SD card. The LCD screen is interfaced through SPI communication protocol. The raw pixels received from the camera are displayed on to the LCD screen.

MENU for the LCD

A menu was designed for the LCD screen using an LCD_MENU class. This class included functions like adding sub-menu, displaying them or loading previous ones. It helped in dynamically adding options for the innumerous camera settings like changing image resolution and format.The private members of this class are as shown:

   private:
   type myType;                         //to know if current object is itemType or menuType
   str myName;                          //name of this object
   LCD_MENU *ParentMenu;                //parent menu of current menu object
   LCD_MENU *CurrentMenu;               //reference to global CurrentMenuG
   VECTOR<Element> all_elements;        //to store all elements by Element .name .id and .type
   VECTOR<str> all_elements_name;       //to store all elements by name to use by Find function
   int highlighted;                     //to track currently highlighted sub-element

Similar to the this class, a file_explorer class was implemented for navigating through the SD card files.

Testing & Technical Challenges

Problem 1: Making any camera work on SJOne can be little tricky. We found SJOne to be not so compatible with camera modules and have timing issue which leads to displaced images or sometimes no image at all.

Solution: After trying a number of cameras like OV7670 without fifo and VC0706 serial camera, we were able to solve the problem by using OV2640 camera with fifo which made capturing the image easier because the buffer saved the values rendering the timing issues.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

• Sourceforge Source Code Link

References

Acknowledgement

We would like to thank our professor, Preetpal Kang for designing such a course where learning was his guidance and consistent feedback. We would also like to thank the ISA team for their valuable inputs as per their own experience of the course when taken and their support and motivation at every phase of this project. There were some unsung, selfless classmates who helped us whenever necessary, whenever any immediate hardware was required or any other guidance needed in spite of being from the rival teams. We would like to thank each one of them who forgot their differences or considered the course and project as a competition to selflessly help us when in need.

References Used

[1] Preetpal Kang's lecture notes of CMPE 244, Computer Engineering, San Jose State University, Jan-May 2018.

Appendix

You can list the references you used.