Difference between revisions of "S17: Boom-Z Equalizer"

Revision as of 23:09, 21 May 2017

Grading Criteria

How well is Software & Hardware Design described?
How well can this report be used to reproduce this project?
Code Quality
Overall Report Quality:
- Software Block Diagrams
- Hardware Block Diagrams
  Schematic Quality
- Quality of technical challenges and solutions adopted.

Project Title

Boom-Z Equalizer

Abstract

The purpose of this project is to allow the team to experiment with a sound reactive project. The team will use a specialized IC to convert the input audio signal into a digital signal that can be parsed by the SJSUone board. The team will also create the LED array grid that will be used to display the waveform/frequency representation of the audio signal. The final project should be able to take an input audio signal (using a regular audio cable/jack) and display some kind of frequency representation using the LED array grid.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

David Bui
Marvin Flores
Adam Iglesias
- LED Matrix
Mina Yi
- LED Matrix

Schedule

Week#	Date	Task	Actual
1	3/19	Delegate project tasks Prepare wiki Research implementation options Choose/order parts	Delegate project tasks - done Prepare wiki - done Research implementation options - done Choose/order parts - in progress
2	3/26	Complete software design phase Finish first draft diagrams Prepare freeRTOS tasks Read datasheets for the parts Begin PCB design	Complete software design phase - in progress Finish first draft diagrams - in progress Prepare RTOS tasks - in progress Begin PCB design - in progress
3	4/2	Implement software design Implement drivers Integrate LED matrix with its driver module Integrate graphic equalizer with SJSUone board and audio input Send PCB to be made	Implement software design - in progress Implement driver for MSGEQ7 - done Integrate LED matrix with its driver module - not yet started Integrate graphic equalizer with SJSUone board and audio input - done Send PCB to be made - in progress
4	4/9	Integrate LED matrix with the equalizer module via SJOne board	Reordered LEDS to be used. Found out LEDS used non-standard communication protocol. Soldered components to PCB. Implemented software design Equalizer part - done LED driver - in progress
5	4/16	Testing and Debug	Tested PCB (equalizer) Started interfacing new LEDs (SPI protocol) Started designing PCB for LEDs LED driver - in progress
6	4/23	Testing and Debug	PCB design LED - in progress LED driver - in progress task communication between Equalizer and LED driver - done
7	4/30	Testing and Debug	started LED prototype board (for backup)
8	5/7	Testing and Debug	LED PCB design finished and sent to shop
9	5/14	Testing and Debug	LED PCB received and started soldering
10	5/21	Ready for Demo Complete Project Report	Final Assembly/Integration of LEDs and Display Box

Parts List & Cost

Bill of Materials for Graphic Equalizer

#	Name	Purchase Location	Description	Quantity	Cost
1	MSGEQ7	[1]	7 Band Graphic Equalizer	2	$4.95
2	capacitor	HSC Electronics	.1 uF capacitor	7	$0.35
3	capacitor	HSC Electronics	33 pF capacitor	2	$0.40
4	capacitor	HSC Electronics	.33 uF capacitor	1	$0.35
5	capacitor	HSC Electronics	10 uF capacitor	1	$0.35
6	capacitor	HSC Electronics	100 nF capacitor	1	$0.35
7	resistor	HSC Electronics	200kΩ resistor	2	$0.05
8	resistor	HSC Electronics	22kΩ resistor	2	$0.05
9	power jack	HSC Electronics	power jack	1	$0.45
10	audio jack	HSC Electronics	audio jack	1	$0.45
11	voltage regulator	HSC Electronics	3V voltage regulator	1	$0.25
12	voltage regulator	HSC Electronics	5V voltage regulator	1	$0.25
13	male header pins	HSC Electronics	male header pins	1	$0.95

Bill of Materials for LED Matrix

#	Name	Purchase Location	Description	Quantity	Cost per item
1	LED Strip	Amazon	APA102C LEDs	1	$29.88
2	PCB	Bay Area Circuits	9.6" x 5"	1	$30
3	Shadowbox	Michaels	10" x 10", 4.5" depth	1	$32.99
4	Thin Plywood	Home Depot	9.5" x 9.5"	1	Varies
5	Power Supply	Amazon	Mean Well 5v 5A power supply	1	$13.22
6	3 Pronged Power Cord	Home Depot	Husky 8ft 3 pronged power replacement cord	1	$9.97

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Graphic Equalizer

The main purpose of the graphic equalizer is to be able to take an audio input and generate an ADC output signal. The output values will be used to drive the LED Matrix values. The team decided to use MSGEQ7 chip for its simple design and ease of use. The MSGEQ7 Graphic equalizer can take an audio signal and 'split' it into 7 different frequencies. The team used two MSGEQ7 chips to separate left and right audio signal; this allowed the team to have more column of frequencies to display in the LED matrix.

Figure 1. Strobe Timing Diagram

The board design is very straight forward. The strobe and reset source are the same on both MSGEQ7 chip; left and right audio input are split to each designated MSGEQ7 chip. The output for both chips are fed into the ADC inputs of the SJSUOne board. The real trick here is to write the software driver to parse the frequency outputs which will be discussed in the software implementation below.

Figure 2. Equalizer Schematic

LED Matrix

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

LED Matrix Design

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

Sourceforge Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.