Difference between revisions of "F16: Kasper"

Revision as of 06:47, 19 December 2016

Project Title

Self Driving Car

Abstract

We are in an era of smart machines. With the self driving cars taking over the roads these days, it is an interesting challenge to build our own version of it.
This project aims at the implementation of such a self-driving car.

It is based on CAN communication protocol which has been proven to be robust and deterministic by the automotive industry. The controller used is the SJ-One Board.

The overall driving of the car is divided across five modules:
Sensor: The sensor module essentially checks for obstacles in the driving path.
MotorIO: MotorIO drives the car using the underlying DC motor and Servo.
Geo: Geo controller is responsible for obtaining the location details and aid navigation.
Bridge: Bridge controller interfaces with the Android application where the path to be traversed is selected.
Master: Master co-ordinates the data from each of the modules and drives the MotorIO.

With all these implementations in place, the car will be able to drive itself to the destination.

Objectives & Introduction

Objective of this project is to create a self driving car

System Block Diagram

System block diagram

Team Members & Responsibilities

We have used five controllers

• Sensor Controller
  • Shruthi Narayan
  • Rimjhim Ghosh
  • Color coding: Text
• Motor & I/O Controller
  • Prashant Aithal
  • Chethan Keshava
  • Color coding: Text
• Geographical Controller
  • Ankit Gandhi
  • Color coding: Text
• Master Controller
  • Aajna Karki
  • Spoorthi Mysore Shivakumar
  • Color coding: Text
• Communication Bridge Controller
  • Bharat Khanna
  • Shantanu Vasishtha
  • Color coding: Text

Team Schedule

Parts List & Cost

DBC File Implementation

The DBC file used for the project is as below:

VERSION ""

NS_ :

 BA_
 BA_DEF_
 BA_DEF_DEF_
 BA_DEF_DEF_REL_
 BA_DEF_REL_
 BA_DEF_SGTYPE_
 BA_REL_
 BA_SGTYPE_
 BO_TX_BU_
 BU_BO_REL_
 BU_EV_REL_
 BU_SG_REL_
 CAT_
 CAT_DEF_
 CM_
 ENVVAR_DATA_
 EV_DATA_
 FILTER
 NS_DESC_
 SGTYPE_
 SGTYPE_VAL_
 SG_MUL_VAL_
 SIGTYPE_VALTYPE_
 SIG_GROUP_
 SIG_TYPE_REF_
 SIG_VALTYPE_
 VAL_
 VAL_TABLE_

BS_:

BU_: DBG MASTER GEO SENSOR MOTORIO BRIDGE

BO_ 100 STOP_CAR: 1 MASTER 
 SG_ STOP_CAR_data : 0|8@1+ (1,0) [0|0] "" BRIDGE,GEO,SENSOR,MOTORIO,DBG

BO_ 110 RESET: 1 MASTER 
 SG_ RESET_data : 0|8@1+ (1,0) [0|0] "" BRIDGE,GEO,SENSOR,MOTORIO,DBG 

BO_ 120 POWER_SYNC_ACK: 1 MASTER 
 SG_ POWER_SYNC_ACK_data : 0|8@1+ (1,0) [0|0] "" BRIDGE,GEO,SENSOR,MOTORIO,DBG 

BO_ 130 STOP_CMD_APP: 1 BRIDGE 
 SG_ STOP_CMD_APP_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 140 START_CMD_APP: 1 BRIDGE 
 SG_ START_CMD_APP_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 200 MOTOR_POWER_SYNC: 1 MOTORIO 
 SG_ MOTOR_POWER_SYNC_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 210 SENSOR_POWER_SYNC: 1 SENSOR 
 SG_ SENSOR_POWER_SYNC_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 220 BRIDGE_POWER_SYNC: 1 BRIDGE
 SG_ GEO_POWER_SYNC_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 230 GEO_POWER_SYNC: 1 GEO 
 SG_ BRIDGE_POWER_SYNC_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 300 MOTORIO_HEARTBEAT: 1 MOTORIO
 SG_ MOTORIO_HEARTBEAT_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG 
 
BO_ 310 SENSOR_HEARTBEAT: 1 SENSOR
 SG_ SENSOR_HEARTBEAT_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG 
 
BO_ 320 BRIDGE_HEARTBEAT: 1 BRIDGE
 SG_ BRIDGE_HEARTBEAT_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG 

BO_ 330 GEO_HEARTBEAT: 1 GEO
 SG_ GEO_HEARTBEAT_data : 0|8@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 400 SENSOR_SONIC: 4 SENSOR 
 SG_ SENSORS_SONIC_front_left : 0|8@1+ (1,0) [0|0] "" MASTER,MOTORIO,DBG
 SG_ SENSORS_SONIC_front_right : 8|8@1+ (1,0) [0|0] "" MASTER,MOTORIO,DBG
 SG_ SENSORS_SONIC_front_center : 16|8@1+ (1,0) [0|0] "" MASTER,MOTORIO,DBG
 SG_ SENSORS_SONIC_back : 24|8@1+ (1,0) [0|0] "" MASTER,MOTORIO,DBG

BO_ 410 MOTORIO_DIRECTION: 3 MASTER
 SG_ MOTORIO_DIRECTION_speed : 0|8@1+ (1,0) [0|10] "" MOTORIO,DBG
 SG_ MOTORIO_DIRECTION_turn : 8|8@1+ (1,-4) [-3|3] "" MOTORIO,DBG
 SG_ MOTORIO_DIRECTION_direction : 16|8@1+ (1,0) [0|2] "" MOTORIO,DBG

BO_ 420 BRIDGE_TOTAL_CHECKPOINT: 1 BRIDGE
 SG_ BRIDGE_TOTAL_CHECKPOINT_NUMBER : 0|8@1+ (1,0) [0|0] "" MASTER,MOTORIO,DBG

BO_ 430 RECEIVE_START_ACK: 1 MASTER
 SG_ RECEIVE_START_ACK_ack : 0|8@1+ (0,0) [0|0] "" BRIDGE,DBG

BO_ 440 BLUETOOTH_DATA: 8 BRIDGE
 SG_ BLUETOOTH_DATA_LAT : 0|32@1+ (0.000001,0) [0|0] "" MASTER,DBG
 SG_ BLUETOOTH_DATA_LON : 32|32@1+ (0.000001,0) [0|0] "" MASTER,DBG

BO_ 450 NEXT_CHECKPOINT_DATA: 8 MASTER
 SG_ NEXT_CHECKPOINT_DATA_latitude : 0|32@1+ (0.000001,0) [0|0] "" GEO,DBG
 SG_ NEXT_CHECKPOINT_DATA_longitude : 32|32@1+ (0.000001,0) [0|0] "" GEO,DBG

BO_ 460 COMPASS_DATA: 5 GEO
 SG_ COMPASS_DATA_speed : 0|8@1+ (1,0) [0|0] "" MASTER,DBG
 SG_ COMPASS_DATA_heading : 8|16@1+ (1,0) [0|0] "" MASTER,DBG
 SG_ COMPASS_DATA_bearing : 24|16@1+ (1,0) [0|0] "" MASTER,DBG

BO_ 470 CURRENT_LOCATION_ACK: 1 BRIDGE
 SG_ CURRENT_LOCATION_ACK_ack : 0|8@1+ (1,0) [0|0] "" MASTER,GEO,DBG

BO_ 480 GPS_LOCATION: 8 GEO
 SG_ GPS_LOCATION_latitude : 0|32@1+ (0.000001,0) [0|0] "" MASTER,BRIDGE,DBG
 SG_ GPS_LOCATION_longitude : 32|32@1+ (0.000001,0) [0|0] "" MASTER,BRIDGE,DBG

BO_ 490 DISTANCE_TO_DESTINATION: 1 GEO
 SG_ DISTANCE_TO_DESTINATION_data : 0|8@1+ (0,0) [0|0] "" MASTER, MOTORIO,DBG

BO_ 500 BATTERY_STATUS: 1 SENSOR
 SG_ DISTANCE_TO_DESTINATION_status : 0|8@1+ (0,0) [0|0] "" MASTER, MOTORIO,DBG

CM_ BU_ DBG "Debug node used to determine whether the message is received by any other node"; 
CM_ BU_ DRIVER "Master Controller";
CM_ BU_ SENSOR "Sensor Controller";
CM_ BU_ MOTORIO "Motor I/O controller";
CM_ BU_ BRIDGE "BRIDGE Controller";
CM_ BU_ GEO "Geo Controller";
CM_ BO_ 2 "Sync message used to synchronize the controllers"; 

BA_DEF_ "BusType" STRING ;
BA_DEF_ BO_ "GenMsgCycleTime" INT 0 0;
BA_DEF_ SG_ "FieldType" STRING;

BA_DEF_DEF_ "BusType" "CAN";
BA_DEF_DEF_ "FieldType" "";
BA_DEF_DEF_ "GenMsgCycleTime" 0;

BA_ "GenMsgCycleTime" BO_ 300	          1;
BA_ "GenMsgCycleTime" BO_ 310	          1;
BA_ "GenMsgCycleTime" BO_ 320	          1;
BA_ "GenMsgCycleTime" BO_ 330             1;
BA_ "GenMsgCycleTime" BO_ 400 	          10;
BA_ "GenMsgCycleTime" BO_ 410             10;        
BA_ "GenMsgCycleTime" BO_ 450             10;
BA_ "GenMsgCycleTime" BO_ 460             10;
BA_ "GenMsgCycleTime" BO_ 470             10;
BA_ "GenMsgCycleTime" BO_ 480             10;

Sensor Controller

Team Members & Responsibilities

• Shruthi Narayan
• Rimjhim Ghosh

Schedule

Hardware Design

4 Parallax Ping ultrasonic distance sensors are used for this project. They are used for obstacle detection and avoidance. Non-contact distance can be measured from about 2 cm (0.8 inches) to 3 meters (3.3 yards).

The PING))) sensor works by transmitting an ultrasonic burst and providing an output pulse that corresponds to the time required for the burst echo to return to the sensor. By measuring the echo pulse width, the distance to target can easily be calculated.

Four Sensors placed in the car, three in front (front_left, front_center, front_right) and one at the back (back). The image below shows the wired connections between sensors and SJOne board.

Sensor Hardware Interface block diagram

Sensors mounted on car

Software Design

Operation Squence:

Sensor Operation Flowchart

Software timer for triggering sensor:

All sensors are triggered using software timers. A soft timer is declared for each sensor which keeps track of the time between trigger and echo for that particular sensor.

#define Echo_Return_Pulse 18.5
SoftTimer ping_duration_left;
ping_duration_left.reset(Echo_Return_Pulse);
ping_duration_left.restart();

Hardware timer for calculating distance:

The declaration of hardware timer is as shown below:

lpc_timer_enable(lpc_timer0,1); /*enable timer0*/
lpc_timer_set_value(lpc_timer0,0); /*set timer0 value=0*/

Distance Calculation:

Distance=Speed * Time

The distance covered by the sound wave is twice the actual distance.

Therefore, Distance= (Speed * Time)/2

Speed of sound=340m/s, 1m=100cm, 1us=0.000001 s

Distance covered in 1us= (340*100*0.000001)/2 = 0.017cm

#define Distance_Scale 0.017
time_left = lpc_timer_get_value(lpc_timer0);
distance_left = (Distance_Scale)*time_left;

Ranging:

LeftSIG.setAsOutput(); /*make SIGpin output*/
LeftSIG.setLow(); /*set low for 2us and then high for clean high*/
delay_us(2);
LeftSIG.setHigh(); /* enable Ranging (enable left sonar). trigger/set high for 2 µs (min), 5 µs typical. Ultrasonic burst*/
delay_us(5);
LeftSIG.setLow(); /*set low*/
LeftSIG.setAsInput(); /*make SIGpin input*/

Implementation

Sensor Testing: LV-MaxSonar-EZ(MB1010):

• This sensor gives a range of 0 inches to 254 inches with a voltage supply of 5V.

• Using multiple ultrasonic sensors in a single system caused interference (crosstalk) so the sensors were triggered sequentially which reduced the fluctuating values

• The range reading time of Maxbotix LV-MaxSonar-EZ1 is 49 ms for a range of 254 inches (6.54 m) requirement was to send all sensor values in 10 Hz. Only 2 sensor values could be sent.

• Having the requirement to send the sensor readings in 10Hz, we reduced the delay between the sensors to 15ms covering a range of 101 inches. Send values of all the four sensors (left, center, right, back) in 10Hz using chaining process.

• Even after this there were frequent abrupt values encountered in the readings so considering the fluctuations and requirement we switched to parallax ping sensors.

Parallax Ping Sensor Testing:

Parallax Ping Sensor-Front View

Parallax Ping Sensor- Back View

Pin Configuration:

Pin1: GND- Ground pin

Pin2: 5V- Voltage Supply pin

Pin3: SIG- Signal Pin- This emits a short 40Khz burst acting as a trigger pin then the same pin starts listening the echo.

• Provides precise, non-contact distance measurements within a 2 cm to 3 m range • Simple pulse in/pulse out communication requires just one I/O pin • Burst indicator LED shows measurement in progress • 3-pin header makes it easy to connect to a development board, directly or with an extension cable, no soldering required • The PING))) sensor works by transmitting an ultrasonic (well above human hearing range) burst and providing an output pulse that corresponds to the time required for the burst echo to return to the sensor. By measuring the echo pulse width, the distance to target can easily be calculated.

Parallax Ping Sensor Coomunication Protocol

The PING))) sensor detects objects by emitting a short ultrasonic burst and then "listening" for the echo. Under control of a host microcontroller (trigger pulse), the sensor emits a short 40 kHz (ultrasonic) burst. This burst travels through the air, hits an object and then bounces back to the sensor. The PING))) sensor provides an output pulse to the host that will terminate when the echo is detected, hence the width of this pulse corresponds to the distance to the target.

Working of Parallax Ping Sensor

Testing & Technical Challenges

Issue 1: Triggering of Sensors in Parallel

Triggering all the sensors in parallel causes interference between adjacent sensors, which in turn causes mis-firing of echo. This results in incorrect distance values from all the sensors.

Solution: Sequential triggering of Sensors Each sensor is triggered only when the previous sensor receives an echo or exceeds the maximum echo reception wait time which is 18.5ms.

Issue 2: Sensor Angle The Left and Right sensors gave faulty values when placed at an acute angle on the corner of the base board.

Solution: angle>45 Increased the angle to cover wider area and avoid reflections. Increasing the angle to more than 45 degrees helped get us accurate values.

Motor & I/O Controller

Team Members & Responsibilities

• Chethan Keshava
• Prashant Aithal

Schedule

Motor/IO Controller Software Design

Tasks

Motor Pin Connections

The car battery accepts compatible Ni-MH batteries. The battery powers the ESC unit, which in turn drives the motor and also powers the steering servo. The SJ One board, ESC unit and steering servo should share a common ground in order for the PWM signals to have the same reference voltage. The CAN transceiver uses the 5V power supply and GND, as well as the P0.0 (CAN RX) and P0.1 (CAN TX) of the SJ One Board. P2.0 (PWM1) and P2.1 (PWM2) controls the steering and motor respectively. This is done by sending out PWM signals from the SJ One board that change the width of a 20ms period waveform. 1ms width represents a 0% duty cycle, 1.5ms width represents a 50% duty cycle, and 2ms width represents a 100% duty cycle.

Motor Controller Block Diagram

Software Flow Diagram

DC Motor

Servo Motor

Speed Feedback Encoder

The speed feedback is simply an rpm meter. It consists of a Hall Effect magnetic sensor with a set of magnets. The magnets are attached to the inner surface of the wheels and the sensor is connected to the end of the shaft connecting the wheel. Whenever the magnet comes near the sensor, a high signal is generated from the sensor and given to the GPIO port of the SJOne board, which is made as positive edge triggered. The interrupt handler would then increment a count which would give us revolutions per second if the above mentioned count is measured over one second (1Hz periodic callback function).

The next step would be to control speed with this calculated rpm. There are two conditions that need to be checked. One is the speed that the MASTER controller is sending (stop, slow, normal or fast) and another is the rpm. Each of the speeds would have a desired rpm and the calculated rpm is compared to the desired rpm and the final PWM signal to the DC motor is incremented or decremented depending on that. A scenario for this usage would be when the car encounters an upward ramp and the car would slow down while climbing to that. The algorithm would check and sense that the rpm has reduced and would modify PWM for DC to increase power and hence the rpm of car is kept at the desired range.

Liquid Crystal Display

IO is the mode of interaction between user and car peripherals. It includes touch screen GLCD and headlights. LCD displays the car status while the touch screen allows the user to shift between various modes. The touch screen GLCD uLCD32PTU has the following features Low-cost 3.2" LCD-TFT display graphics user interface solution. 240 x 320 VGA resolution, RGB 65K true to life colours, TFT screen with Integrated 4-Wire Resistive Touch Panel. Easy 5 pin interface to any host device: VCC, TX, RX, GND, RESET Powered by 4D-Labs PICASO processor. 2 x Asynchronous hardware serial ports (COM0, COM1), TTL interface, with 300 to 600K baud. On-board micro-SD memory card adaptor for multimedia storage and data logging purposes. HC memory card support is also available for cards larger than 4GB. 4.0V to 5.5V range operation (single supply).

The LCD is used to display vital parameters such as

• Speed
• Obstacle proximity
• GPS co-ordinates
• Current and heading compass zone

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Geographical Controller

Team Members & Responsibilities

• Ankit Gandhi

GPS, Compass firmware and Hardware Interfacing.

Schedule

Design & Implementation

Hardware Design

Components

SJOne Board

Ultimate GPS

The breakout is built around the MTK3339 chipset, a no-nonsense, high-quality GPS module that can track up to 22 satellites on 66 channels

• 512K ROM, 64K(96K) RAM, 1M(2M) SPI Flash, and Micro-SD for storage.
• Arm Cortex-M4 variant contains 96K RAM, and 2Mb SPI flash
• 2-Digit 7-Segment Display
• Power from USB or External Power
• Many GPIOs with two SPI, Multiple UARTs, and I2C and CAN availability

GPS Module

Ultimate GPS

The breakout is built around the MTK3339 chipset, a no-nonsense, high-quality GPS module that can track up to 22 satellites on 66 channels

• -165 dBm sensitivity, 10 Hz updates, 66 channels
• 5V friendly design and only 20mA current draw
• RTC battery-compatible
• Internal patch antenna + u.FL connector for external active antenna

The Compass Module - LSM303DLHC

Compass

Compass module is based on ST Micros LSM303. When current flows through a wire, a magnetic field is created. This is the basic principle behind electromagnets. This is also the principle used to measure magnetic fields with a magnetometer. The direction of Earth's magnetic fields affects the flow of electrons in the sensor, and those changes in current can be measured and calculated to derive a compass heading.

The features of LSM303DLHCare:

• Simple I2C interface
• 3 magnetic field channels and 3 acceleration channels
• ±2g/±4g/±8g/±16g linear acceleration full scale
• From ±1.3 to ±8.1 gauss magnetic field full scale

Following is the Geo Controller system diagram

Hardware Interface

Below table lists all the hardware pins used in Geo Controller

RD
TD
Vcc
GND 

RD1 P0.0
TD1 P0.1
5V
GND

Rx
Tx
Vcc
GND 

TXD2 P2.8
RXD2 P2.9
5V
GND

SDA
SCL 
Vcc
GND

SDA2 P0.10
SCL2 P0.11
Vcc
GND

Software Design

• Initialization

GPS module is interfaced using UART. UART is initialized using the most common configuration 9600/8-N-1(9600 baudrate, 8 databits, no (N) parity bit, and  :one (1) stop bit.

We are using LSM303DLHC compass module. Both GPS and Compass modules are initialized as below.

 void geotaskInit()
 {
     gpsUart.init(GPS_BAUD_RATE,rx_q,tx_q);   // Initialize UART for GPS
     LSM_MAG.init();                          // Initialize LSM303 Magnetometer 
     LSM_ACCL.init();                         // Initialize LSM303 Accelerometer
 }

• Data Communication with GPS and Compass

GPS

GPS module is programmed to send GPS data at 10Hz. Interrupt Handler continuously receives these data and stores in the queue.

Periodically (10Hz) calling the getChar function gives a complete NMEA string.

Following string is used to set NMEA output sentence, we are using GPRMC for this project(Done in initialization)

char gpsRMConlyCommand[] = "$PMTK314,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0*29\r\n";
char gpsOutputFrequency[] =  "$PMTK220,100*2F\r\n";

After sending this, we will be getting GPS string after every 10Hz, which is read by interrupt handler.

Angle between two coordinates

Compass

Compass data is read and send every 10Hz. Compass data consists of Bearing, Distance and Heading

Bearing Calculation:

Bearing angle between two GEO coordinates is calculated using following formula

θ = atan2( sin Δλ ⋅ cos φ2 , cos φ1 ⋅ sin φ2 − sin φ1 ⋅ cos φ2 ⋅ cos Δλ )
  where, φ1,λ1 is the start point
  φ2,λ2 the end point 
  (Δλ is the difference in longitude) 

Bearing

Distance Calculation:

Distance between two GEO coordinates is calculated using following formula

a = sin²(Δφ/2) + cos φ1 ⋅ cos φ2 ⋅ sin²(Δλ/2)
c = 2 ⋅ atan2( √a, √(1−a) )
d = R ⋅ c
  where φ is latitude, λ is longitude, 
  R is earth’s radius (mean radius = 6,371km);

• CAN Communication

In GeoController, we are using can1 for transmitting and receiving can messages. Latitude and longitude values are getting updated periodically.

  void geoTask::sendGpsData()
  {
      if(recvdTrueGPSData == true)
      {
          GPS_LOCATION_t geoGpsData = { 0 };
          geoGpsData.GPS_LOCATION_latitude = curLatitude;
          geoGpsData.GPS_LOCATION_longitude = curLongitude;
          u0_dbg_printf("lat : %f lon: %f\n",curLatitude,curLongitude);
          // This function will encode the CAN data bytes, and send the CAN msg using dbc_app_send_can_msg()
          dbc_encode_and_send_GPS_LOCATION(&geoGpsData);
          recvdTrueGPSData = false;
      }
   }

  void geoTask::sendCompassData()
  {
      COMPASS_DATA_t geoCompassData = { 0 };
      calculateDistance();
      if(newChkPointRecvd)
      {
          calculateBearing();
          newChkPointRecvd = false;
      }
      LSM_MAG.getHeading(&heading);
      geoCompassData.COMPASS_DATA_bearing = bearing;
      geoCompassData.COMPASS_DATA_heading = heading;
      geoCompassData.COMPASS_DATA_speed = speed;
      geoCompassData.COMPASS_DATA_distance = distance;
      u0_dbg_printf("head: %f,bearing:%f,Dis:%.2f\n",heading,bearing,distance);
      // This function will encode the CAN data bytes, and send the CAN msg using dbc_app_send_can_msg()
      dbc_encode_and_send_COMPASS_DATA(&geoCompassData);
   }

Geo Software Flow Diagram

Geo software flowdiagram

Testing & Technical Challenges

1. Compass Calibration

Initially compass doesn't give correct readings,compass needs to be calibrated before it can be used. -->Used following Arduino sketch to get the minimum and maximum readings of the compass on all three axes.

void loop() 
{  
   compass.read();
   running_min.x = min(running_min.x, compass.m.x);
   running_min.y = min(running_min.y, compass.m.y);
   running_min.z = min(running_min.z, compass.m.z);
   running_max.x = max(running_max.x, compass.m.x);
   running_max.y = max(running_max.y, compass.m.y);
   running_max.z = max(running_max.z, compass.m.z);
   snprintf(report, sizeof(report), "min: {%+6d, %+6d, %+6d}    max: {%+6d, %+6d, %+6d}",
   running_min.x, running_min.y, running_min.z,
   running_max.x, running_max.y, running_max.z);
   Serial.println(report);
   delay(100);
}

Use of these Minimum and Maximum Values in the calculation gives better readings

Another issue with compass is tilt compensation. If compass is tilted it gives wrong readings. Tilt needs to be compensated using Accelerometer readings.

pitch = asin(-accxnorm);
roll = asin(accynorm/cos(pitch));
where accxnorm and accynorm are normalized x and y acceleration vector respectively.

Communication Bridge Controller

Team Members & Responsibilities

• Bharat Khanna
• Shantanu Vashishtha

Schedule

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Bluetooth Module

Bluetooth Module

RN42XV is built around Microchip's RN42 low power Bluetooth module. Some features of this module are as follows

• Based on the popular 2 x 10 (2mm) socket footprint.
• Voltage range: (3-3.6)Volts
• Current range: 26 μA sleep, 3 mA connected, 30 mA transmit.
• UART data connection interface.
• Sustained data rates: 240 Kbps (slave), 300 Kbps (master)
• Transmission range up to 60 feet (20 m) distance, +4 dBm output transmitter, -80 dBm typical receive sensitivity.
• FHSS/GFSK modulation, 79 channels at 1-MHz intervals.

Hardware Design

Hardware Interface

Pinout Bridge Controller

Table CAN Message and_Message ID

Bluetooth Software Design

The main ffunctions that are used for communication are as follows.

void Check_Start_STOP__CheckPoint_Condition()
{
	if(strcmp(stored_Bluetooth_data,START) == 0)
	{
		START_CONDITION.START_CMD_APP_data = 1;
		dbc_encode_and_send_START_CMD_APP(&START_CONDITION);
		memset(stored_Bluetooth_data, 0, sizeof(stored_Bluetooth_data));
	}
	else if(strcmp(stored_Bluetooth_data,STOP) == 0)
	{
		STOP_CONDITION.STOP_CMD_APP_data = 1;
		dbc_encode_and_send_STOP_CMD_APP(&STOP_CONDITION);
		memset(stored_Bluetooth_data, 0, sizeof(stored_Bluetooth_data));
	}
	else if(check_received == true)
	{
		int loop =0;
		BRIDGE_TOTAL_CHECKPOINT.BRIDGE_TOTAL_CHECKPOINT_NUMBER = check_point_total;
		dbc_encode_and_send_BRIDGE_TOTAL_CHECKPOINT(&BRIDGE_TOTAL_CHECKPOINT);
		for(loop = 0; loop < (check_point_total*2) ;loop=loop+2)
 		{
			BLUETOOTH_DATA_Location.BLUETOOTH_DATA_LAT = store_cor[loop];
			BLUETOOTH_DATA_Location.BLUETOOTH_DATA_LON = store_cor[loop+1];
			dbc_encode_and_send_BLUETOOTH_DATA(&BLUETOOTH_DATA_Location);
		}
		check_received = false;
	}
 } 

void Can_Receive_ID_Task()
{
	if (CAN_rx(can1, &can_msg_Info, 0))
	{
		LE.off(1);
		dbc_msg_hdr_t can_msg_hdr;
		can_msg_hdr.dlc = can_msg_Info.frame_fields.data_len;
		can_msg_hdr.mid = can_msg_Info.msg_id;
		if(can_msg_Info.msg_id == RESET_HDR.mid)
			dbc_decode_RESET(&REST_Info, can_msg_Info.data.bytes, &can_msg_hdr);
		if(can_msg_Info.msg_id == RECEIVE_START_ACK_HDR.mid)
			printf("Case_RECEIVE_START_ACKt\n");
		if(can_msg_Info.msg_id == BRIDGE_POWER_SYNC_HDR.mid)
			printf("BRIDGE_POWER_SYNC_data\n");
		if(can_msg_Info.msg_id == GPS_LOCATION_HDR.mid)
		{
			dbc_decode_GPS_LOCATION(&GPS_LOCATION_RECEIVE, can_msg_Info.data.bytes, &can_msg_hdr);
			sprintf(lat,"%f",GPS_LOCATION_RECEIVE.GPS_LOCATION_latitude);
			sprintf(lon,"%f",GPS_LOCATION_RECEIVE.GPS_LOCATION_longitude);
		        Send_App_curr_loc(lat,lon);
		}
		if(dbc_handle_mia_RESET(&REST_Info, 1))
		{
			REST_Info.RESET_data=RESET__MIA_MSG.RESET_data;
			LD.setNumber(REST_Info.RESET_data);
			LE.on(1);
		}
	}
}

Bluettoh Software FLow Chart

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Android Application Design

Problem statement

In present day, what is that one thing, which has become an essential part of a human life? Yes, that's correct, the answer is smartphone. It is almost impossible to imagine a single day without a mobile phone. So whether it is for a bank transaction or daily grocery shopping or travel, we need all the updated information in our hand. Keeping in mind this technological need, an application to control and track our self driving car prototype makes total sense. With universality of android platform, we decide to make an adnroid application to control our self driving car prototype "Kasper".

Implementation

The objective of the Android application is to allow the user to communicate with the self driving car using a smartphone. The application is built using Android Studio. It is the official IDE for Android platform development. The project uses .java file to design the logic of the app. To integrate maps within your application, an API key from Google's developer console is required. This API helps Google in tracking the statistics related to the app. When a device is clicked, map pops up which means that map fragment has been successfully implemented. Application uses Android Application framework (API level 25). There are four activities responsible for complete functionality of the application, namely FirstActivity.java, MapActivity.java and LatLong.java.

1. FirstActivity.java is responsible for screen 1 and has some basic buttons to "Turn ON" bluetooth for the device, find available bluetooth devices, make the smartphone discoverable to other devices, list paired devices and "Turn OFF" bluetooth on the device. After selecting an appropriate bluetooth module listed in the paired devices/available devices list, application makes a transition to screen 2.

2. The most basic information that a user must be able to control in a self-driving car is the source and the destination. The source in the application is designed to set with the current location sent by GPS module to bluetooth controller. Screen 2 is controlled by MapActivity.java that opens a map. This file is responsible for creating a bluetooth socket that allows communication between the app and the actual hardware. After the map is visible, destination is marked manually by the user, by selecting a point on the integrated Google map API. The format of the point selection is such that the application will consider the final/last checkpoint as destination while the rest markers will be considered as intermediate checkpoints. Once the user is done marking the check points, the information is sent to Bluetooth controller in the following format:
n,latitude_1,longitude_1...latitude_n,longitude_n
Here, n is number of checkpoints and (latitude_n,longitude_n) will be considered as the destination points by the Bluetooth controller. Once this information is sent, application waits for an acknowldgement in the form of "ack$" from the Bluetooth controller to ensure that the coordinates have been received. If there is no acknowldgement then the start button will not become active. After receiving acknowledgement, start button becomes active and the car will start moving when the button is asserted. Also, at a time only one of the two start or stop button is active. So, once a start button is pushed it is deactivated and stop is active now.
MapActivity.java also includes a handler for receiving messages like current location and then updating them on the map. It also receives coordinates at regular intervals to track the car location.

3. LatLong.java file has a public class with variables and methods that can used anywhere. This is done to set and get the latitude and longitude values.

Bluetooth - Android Interface

Command format and functionality

Application workflow

Application features

Android application has major features that exploit real time data. Once the phone is connected to the bluetooth module application starts sending and receiving data to perform number of operations. Features are listed below:
1. First feature is to get the current location. Application sends a command to request bluetooth module for updating the current location. After receiving the current location coordinates, application updates them on the Google map API used.
2. Second remarkable feature is updating the map with destination along with check points. This feature is highly desirable as it maps real life situation, in which destination is not reached instantly, but going from one checkpoint to another. Once the checkpoint have been marked they are sent to the master controller.
3. Third feature provide a layer of reliability during communication. Once the checkpoints have been sent, start car button will not become active until there is an acknowldgement from the bluetooth controller that it has received the destination coordinates along with checkpoints. This ensures that the car will not go to any random location.
4. The fourth most important feature in the application is that it exploits the real time data sent by the GPS module. As the car starts moving, GPS coordinates change. This new data is received by the application that helps in tracking the current car location. This feature is extremely useful to trace the route that is taken by the car (if there is any obstacle in the initial path).

Android UI design

Source code

Testing

• For testing purpose, * The code is made modular which means that each functionality in the code is defined in different functions. This approach makes it easier to check the output at different levels, which makes it easier to verify the output at different levels.
• The testing for Bluetooth module is done using "Bluetooth Serial Terminal" Application

Technical Challenges

• Technical challenge faced while communicating between Android app and Bluetooth was sending the current location which is achieved by updating the send_cor_buffer after every 10 milliseconds and sending updated coordinates.

Master Controller

Team Members & Responsibilities

• Aajna Karki
• Spoorthi Mysore Shivakumar

Schedule

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Master Controller is interfaced to CAN transceiver as shown below

Master Controller interface to CAN transceiver

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Below is the detailed flowchart of Obstacle and Navigation Algorithm

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Few challenged faced while implementing are as below

1. Make sure the system has only one CAN Receive. Let the values be populated in 100Hz and used in 1Hz/10Hz based on priority. Having more than one CAN can lead to confusions and hence may also miss messages.

2. When reading messages in 100Hz , read the CAN messages and use a if instead of while so that you avoid the chances of it to overrun.

My Issue #1

Discuss the issue and resolution.

Conclusion

The self driving car project has definitely helped us learn and grow in terms of technical knowledge as well as team management. Right from choosing the hardware components by considering every aspect of its functionality to programming them, this project has indeed given us an end-to-end learning of the entire system. There has been a lot of decision making which has resulted in many brain-storming sessions with the team as a whole.

The different phases of the project have been significant in their own terms. Selection of hardware is of utmost importance. We have had scenarios where we changed the ultrasonic sensors and the RPM sensors for greater accuracy. A major learning is that component selection needs diligent efforts. Sticking to the demo timelines would help a great deal. Code reviews would be beneficial as well.

We, as a team, have learnt how to build a machine from scratch. We also have learnt how a considerably big team can manage their particular modules and co-ordinate with the other modules as well. Team management has been a good takeaway here.

It has been overall a tremendous learning experience. I hope the further projects benefit from our learning curve documented.

Project Video

Upload a video of your project and post the link here.

Project Source Code

• Gitlab Source Code Link

References

Acknowledgement

This project has been an amazing learning experience for the whole team. The knowledge we take from here is immense. We are grateful to our Professor Preetpal Kang for his guidance and efforts towards making our learning commendable. Also, we would like to extend our sincere thanks to the ISA team for their continuous support. Here is a special mention to the Kasper team for all their meticulous and diligent efforts towards making this project a reality.

References Used

List any references used in project.

[1] Preetpal Kang's lecture notes of CMPE 243, Computer Engineering, San Jose State University, Aug-Dec 2016. 
[2] Fall 2014 Wiki Projects
[3] LPC1758 User Manual
[4] Parallax Ultrasonic Sensor
[5] CAN Transceiver
[6] Razor IMU
[7] LSM303 Application Note
[8] Adafruit Ultimate GPS Breakout - 66 channel w/10 Hz updates - Version 3
[9] GPS data calculation accuracy
[10] GPS Longitude Latitude distance calculator
[11] Calculate distance between two points
[12] GLCD with Touchscreen
[13] GPS Datasheet

Appendix

You can list the references you used.