PCB Top Layer

PCB Bottom Layer

BRD Image

Elegoo Power Supply Module

Rather than supplying power to the SJ-two board, led matrix, and MP3 decoder separately we decide to use the Power supply Module that came with the ELEGOO Upgraded Electronics Fun Kit. This supply module accepts input through a barrel jack from a battery, a 12V adapter, or any other source, and provides to our circuit a 5V as per our requirements. This module provides an inexpensive and convenient way to convert a 7-12V wall bug into 5V and 3.3V to power a solderless breadboard setup. The maximum output current is 700mA. One 5V connecter will go to the Vcc of the SJ-two board whereas 5V will be used to drive the 64x64 led matrix.

Power Module

LED Matrix and Controller Board Enclosure

We designed our LED matrix enclosure and controller board enclosure from the boxes available to us. To give the player the maximum immersive experience we have placed our matrix at an angle. The player can sit back, relax and play the arcade game quite easily as the controller board is not connected to the matrix enclosure. The controller board has its own enclosure and the communication between the board takes place through the XBee module.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

MP3 Decoder

This module is a kind of simple MP3 player device which is based on a high-quality MP3 audio chip---YX5300. It can support 8k Hz ~ 48k Hz sampling frequency MP3 and WAV file formats. There is a TF card socket on board, so you can plug the micro SD card that stores audio files. MCU can control the MP3 playback state by sending commands to the module via the UART port, such as switching songs, changing the volume, etc.

Image of MP3 Decoder board used in our project from Amazon

Hardware Design

The MP3 decoder module uses 4 pins namely UART Tx, UART Rx, VCC, and GND. The module required 3.3V to power up which has been supplied from the SJ2 board. We have configured UART1 pins on the SJ2 board for sending commands to the decoder. The baud rate for this UART communication has been set to 9600 bps. This decoder also has a 3.5mm audio jack that has been connected to a speaker.

Connection diagram of MP3 decoder to SJ2 board.

Software Design

MP3 Initialization

The command that we are using in our Bubble Trouble project is to play the music by accessing its index from the SD card. The function that sends this command is called play_music_at_index in our code. Before sending the command to play music at a certain index, we need to send the command [Select device] first. Serial MP3 Player only supports micro SD cards, so you should send “7E FF 06 09 00 00 02 EF” as described in the datasheet. Also, the commands are being sent using UART1 and the function uart__polled_put.

MP3 Flowchart

Implementation

Controller Board and Main Board Communication

With an XBee Explorer connected between your computer and your XBee, and with the help of the X-CTU software, you can easily configure XBees, test connections, and pass data between your computer and remote XBees. X-CTU is free software, provided by Digi (the manufacturer of XBee), which we use to configure and manage XBees and test XBee networks. The SparkFun website linked, here, gives a perfect step-by-step guide to configuring the Xbees as transmitter and receiver. The controller board consists of the joystick, button press, and Xbee module. The character movement is controlled using a joystick whereas the button presses the shoot arrow. The joystick reading using is taken using ADC. Rather than reading a single value every time we have to enable burst mode on ADC that does repeated conversion at 400khz.This data is then sent from the controller board over to the mainboard (the one that has the game logic and led drivers) using Xbee. After the data is received at the receiver end it is sent over UART. The A0-A6 bits of the UART frame is the joystick ADC reading whereas the A7 bit of the frame is the button pressed data. If the button is not being pressed then blank data is sent. A UART interrupt is generated, which invokes an ISR which sends data into the queue. Now the task that is sleeping on the queue wakes up and depending on the data does the character movement.

Depiction of Communication Between Boards

Game Logic

Ball Trajectory

Bubble shooter uses an intelligent mechanism for the ball jumping. This makes user perceive the game ball jumping almost as real ball jumping and give them the best playing experience. In order to achieve that we have designed a ball jumping logic that follows a parabolic equation. The parabolic equation and graph are shown below:

Ball Trajectory Graph

As the game starts, we have set some initial ball coordinates from where the ball starts its trajectory. By using these staring coordinates of row and column, we then derive the parabolic path which this ball will follow. For deriving the equation, we have used 3 variables, which play the role of the start point slope, curvature and the height of the ball jump. These variables are defined as below: Height Offset (z) As the name suggests, it is the distance between the maximum height our ball will jump and the upper wall. With ball size, its tendency to jump changes. So heavier ball jumps more as compared to light ball and we change height offset accordingly. Curvature (b)  This decides the curvature of the trajectory. By increasing its value, the parabola keeps getting flat. We have given a constant value for this variable. Start (a) This value basically means which trajectory our ball will follow if given a start point coordinates, curvature and height offset. It is one of the most important variable as we update this variable, whenever we want to change the trajectory of the ball.

When ball is moving forward:

(sqrt((row - height_offset) * 5) + col);

When ball is moving backwards:

(sqrt((row - height_offset) * 5) + col);

Once the variables are defined, we now get the row coordinates by incrementing the column coordinates and feeding that to the derived parabolic equation which further updates the row coordinates.

void parabolic_curve(int *row, int column, int start, int height_offset) {
  *row = (((column - start) * (column - start)) / 5) + height_offset;
}

Now, this methodology was enough to make the ball seem a little close to the parabolic curve. However, on 64x64 LED matrix this did not seem to be an exact parabola and gives stairs like curvature. In order to solve this problem, we designed an algorithm to only display when there is a change in a row while columns keep incrementing. By doing this, our ball does not follow a ramp pattern and seems to be moving in a parabolic slope.

Arrow Shooting and Ball Splitting

As discussed, when received MSB as high, it means the button is pressed and our character shoots an arrow thread in the air. This arrow splits the ball into two equal halves. Once the arrow coordinates match the ball coordinates, collision is detected and the ball is split into two halves. Below is how it is implemented.

Ball Trajectory Graph

Character Movement and Ways character can lose a life

Character movement is detected using values read from a remote Joystick. This character can shoot an arrow but also can get out if one of the below scenarios occur:

Character movement

Scoring

Scoring in the game is based on two factors. One, when the arrow shoots the ball and another is based on the timer left when the level is passed. Below is the game logic:

Scorecard Logic

Game Tasks

The figure below shows the FreeRTOS tasks that have been used in the Bubble Trouble game.

Game Tasks

Testing & Technical Challenges

1) We encounter an issue during the initial phase of the project where the 33rd row of the LED matrix was being displayed on the first row. This issue was happening because we were not resetting the Output Enable pin of the LED Matrix before clocking in the next row of data. We were able to resolve this issue after thoroughly reading the Sparkfun article on RGB Matrix Panels.

2) The main game logic of our game revolves around the concept of how balls bounce in the game. We could have developed a linear ball-bouncing logic. However, in order to make the ball bounce more realistic, we decided to resort to developing a parabolic ball jumping logic. This might sound easy at first, but, it was quite difficult to develop the logic. We had to take into consideration three cases viz. ball start logic, ball hitting the ground and bounce logic, and ball bouncing the “wall” that is the side of the back after hitting the screen. This challenge was time-consuming as it required us to carry out multiple permutations and combinations of values w.r.t the rows and columns of the led matrix and then display it on the screen. We did multiple iterations until we reached a smooth jumping pattern. Another challenge was to start two different parabolic functions after the arrow hit the ball. It was quite enjoying task as it refreshed out undergraduate mathematics geometry and algorithm thinking.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

• Sourceforge Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix