Difference between revisions of "F20: Jubeat"

Revision as of 03:57, 28 November 2020

Game photo

Introduction

Jubeat is a music game uses an arrangement of a 3x4 grid for the game play. An animation pops up on each grid according to the beat of the song. The player has to use his fingers to tap on the screen and catch the animation in time. Different scores will be given depending on when the player catch the animation. Tapes can be judged as PERFECT, GOOD, OK, and MISS.

Objectives & Introduction

This system:

1. Recognizes finger touch as the input to record the score.

2. Supports real time capacitive touch detection on a LED matrix display.

3. Update corresponding score on the LED display.

4. Outputs the audio via a mp3 module and the soundtracks are stored in an SD card.

Team Members & Responsibilities

Ka In Ng
- Git Admin
Tyler Tran
Srikar Narapureddy

Schedule

Week#	Date	Task	Status
0	10/13/2020	Read Past projects to get some design ideas Finalize our choice of game Game Design Confirm functionalities of the game Decide the parts & material for our project	completed completed completed completed completed
1	10/21/2020	Study previous projects Create project Wiki page Order parts	completed completed completed
2	10/28/2020	Acquire & test all parts and sensors Review Datasheet of the capacitive sensor Review Datasheet of the LED Matrix Review Datasheet of the mp3 player module	completed completed completed completed
3	11/4/2020	Draw schematic Create Git repository Capacitive touch sensor detects finger tapes Audio module plays the music from SD card Develop Driver for LED matrix. Develop Driver for capacitive touch matrix.	Completed Completed Completed Completed Completed in progress
4	11/11/2020	Develop Driver for audio. Test and debug the driver functionality. Design basic game animations. Design basic game flow and logic with each capacitive sensing activity. Draw state diagram	Completed in progress Completed Completed Completed
5	11/18/2020	Integrate Game logic with music and animations. Fine tune game timings and scoring Design PCB and game enclosure.	Not started
6	11/24/2020	Integrate Game logic with music and animations. Design menu screens, song selection Design and add frequency based animations	Not started in progress Completed
7	12/1/2020	Test & bug fix Continue fine tuning timing and logic Improve and add animations as necessary	Not started
8	12/8/2020	Prepare Final Project DEMO Wrap up Wiki page & Project submission	Not started

Parts List & Cost

Part Name	Part Model & link	Quantity	Cost Per Unit
Evaluation Board	SJ2 board (NXP LPC4078 MCU)	1	$50
64x64 RGB LED Matrix	3mm Pitch - 192mm x 192mm	1	$59.95
5V Power Supply	Aclorol 5V 5A 25W AC-DC	1	$13.19
12-Key Capacitive Touch Sensor	Adafruit MPR121	1	$7.95
ITO (Indium Tin Oxide) Coated PET Plastic	ITO Coated PET Plastic 100mm x 200mm	2	$9.95
DFPlayer Mini	MakerHawk DFPlayer Mini	2	$3.99
Speaker	3" Diameter - 4 Ohm 3 Watt	2	$1.95

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

Sourceforge Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.

@@ Line 1: / Line 1: @@
 == Game photo ==
-== Project Title ==
 == Introduction ==
@@ Line 7: / Line 7: @@
 == Objectives & Introduction ==
-Show list of your objectives.  This section includes the high level details of your project.  You can write about the various sensors or peripherals you used to get your project completed.
+This system:
+. Recognizes finger touch as the input to record the score.
+. Supports real time capacitive touch detection on a LED matrix display.
+. Update corresponding score on the LED display.
+. Outputs the audio via a mp3 module and the soundtracks are stored in an SD card.
 === Team Members & Responsibilities ===