Difference between revisions of "S18: Spybot"

Revision as of 02:12, 23 May 2018

Grading Criteria

How well is Software & Hardware Design described?
How well can this report be used to reproduce this project?
Code Quality
Overall Report Quality:
- Software Block Diagrams
- Hardware Block Diagrams
  Schematic Quality
- Quality of technical challenges and solutions adopted.

Project Title

Spybot

Abstract

The team will develop a RC car driven remotely with an Android smartphone. The RC car will be equipped with a camera to provide real-time visual feedback to the smartphone. The camera will also be mounted on a servo to add the capability to change the camera angle. The SJOne will be used to drive the motor and servo of the car in addition to the camera’s servo. The Android smartphone will communicate with the SJOne using Bluetooth. The Android smartphone will be used to command the SJOne and drive the car and motorized camera. The SJOne will stream visual data to the Android smartphone.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

YuYu Chen
- Android app & bluetooth communication
Jason Tran
- PCB design & RC car firmware
Sophia Quan
- Servo camera mount and camera integration
Andrew Javier
- Camera integration
Jeremy Chau
- Camera integration

Schedule

Week#	Date	Task	Status
1	04/15/2018	Able to communicate with Bluetooth module on MCU by end of the week	Completed
2	04/22/2018	Start on Android application and have UI finished by end of week Research possible ways to display live video feed in Android application	Completed
3	04/29/2018	Establish Bluetooth communication with Android App and MCU Start PCB design Start on motor and servo(s) controller Install MotionEyeOS and get familiar with the UI	Completed
4	05/06/2018	Test Android app communication with RC car Test RPi Camera with MotionEyeOS on multiple devices Get camera servo up and running by end of week	Completed
5	05/13/2018	System Integration and testing	Completed
6	05/20/2018	System testing	Completed

Parts List & Cost

Quantity	Vendor	Item	Price
1	San Jose State University	SJ One Board	$80.00
1	Adafruit	Raspberry Pi Zero W Camera Pack	$44.95
1	Traxxas	Traxxas Stampede: Monster Truck	$199.95
1	ITead	BTBee Pro	$12.50
1	Servo camera mount	[1]	$6.50
Total			$337.37

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Servo Motor

The servo motor is used as a camera mount for the Raspberry Pi camera. It uses a PWM signal and the percentage of how much the servo should pan or tilt is supplied by the Android application

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

<Bug/issue name>

Discuss the issue and resolution.

Raspberry Pi Camera Ribbon

The ribbon used for the camera to communicate with the RPi is very sensitive. While testing out the camera and its settings, the video feed would cut out a lot when the ribbon was disturbed. There were times when the camera would not be detected at all. To remedy this issue, the connection was gently redone until the video feed returned.

Connecting to the Pi Zero W

Initially, the group wanted to have the phone to connect to the Raspberry Pi through Wi-Fi. However, when setting up the Pi to be a Wi-Fi host, the phones could not discover the Pi making communication impossible. Furthermore, it did not allow the Pi to initially boot up properly. To rectify this problem, the group decided to have the mobile phone with the application be a hotspot host. While this means that the Pi would have to be reconfigured every time it wants to connect to a new phone, the results would be consistent with the feed from the camera being able to broadcast to the host phone.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

Sourceforge Source Code Link

References

Acknowledgement

Preetpal Kang
Khalil Estell

References Used

List any references used in project.

MotionEyeOS Source Code

Appendix

You can list the references you used.

@@ Line 149: / Line 149: @@
 <p> </p>
 === Raspberry Pi Camera Ribbon ===
-The ribbon used for the camera to communicate with the RPi is very sensitive.  While we were testing out the camera and its settings, the video feed would cut out a lot when the ribbon was disturbed. There were times when the camera would not be detected at all. To remedy this issue, we would gently redo the connection until the video feed returned.
+The ribbon used for the camera to communicate with the RPi is very sensitive.  While testing out the camera and its settings, the video feed would cut out a lot when the ribbon was disturbed. There were times when the camera would not be detected at all. To remedy this issue, the connection was gently redone until the video feed returned.
 === Connecting to the Pi Zero W ===