Difference between revisions of "F16: Seismograph"

From Embedded Systems Learning Academy
Jump to: navigation, search
m (Acknowledgement)
m (Testing & Technical Challenges)
Line 127: Line 127:
  
 
=== Documentation Issues ===
 
=== Documentation Issues ===
 +
One of the largest deterrents in our project was due to poor or little to no documentation.
 +
===== Working with the ST7735 =====
 
There were problems initializing the LCD screen since the documentation was not very helpful. In addition, the board was originally intended to be used with an Arduino so we had to port the Arduino code over to work with our board.
 
There were problems initializing the LCD screen since the documentation was not very helpful. In addition, the board was originally intended to be used with an Arduino so we had to port the Arduino code over to work with our board.
 +
 +
===== HC-06 Bluetooth Module =====
 +
 +
=== Bus Contention Issues ===
  
 
== Conclusion ==
 
== Conclusion ==

Revision as of 05:41, 19 December 2016

Grading Criteria

  • How well is Software & Hardware Design described?
  • How well can this report be used to reproduce this project?
  • Code Quality
  • Overall Report Quality:
    • Software Block Diagrams
    • Hardware Block Diagrams
      Schematic Quality
    • Quality of technical challenges and solutions adopted.

Project Title

Seismograph

Abstract

In recent years, news of an upcoming large scale earthquake in California has been increasing. Having a seismograph would allow us to directly see any seismic activity. In addition, by adding an LCD screen, we would be able to add plots of the data in a time series manner for any research purposes. Most importantly, the seismograph device would allow to help with search and rescue efforts. When a large scale earthquake is detected, it would allow a signal to be detected via your cellphone in order to ping your GPS location in case of a building collapse.

Objectives & Introduction

Our seismograph would help bring awareness to the realities of earthquakes in California. In addition, it has the possibility to help save lives by aiding in search and rescue efforts when a large earthquake does come.

  • Create a working seismograph and store data onto a microSD card
  • Write software to display data onto an LCD screen
  • Add to software to send signals to cellphone via Bluetooth
  • Write a small mobile application to receive data via Bluetooth

Team Members & Responsibilities

Both team members will be working on all areas of development with specific focuses as follows:

  • Mina Yi
    • Focus on software
      • Display data on LCD screen
      • Mobile application to recognize signal
  • Andrew Ahwal
    • Focus on hardware portion to build a working seismograph

Schedule

  • Responsibility and leadership of the task is indicated by the Assignee.
    • However, it does not mean that they will be expected to complete the tasks alone.
  • Subtasks are listed in the comments section and are numbered.
  • Subtasks will be delegated as seen fit.
  • Any deviation to the schedule due to technical issues will be covered under the Testing & Technical Challenges section.

NOTE: Documentation is not specifically listed in our project schedule. However, each task has a documentation phase before and after each task.

Task# Start Date End Date Task Assignee Status Date Completed Comments
1 10/30 11/12 Order components Both Complete 11/6
2 10/31 11/7 Read datasheets & research Both Complete 11/7
3 11/6 12/1 Interfacing Bluetooth Mina Complete 12/17 1. Set up development environment

2. Create the mobile application

3. Interface SJOne board with the application

4. Send notification via bluetooth

4 11/6 11/17 Build Seismograph circuit Andrew Complete Circuit 11/13 Expected circuit completion date: 11/14

Expected testing dates: 11/14 - 11/17

5 11/18 11/18 Progress update Both Complete 11/18 In class demo of our progress.
6 11/18 11/20 Interface seismograph circuit with SJOne board Andrew Complete 11/20
7 11/21 12/7 Integrate LCD screen with SJOne board & seismograph Mina Complete 12/17 1. Fetch data created by the seismograph

2. Display data on the LCD screen

8 12/7 12/20 Testing and tweaking finalized product Both

Parts List & Cost

Part # Part Name Purchase Location Part Specification Quantity Cost per item
1 Piezoelectric Vibration Sensor With Mass wwww.sparkfun.com Sen-09197 1 $2.95
2 MicroSD Frys Electronics 16GB 1 $9.99
3 Adafruit 1.8" Color TFT Shield w/microSD and Joystick www.Amazon.com NA 1 $34.99
4 1 nF Capacitor HSC Electronics NA 2 $0.12
5 47 nF Capacitor HSC Electronics NA 1 $0.12
6 2.2 μF Capacitor HSC Electronics NA 1 $0.12
7 10 μF Capacitor HSC Electronics NA 1 $0.12
8 10 kΏ Resistor HSC Electronics NA 2 $0.10
9 11 kΏ Resistor HSC Electronics NA 1 $0.10
10 100 kΏ Resistor HSC Electronics NA 5 $0.10
11 221 kΏ Resistor HSC Electronics NA 2 $0.10
12 22 MΏ Resistor HSC Electronics NA 4 $0.10
13 Diode HSC Electronics NA 1 NA
14 OPAMP HSC Electronics LN324N 1 NA
15 Twin Through-hole Protoboard Fry's Electronics NA 1 NA
16 Various wires Fry's Electronics NA NA NA

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Documentation Issues

One of the largest deterrents in our project was due to poor or little to no documentation.

Working with the ST7735

There were problems initializing the LCD screen since the documentation was not very helpful. In addition, the board was originally intended to be used with an Arduino so we had to port the Arduino code over to work with our board.

HC-06 Bluetooth Module

Bus Contention Issues

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

References

Acknowledgement

References Used

List any references used in project.

Appendix

You can list the references you used.