Difference between revisions of "F15: TopGun"

Revision as of 02:28, 4 November 2015

Grading Criteria

Project Title

Abstract

This section should be a couple lines to describe what your project does.

Objectives & Introduction

Show list of your objectives. This section includes the high level details of your project. You can write about the various sensors or peripherals you used to get your project completed.

Team Members & Responsibilities

Motor & I/0 Controller:

• Anuj Korat
• Dhruv Kakadiya

Communication Bridge & Android Controller:

• Anush Shankar
• Aditya Devaguptapu

Geographical Controller:

• Chitrang Talaviya
• Navjot Singh

Master Controller:

• Divya Dodda

Sensor Controller:

• Hemanth Konanur Nagendra
• Akshay Vijaykumar

Treasurer:

• Anuj Korat

Schedule

Show a simple table or figures that show your scheduled as planned before you started working on the project. Then in another table column, write down the actual schedule so that readers can see the planned vs. actual goals. The point of the schedule is for readers to assess how to pace themselves if they are doing a similar project.

Team Schedule

Motor & I/O Controller Schedule

Communication bridge & Android Controller Schedule

Geographical Controller Schedule

Sensor Controller Schedule

Parts List & Cost

Design & Implementation

The design section can go over your hardware and software design. Organize this section using sub-sections that go over your design and implementation.

Hardware Design

Discuss your hardware design here. Show detailed schematics, and the interface here.

Hardware Interface

In this section, you can describe how your hardware communicates, such as which BUSes used. You can discuss your driver implementation here, such that the Software Design section is isolated to talk about high level workings rather than inner working of your project.

Software Design

Show your software design. For example, if you are designing an MP3 Player, show the tasks that you are using, and what they are doing at a high level. Do not show the details of the code. For example, do not show exact code, but you may show psuedocode and fragments of code. Keep in mind that you are showing DESIGN of your software, not the inner workings of it.

CAN Message ID Table

  reset_motorio:8;   // Acknowledge motorio controller
  reset_sensor:8;    // Acknowledge sensor controller
  reset_geo:8;       // Acknowledge geo controller
  reset_bluetooth:8;    // Acknowledge bluetooth module  

 ack_motorio:8;		// Acknowledge motorio controller
 ack_sensor:8;		// Acknowledge sensor controller
 ack_geo:8;			// Acknowledge geo controller
 ack_bluetooth:8;		// Acknowledge bluetooth module

 uint64_t front_left:8;		// Front left sensor reading
 uint64_t front_right:8;		// Front right sensor reading
 uint64_t front_center:8;	// Front centre sensor reading
 uint64_t left:8;			// Left sensor reading
 uint64_t right:8;			// Right sensor reading
 uint64_t back:8;			// Back sensor reading

 uint64_t speed:8;			// Indicate speed for DC motor
 uint64_t turn:8;			// Indicate turn angle for servo motor

 uint64_t num_of_points;	// Number of check-points to be loaded

 float latitude;
 float longitude;

 float latitude;
 float longitude;

 speed:8;		// Speed as measured by the GPS sensor
 heading:16;		// Heading from the Geo controller
 bearing:16;		// Bearing calculated by the Geo controller

 float latitude;
 float longitude;

 light_sensor:8;	// Light sensor reading
 batt_sensor:8;	// Battery level sensor reading

Implementation

This section includes implementation, but again, not the details, just the high level. For example, you can list the steps it takes to communicate over a sensor, or the steps needed to write a page of memory onto SPI Flash. You can include sub-sections for each of your component implementation.

Testing & Technical Challenges

Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again? Make a smooth transition to testing section and described what it took to test your project.

Include sub-sections that list out a problem and solution, such as:

My Issue #1

Discuss the issue and resolution.

Conclusion

Conclude your project here. You can recap your testing and problems. You should address the "so what" part here to indicate what you ultimately learnt from this project. How has this project increased your knowledge?

Project Video

Upload a video of your project and post the link here.

Project Source Code

• Sourceforge Source Code Link

References

Acknowledgement

Any acknowledgement that you may wish to provide can be included here.

References Used

List any references used in project.

Appendix

You can list the references you used.