S18: Smart Rock Paper Scissors - Revision history

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:07:47Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:07:26Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:05:22Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:05:05Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:04:35Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:03:40Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:03:25Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T14:00:28Z

‎Bluetooth Gloves

Proj user3: /* Bluetooth Gloves */

2018-05-27T13:46:02Z

‎Bluetooth Gloves

Proj user3: /* drawScoreboard(uint8_t roundNum, uint8_t leftScore, uint8_t rightScore) */

2018-05-26T17:37:10Z

‎drawScoreboard(uint8_t roundNum, uint8_t leftScore, uint8_t rightScore)

@@ Line 305: / Line 305: @@
 |}
 [[File:CMPE244 S18 RPS glove sch labeled.jpg|thumb|600px|center|frame|Glove Connection]]
 ==== LED Matrix ====

@@ Line 303: / Line 303: @@
 | P GND
 | Vibration motor GND
 |}

@@ Line 304: / Line 304: @@
 | Vibration motor GND
 |}
 ==== LED Matrix ====

@@ Line 304: / Line 304: @@
 | Vibration motor GND
 |}
-[[File:CMPE244 S18 RPS glove sch labeled.jpg|thumb|600px|left|frame|Glove Connection]]
+{[[File:CMPE244 S18 RPS glove sch labeled.jpg|thumb|600px|left|frame|Glove Connection]]}
 ==== LED Matrix ====

@@ Line 303: / Line 303: @@
 | P GND
 | Vibration motor GND
 |}
 ==== LED Matrix ====

@@ Line 238: / Line 238: @@
 ''' Vibrator Motor '''
 Vibration sensors are used as feedback to the user. One vibration sensor on each glove.
-[[File:CMPE244 S18 RPS glove sch labeled.jpg|thumb|600px|frame|Glove Connection]]
 |}

@@ Line 205: / Line 205: @@
 {| style="width:800px;" |
+|
 '''Flex Sensors'''
 Flex sensors are used to detect the hand gesture of the user. Two flex sensors are used on fingers 2 and 4, if paper both are not bent, if scissors one is bent and if rock both are bent.
 <BR/>
 ''' Bluetooth HC-05 '''
 The gloves are connected over bluetooth. Two HC-05, are used on the gloves (one each) and they serve as master modules to the 2 HC-06 xBee modules which serve as slave modules on the board.
 <BR/>
 ''' Vibrator Motor '''

@@ Line 510: / Line 510: @@
 ====== drawScoreboard(uint8_t roundNum, uint8_t leftScore, uint8_t rightScore) ======
-This function is used to draw the entire pre-round animation as well as re-draw the in-round score. First, it continually updates the frameBuffer to allow an animation of 'Round' from the bottom to the top of the screen. Once there, it displays roundNum and flashes the round before disappearing for the scoreboard. Regardless of 1P or 2P mode, the players are the same with P1 and P2/CPU. This function calls a drawCountdown() that counts down from 3 to synchronize the recorded player gestures. Afterwards, a drawAction(Action left, Action right) call is made to draw the gestures of each player. A new Action enumeration was made with Rock, Paper, and Scissors as possible options. A variation of the scoreBoard design is shown below.
+This function is used to draw the entire pre-round animation as well as re-draw the in-round score. First, it continually updates the frameBuffer to allow an animation of 'Round' from the bottom to the top of the screen. Once there, it displays roundNum and flashes the round before disappearing for the scoreboard. Regardless of 1P or 2P mode, the players are the same with P1 and P2/CPU. This function calls a drawCountdown() that counts down from 3 to synchronize the recorded player gestures. Afterwards, a drawAction(Action left, Action right) call is made to draw the gestures of each player. A new Action enumeration was made with Rock, Paper, and Scissors as possible options. A variation of the scoreBoard design is shown below. While drawStartScreen simply modifies the entire frameBuffer, drawScoreboard and its subfunctions like drawCountdown, drawScore etc, simply clear their respective sections of the screen and shift pre-drawn bit images to their correct positions.
 [[File: CMPE244_S18_RPS_RoundScreen.jpeg]]