S16: Pinball - Revision history

Preet: /* Grading Criteria */

2016-05-26T20:14:19Z

‎Grading Criteria

2016-05-25T00:53:59Z

‎Project Video

2016-05-25T00:27:30Z

‎Abstract

2016-05-25T00:27:13Z

‎Abstract

2016-05-25T00:26:48Z

‎Pinball

2016-05-25T00:18:07Z

‎Software Design

2016-05-25T00:16:10Z

‎Schedule

2016-05-25T00:15:03Z

‎References Used

2016-05-25T00:14:57Z

‎Schedule

2016-05-25T00:13:54Z

‎Pinball

← Older revision		Revision as of 20:14, 26 May 2016
Line 1:		Line 1:
−	~~=== Grading Criteria ===~~
−	~~<font color="green">~~
−	* How well is Software & Hardware Design described?
−	* How well can this report be used to reproduce this project?
−	* Code Quality
−	* Overall Report Quality:
−	** Software Block Diagrams
−	** Hardware Block Diagrams
−	**: Schematic Quality
−	** Quality of technical challenges and solutions adopted.
−	~~</font>~~
−
	=Pinball=		=Pinball=

@@ Line 292: / Line 292: @@
 === Project Video ===
-Upload a video of your project and post the link here.
+https://youtu.be/lYu_lRx3z3U
 === Project Source Code ===

@@ Line 18: / Line 18: @@
 [[File:IMG_6058.JPG|350px|thumb|left]]
 [[File:Pinball1.jpg|350px|thumb|center]]
-Finished Prototype of Pinball Machine
+Finished Pinball Machine
 <br>

@@ Line 18: / Line 18: @@
 [[File:IMG_6058.JPG|350px|thumb|left]]
 [[File:Pinball1.jpg|350px|thumb|center]]
-Figure 1 & 2. Finished Prototype of Pinball Machine
+Finished Prototype of Pinball Machine
 <br>

@@ Line 12: / Line 12: @@
 =Pinball=
 [[File:IMG_6058.JPG|350px|thumb|left]]
 [[File:Pinball1.jpg|350px|thumb|center]]
 <br>
 == Objectives & Introduction ==

@@ Line 267: / Line 267: @@
 Once the ball is launched, there will be LEDs along the ramps path that will be lit once the ball has connected the circuit. This wires will be the input that the GPIO driver will need in order to power up the LEDs that are on the side of the ramp. By doing so, we are able to allocate points to the user and the scoreboard, and it will indicate where the ball is on the playing field.
-To control the flippers, which are connected to the servos, we utilize
+To control the flippers, which are connected to the servos, we utilized PWM, which is Pulse Width Modulation.
 === Implementation ===

@@ Line 83: / Line 83: @@
 | 5/01
 | 1. Incorporate all components into the designed pinball skeleton <br> 2. Begin component/unit testing <br> 3. Troubleshoot/Debug as needed
-| In-Progress
+| Completed
+| The 3D printed Bumpers and flippers were the most important components needed to finalize the pinball machine. Once theses items were ready, the overall design became more defined. The gears and buttons were testes to make sure the flippers worked synchronously
 |-
 ! scope="row"| 6
@@ Line 90: / Line 90: @@
 | 5/08
 | Product testing and final adjustments
-| In-Progress
+| Completed
+| All the components were mounted and adjustments were made to the design. The ball loaded runway needed a lot of work to make sure the ball rolled over the nails easily
 |-
 ! scope="row"| 7
@@ Line 97: / Line 97: @@
 | 5/15
 | Final Product Testing
-| In-Progress
+| Completed
+| Unfortunately, the color LEDs did not turn ON during testing. Because this was an added feature to the project, we felt okay going into demo without them functioning
 |-
 |}

← Older revision		Revision as of 00:15, 25 May 2016
Line 317:		Line 317:

	<b>8-line to 3-line Priority Encoder </b>http://www.farnell.com/datasheets/93457.pdf		<b>8-line to 3-line Priority Encoder </b>http://www.farnell.com/datasheets/93457.pdf
		+
		+	<b>Rainbow Colored LEDs</b> http://www.karlssonrobotics.com/datasheets/Components/LED/YSL-R596CR4G3B5W-F12.pdf

	=== Appendix ===		=== Appendix ===

@@ Line 63: / Line 63: @@
 | 1. Component research and initial pinball design <br> 2. Begin component purchasing
 | Completed
-| Completed
+| Completed. Ordering the parts was very time consuming. We recommend putting more time into planning and purchasing the components ahead of time. There was a lot of last minute purchases as well as, unnecessary purchases made. Overall, we did well splitting up the cost and making sure we had the parts in a reasonable time frame
 |-
 ! scope="row"| 3