S15: Remote Learner - Revision history

Proj user11: /* Android App Testing */

2015-05-25T08:15:35Z

‎Android App Testing

2015-05-25T07:06:23Z

‎Android Application with SJOne Board Hardware Design

2015-05-25T07:06:09Z

‎Android Application with SJOne Board Hardware Design

2015-05-25T07:01:03Z

‎Remote Learner Android App

2015-05-25T06:55:56Z

‎Remote Learner Android App

2015-05-25T06:50:13Z

‎Remote Learner Android App

2015-05-25T06:41:34Z

‎Android Application with SJOne Board Hardware Design

2015-05-25T06:37:27Z

‎Android Application with SJOne Board Hardware Design

2015-05-25T04:32:32Z

‎Conclusion

2015-05-25T04:21:18Z

‎Testing & Technical Challenges

@@ Line 530: / Line 530: @@
 === Android App Testing ===
-This section is for android app testing.
+The initial testing and debugging was used with the Android emulator. The built-in emulator allows real time debugging, it was very helpful for confirming simple events within the application. After Bluetooth chat service was implemented, a real Android device and logging was used for testing and debugging.
 == Conclusion ==

@@ Line 259: / Line 259: @@
 {| style="width:800px;" |
-|[[File:CMPE244_S15_TEAM2_Android_Block_Diagram.jpg|600px|center|thumb|Android Hard Design: System Block Diagram]]
+|[[File:CMPE244_S15_TEAM2_Android_Block_Diagram.jpg|600px|center|thumb|Android Hardware Design: System Block Diagram]]
 |}

@@ Line 259: / Line 259: @@
 {| style="width:800px;" |
-|[[File:CMPE244_S15_TEAM2_Android_Block_Diagram.jpg|600px|center|thumb|Android App: Starting Screen]]
+|[[File:CMPE244_S15_TEAM2_Android_Block_Diagram.jpg|600px|center|thumb|Android Hard Design: System Block Diagram]]
 |}

@@ Line 493: / Line 493: @@
 <br/><br/>
 {| style="width:1200px;" |
 |[[File:CMPE244_S15_TEAM2_Android_Connected.png|350px|left|thumb|Android App: Bluetooth Device Connected]]

← Older revision		Revision as of 06:55, 25 May 2015
Line 484:		Line 484:
	<br/><br/>		<br/><br/>

		+	The Remote Learner application initial screen is shown in the left figure below. It has the capability to pair up with an Bluetooth device, then transmit commands to the device. Under the application title, there is a status message that updates instantaneously from initiating and establishing Bluetooth connection requests.

	{\| style="width:1200px;" \|		{\| style="width:1200px;" \|

@@ Line 478: / Line 478: @@
 === Remote Learner Android App ===
-The software development environment for the Remote Learner android application is Android Studio 1.2.1.1.
+The software development environment for the Remote Learner Android application is Android Studio 1.2.1.1, it is the official IDE for Android application development, based on IntelliJ IDEA. The IDE simplified the way how Android application was developed traditionally. It comes with a built-in Android Emulator so there was no need additional plug-in or downloads. However, in the Remote Learner application, Android emulator was not very helpful because it requires an active Bluetooth connection. Hence, a real Android device was used throughout development. Figures below show the Remote Leaner Android application and its design layout. At the same time, it has the capability to receive status from the SJOne board after an command has been sent.
 [[File:CMPE244_S15_TEAM2_Android_AndroidStudio.png|900px|center|thumb|Android App: Development Envirnoment]]

@@ Line 256: / Line 256: @@
 ====Android Application with SJOne Board Hardware Design ====
-The Android application hardware design consists of the Bluetooth module (HC-06) and SJOne board. The communication link is established using the SJOne board UART3 Tx and Rx Pins.
+The Android application hardware design consists of the Bluetooth module (HC-06) and SJOne board as shown in the figure below. The communication link is established using the SJOne board UART3 Tx and Rx Pins and the HC-06 Bluetooth module. Messages are being sent in a hand shake manner. Once the SJOne board received an command, the transmit and receive tasks would act accordingly. After the operations are completed, it would notify the Android application the result of the requested command.
 {| style="width:800px;" |

@@ Line 527: / Line 527: @@
 == Conclusion ==
-Conclude your project here.  You can recap your testing and problems.  You should address the "so what" part here to indicate what you ultimately learnt from this project.  How has this project increased your knowledge?
+Our team was successful in completing the Remote Learner project. We faced a few issues such as debugging the PWM frequency to the correct value and integrating the project together. Our team expanded our knowledge of using FreeRTOS to implement individual task and having them communicate with each other thru queue. We learned about the different protocols such as NEC that was used by some of the devices we tested. Lastly, we learn how to develop an Android application to control everything.
 === Project Video ===

← Older revision		Revision as of 04:21, 25 May 2015
Line 497:		Line 497:

	== Testing & Technical Challenges ==		== Testing & Technical Challenges ==
−	~~Describe the challenges of your project. What advise would you give yourself or someone else if your project can be started from scratch again?~~
−	~~Make a smooth transition to testing section and described what it took to test your project.~~
−
−	~~Include sub-sections that list out a problem and solution, such as:~~

	=== IR Transmit Issue #1 ===		=== IR Transmit Issue #1 ===